ETSI TR 103 061-1-2014 Intelligent Transport Systems (ITS) Testing Part 1 Conformance test specifications for Co-operative Awareness Messages (CAM) CAM validation report (V1 2 1)《智_1.pdf

1、 ETSI TR 103 061-1 V1.2.1 (2014-04) Intelligent Transport Systems (ITS); Testing; Part 1: Conformance test specifications for Co-operative Awareness Messages (CAM); CAM validation report Technical Report ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)2Reference RTR/ITS-00137 Keywords application, interopera

2、bility, ITS, OTE, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document

3、can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or

4、perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to

5、revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_suppo

6、rt.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization o

7、f ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade

8、 Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)3Contents Intellectual Property Rights 4g3Foreword . 4g3Introduction 4g31 Scope 5

9、g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Abbreviations . 6g34 Validation report 6g34.1 Validation level 6g34.2 Source code evaluation . 6g34.2.1 TTCN-3 version 6g34.2.2 TTCN-3 tools used for compilation 6g34.3 Validation Process 7g34.3.1 Test Platforms. 7g34.3.

10、2 SUTs . 7g34.3.3 Validation Status . 7g34.4 Feedback to standardization process 8g34.4.1 Base standard issues 8g34.4.2 Test specification issues 8g34.4.3 Typical SUT issues . 8g3Annex A: Bibliography 9g3History 11g3ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)4Intellectual Property Rights IPRs essential

11、or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Es

12、sential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

13、can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Report (TR) has been produced by ETSI Technical Committee Intelligent Transport Sys

14、tems (ITS). The present document is part 1 of a multi-part deliverable covering the Intelligent Transport Systems (ITS); Testing, as identified below: Part 1: “Conformance test specifications for Co-operative Awareness Messages (CAM); CAM validation report“; Part 2: “Conformance test specifications

15、for Decentralized Environmental Notification basic service Messages (DENM); DENM validation report“; Part 3: “Conformance test specification for Geographical addressing and forwarding for point-to-point and point-to-multipoint communications; GeoNetworking validation report“; Part 4: “Conformance te

16、st specification for GeoNetworking Basic Transport Protocol (BTP); GeoNetworking BTP validation report“; Part 5: “IPv6 over GeoNetworking validation report“. Introduction In response to EC mandate M/453, ETSI Technical Committee ITS has standardized base and test specifications for ITS protocols. In

17、 a next step a prototype TTCN-3 test system was built and validated. The present document and its related TR 103 099 i.5 (Architecture of Conformance Validation Framework), describe the validation and design of the prototype TTCN-3 test system. The action described in the present document has suppor

18、ted the implementation of ITS standards by: Making available validated and standardized test specifications and thus enabling the application of reliable certification schemes. Executing conformance validation framework against real Implementations Under Test (IUTs) from industry and thus providing

19、these companies with a conformance assessment of their implementations. During the lifetime of this action, the conformance validation framework was as well provided at ITS Cooperative Mobility Services Interoperability events. Releasing all software as open source and thus allowing industry to buil

20、d and run their own conformance validation framework. ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)51 Scope The present document is the validation report of the CAM conformance tests i.2 derived from EN 302 637-2 i.1. It provides statistics of executed and validated CAM conformance tests. The information

21、provided has been produced by validation against at least two prototype implementations from industry. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For

22、 non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause

23、were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references The following referenced documents are not necessar

24、y for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EN 302 637-2 (V1.3.0): “Intelligent Transport Systems (ITS); Vehicular Communications; Basic Set of Applications; Part 2: Specification of Cooperative Awareness Basic Service“. i

25、.2 ETSI TS 102 868-3 (V1.1.1): “Intelligent Transport Systems (ITS); Testing; Conformance test specification for Co-operative Awareness Messages (CAM); Part 3: Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)“. i.3 ETSI TS 102 868-3 (V1.2.1): “Intelligent T

26、ransport Systems (ITS); Testing; Conformance test specifications for Co-operative Awareness Messages (CAM); Part 3: Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)“. i.4 ETSI TS 102 894-2 (V1.1.1): “Intelligent Transport Systems (ITS); Users and applicatio

27、ns requirements; Part 2: Applications and facilities layer common data dictionary“. i.5 ETSI TR 103 099 (V1.2.1): “Intelligent Transport Systems (ITS); Architecture of conformance validation framework“. i.6 ETSI EG 201 015 (V1.1.1): “Methods for Testing and Specification (MTS); Specification of prot

28、ocols and services; Validation methodology for standards using SDL; Handbook“. i.7 ETSI ES 201 873-1 (V4.5.1): “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)63 Abbreviations For the

29、 purposes of the present document, the following abbreviations apply: ASN.1 Abstract Syntax Notation One ATS Abstract Test Suite CAM Co-operative Awareness Message EC European CommissionITS Intelligent Transport Systems IUT Implementation Under Test PICS Protocol Implementation Conformance Statement

30、 SUT System Under Test TC Test cases TP Test PurposesTTCN-3 Testing and Test Control Notation 3 VPN Virtual Private Network 4 Validation report 4.1 Validation level Level 3 (Rigorous) abstract test suite validation has been performed, according to the validation handbook i.6: the test suite has been

31、 compiled on more than one TTCN-3 tool; the complete suite of tests has been implemented and executed on more than one test platform; the complete suite of tests have been executed against SUTs from a range of different suppliers; the operation and output traces of all the tests have been validated.

32、 4.2 Source code evaluation 4.2.1 TTCN-3 version The CAM abstract test suite is based on TTCN-3 edition 4.5.1 (ES 201 873-1 i.7). 4.2.2 TTCN-3 tools used for compilation The test suite has been compiled using two different TTCN-3 tools, as detailed in table 1. Table 1: TTCN-3 tools used for compilat

33、ion Supplier Tool name Version Settings Compilation result TestingTech TTworkbench 1.1.16 Support for very large integers ASN.1-Language-Support-v1.1.4 No error, no warning Elvior TestCast T3 6.7.2.1 No error, no warning NOTE: This information is given for the convenience of users of the present doc

34、ument and does not constitute an endorsement by ETSI of these products. ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)74.3 Validation Process 4.3.1 Test Platforms The validation test platform has been built as described in the conformance validation framework i.5 using the components as described in table

35、2. Table 2: Validation test platform components TTCN-3 Tool TestingTech TTworkbench v16 with ASN.1 support plugin Test Adapter The applicable software tag is: http:/forge.etsi.org/websvn/listing.php?repname=ITS.ITS Vehicular Communications; Basic Set of Applications; Part 2: Specification of Coopera

36、tive Awareness Basic Service“. ETSI TS 102 868-1 (V1.2.1): “Intelligent Transport Systems (ITS); Testing; Conformance test specification for Co-operative Awareness Messages (CAM); Part 1: Test requirements and Protocol Implementation Conformance Statement (PICS) proforma“. ETSI TS 102 868-2 (V1.2.1)

37、: “Intelligent Transport Systems (ITS); Testing; Conformance test specification for Co-operative Awareness Messages (CAM); Part 2: Test Suite Structure and Test Purposes (TSS The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. ETSI EG 202 798 (V1.1.1): “Intelligent Transp

38、ort Systems (ITS); Testing; Framework for conformance and interoperability testing“. ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)10List of tables Table 1: TTCN-3 tools used for compilation . 6g3Table 2: Validation test platform components . 7g3Table 3: SUTs used for validation 7g3Table 4: Testcase validation status . 7g3ETSI ETSI TR 103 061-1 V1.2.1 (2014-04)11History Document history V1.1.1 November 2012 Publication V1.2.1 April 2014 Publication