ETSI TR 103 101-2014 Intelligent Transport Systems (ITS) Test suite validation Access technology support ISO 21218 (V1 1 1)《智能运输系统 (ITS) 试验套件验证 访问技术支持 ISO 21218 (V1 1 1)》.pdf

1、 ETSI TR 103 101 V1.1.1 (2014-06) Intelligent Transport Systems (ITS); Test suite validation; Access technology support ISO 21218 Technical Report ETSI ETSI TR 103 101 V1.1.1 (2014-06) 2Reference DTR/ITS-0020050 Keywords CALM, ITS, testing, validation ETSI 650 Route des Lucioles F-06921 Sophia Antip

2、olis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be mad

3、e available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, th

4、e only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this an

5、d other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any

6、 form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction

7、 in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP O

8、rganizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TR 103 101 V1.1.1 (2014-06) 3Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g3

9、2.2 Informative references 5g33 Abbreviations . 6g34 Validation report 6g34.1 Validation level 6g34.2 Source code evaluation . 6g34.2.1 TTCN-3 version 6g34.2.2 TTCN-3 tools used for compilation 6g34.3 Validation process 7g34.3.1 Test platform. 7g34.3.2 Systems under test 7g34.3.3 Validation status .

10、 7g34.4 Feedback to standardization process 8g3History 9g3ETSI ETSI TR 103 101 V1.1.1 (2014-06) 4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly availa

11、ble for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server

12、 (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, e

13、ssential to the present document. Foreword This Technical Report (TR) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “may not“, “need“, “need not“, “will“, “will n

14、ot“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction In response to EC mandate M/453, ETSI Tech

15、nical Committee ITS has standardized test specifications for ITS protocols according to base standards from ISO TC204 WG16. In a next step a prototype TTCN-3 test system was built and validated. The present document describes the validation and design of the prototype TTCN-3 test system. The action

16、described in the present document supports the implementation of ITS standards by: Making available validated and standardized test specifications and thus enabling the application of reliable certification schemes. Executing conformance validation framework against real Implementations Under Test (

17、IUTs) from industry and thus providing these companies a conformance assessment of their implementations. During the lifetime of this action, the conformance validation framework was as well demonstrated at a meeting of ISO TC204 in Kobe (Japan), and at an ETSI PlugTest. Releasing all software as op

18、en source and thus allowing industry to build and run their own conformance validation framework. ETSI ETSI TR 103 101 V1.1.1 (2014-06) 51 Scope The present document is the validation report of the ATSP conformance tests and it provides statistics of executed and validated ATSP conformance tests. Th

19、e information provided has been produced by validation against one prototype implementation from industry. Furthermore, identified issues related to the base specifications ISO 21218 i.3 and test specification ETSI TS 102 760-1 i.4, ETSI TS 102 760-2 i.5, and ETSI TS 102 760-3 i.6 are listed in the

20、present document. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including an

21、y amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity

22、. 2.1 Normative references The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to

23、 a particular subject area. i.1 ETSI TR 103 099 (V1.1.1): “Intelligent Transport Systems (ITS); Architecture of conformance validation framework“. i.2 ETSI EG 201 015 (V1.1.1): “Methods for Testing and Specification (MTS); Specification of protocols and services; Validation methodology for standards

24、 using SDL; Handbook“. i.3 ISO 21218:2013: “Intelligent transport systems - Communications access for land mobiles (CALM) - Access technology support“. i.4 ETSI TS 102 760-1 (V1.2.1): “Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for Access

25、Technology Support (ISO 21218); Part 1: Implementation Conformance Statement (ICS) proforma“. i.5 ETSI TS 102 760-2 (V1.2.1): “Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for Access Technology Support (ISO 21218); Part 2: Test Suite Structu

26、re and Test Purposes (TSS Communications Access for Land Mobiles (CALM); Test specifications for Access Technology Support (ISO 21218); Part 3: Abstract Test Suite (ATS) and partial PIXIT proforma“. i.7 ETSI ES 201 873-1: “Methods for Testing and Specification (MTS); The Testing and Test Control Not

27、ation version 3; Part 1: TTCN-3 Core Language“. ETSI ETSI TR 103 101 V1.1.1 (2014-06) 63 Abbreviations For the purposes of the present document, the following abbreviations apply: ASN Abstract Syntax Notation ATS Abstract Test Suite ATSP Access Technology Support Protocols ITS Intelligent Transport

28、Systems ITS Intelligent Transportation Systems ITS-SU ITS Station Unit PICS Protocol Implementation Conformance Statement STF Specialist Task Force SUT System Under Test TC Test case TP Test Purpose TTCN-3 Testing and Test Control Notation 3 4 Validation report 4.1 Validation level Level 3 (Rigorous

29、) abstract test suite validation has been performed, according to the validation handbook ETSI EG 201 015 i.2: the test suite has been compiled on more than one TTCN-3 tool; the complete suite of tests has been implemented and executed on two test platform; the suite of tests for implemented protoco

