ETSI TR 126 967-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) eCall data transfer In-band modem solution (V15 0.pdf

1、 ETSI TR 126 967 V15.0.0 (2018-07) Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); eCall data transfer; In-band modem solution (3GPP TR 26.967 version 15.0.0 Release 15) TECHNICAL REPORT GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI

2、 TR 126 967 V15.0.0 (2018-07)13GPP TR 26.967 version 15.0.0 Release 15Reference RTR/TSGS-0426967vf00 Keywords GSM,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif

3、 enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the prese

4、nt document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network dri

5、ve within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in th

6、e present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as au

7、thorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are tr

8、ademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by th

9、e GSM Association. ETSI ETSI TR 126 967 V15.0.0 (2018-07)23GPP TR 26.967 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if an

10、y, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available o

11、n the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or m

12、ay be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no r

13、ight to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Report (TR) has been produced by ETSI 3rd Generatio

14、n Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and

15、ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for

16、the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TR 126 967 V15.0.0 (2018-07)33GPP TR 26.967 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4

17、g3Introduction 4g31 Scope 5g32 References 5g33 Definitions and abbreviations . 5g33.1 Definitions 5g33.2 Abbreviations . 6g34 Outline of the present document 6g35 eCall MSD data transmission requirements . 7g36 Analysis of eCall via CTM against the service requirements 7 g37 Conclusion on the analys

18、is of eCall MSD data transmission requirements . 9g3Annex A: Brief description of the existing CTM . 11g3Annex B: Description of eCall via CTM 12g3B.1 Detailed specification of one possible protocol 12g3B.2 Detailed specification of the eCall transmission 13g3Annex C: Performance characterization of

19、 eCall via CTM . 15g3Annex D: Possible architecture and interface to the UE 20g3Annex E: Network architectures and interfaces for eCall . 21g3E.1 Circuit switched network architecture and anterfaces for eCall . 21g3E.2 Architecture and interfaces for Global Text Telephony . 22g3E.3 Coexistence of Gl

20、obal Text Telephony and eCall via CTM 22g3E.4 Compatibility of eCall via CTM to IP transport . 23g3E.4.1 Compatibility of eCall via CTM to IP transport on the fixed side 23g3E.4.2 Compatibility of eCall via CTM to IP transport on the Radio Interface 24g3Annex F: Potential for pptimizations of eCall

21、via CTM . 25g3F.1 Potential for optimizations of CTM . 25g3F.2 Potential for optimizations of the eCall protocol . 25g3Annex G: Change history . 26g3History 27g3ETSI ETSI TR 126 967 V15.0.0 (2018-07)43GPP TR 26.967 version 15.0.0 Release 15Foreword The