30、l options have been executed against SUTs from a range of different suppliers; the operation and output traces of all the tests have been validated. 4.2 Source code evaluation 4.2.1 TTCN-3 version The ATSP abstract test suite ETSI TS 102 760-3 i.6 is based on TTCN-3 edition 4.2.1 (TTCN3:2010) specif

31、ied in ETSI ES 201 873-1 i.7. 4.2.2 TTCN-3 tools used for compilation The ATSP abstract test suite ETSI TS 102 760-3 i.6 has been compiled using three different TTCN-3 tools, as detailed in table 1. Table 1: TTCN-3 tools used for compilation Supplier Tool name Version Settings Compilation result Elv

32、ior TestCast T3 6.7.2.1 No error, no warning TestingTech TTworkbench 1.1.16 Support for very large integers ASN.1-Language-Support-v1.1.4 No error, no warning OpenTTCN OpenTTCN Tester 2012 4.2.2 No error, no warning NOTE: This information is given for the convenience of users of the present document

33、 and does not constitute an endorsement by ETSI of these products. ETSI ETSI TR 103 101 V1.1.1 (2014-06) 74.3 Validation process 4.3.1 Test platform The validation test platform has been based on the conformance validation framework outlined in ETSI TR 103 099 i.1 using the components presented in t

34、able 2. Table 2: Validation test platform components TTCN-3 Tool Elvior TestCastT3 v6.7.2.1 TTCN-3 Tool TestingTech TTworkbench v13 with ASN.1 support plugin Test Adapter Software: Implemented by STF424/STF455. ITS Test Adapter v1.1.2 Codec Implemented by STF424/STF455. ITS Codec v1.1.2 NOTE: This i

35、nformation is given for the convenience of users of the present document and does not constitute an endorsement by ETSI of these products. 4.3.2 Systems under test As no commercial implementation of ATSP in an ITS-SU was available, validation tests were performed against a light software implementat

36、ion. As a consequence, none of the validation tests for the test group TC_ATSP_DP could be executed. It is intended to perform further validation tests as part of the work of TC ITS WG2 once an SUT will be available. 4.3.3 Validation status Table 3 shows the validation status of each test case of th

37、e ATSP abstract test suite. Table 3: Testcase validation status TC identifier Verdict Log analysis Validated TC_ATSP_SE_BV_07 PASS OK YesTC_ATSP_SE_BV_09 PASS OK Yes TC_ATSP_SE_BV_11 PASS OK YesTC_ATSP_MB_BV_01 PASS OK Yes TC_ATSP_MB_BV_02 PASS OK Yes TC_ATSP_MB_BI_01 PASS OK Yes TC_ATSP_MB_BI_02 PA

38、SS OK Yes TC_ATSP_MB_BI_03 PASS OK Yes TC_ATSP_HC_BV_03 PASS OK Yes TC_ATSP_HC_BV_04 PASS OK Yes TC_ATSP_HC_BV_05 PASS OK Yes TC_ATSP_HC_BI_01 PASS OK Yes TC_ATSP_SE_BV_01 PASS OK YesTC_ATSP_SE_BV_02 PASS OK Yes TC_ATSP_SE_BV_03 PASS OK YesTC_ATSP_SE_BV_04 PASS OK Yes TC_ATSP_SE_BV_05 PASS OK YesTC_

39、ATSP_SE_BV_06 PASS OK Yes TC_ATSP_SE_BV_08 Tests not executed due to missing implementations in the software simulator TC_ATSP_SE_BV_10 TC_ATSP_SE_BV_12 TC_ATSP_SE_BV_13 TC_ATSP_SE_BV_14 TC_ATSP_SE_BV_15 TC_ATSP_SE_BV_16 TC_ATSP_SE_BV_17 TC_ATSP_SE_BI_01 TC_ATSP_SE_BI_02 TC_ATSP_MB_BV_03 TC_ATSP_HC_

40、BV_01 TC_ATSP_HC_BV_02 ETSI ETSI TR 103 101 V1.1.1 (2014-06) 8TC identifier Verdict Log analysis Validated TC_ATSP_DP_BV_01 TC_ATSP_DP_BV_02 TC_ATSP_DP_BV_03 TC_ATSP_DP_BV_04 TC_ATSP_DP_BV_05 TC_ATSP_DP_BV_06 TC_ATSP_DP_BV_07 TC_ATSP_DP_BV_08 TC_ATSP_DP_BV_09 TC_ATSP_DP_BV_10 TC_ATSP_DP_BV_11 TC_ATS

41、P_DP_BV_12 TC_ATSP_DP_BV_13 TC_ATSP_DP_BV_14 TC_ATSP_DP_BI_01 TC_ATSP_DP_BI_02 4.4 Feedback to standardization process No explicit feedback to SDOs (ETSI and ISO) was needed. Experience from validation was directly used to improve the test suite as part of the work of STF 455. Further changes of the ISO base standard ISO 21218 i.3 are not needed. ETSI ETSI TR 103 101 V1.1.1 (2014-06) 9History Document history V1.1.1 June 2014 Publication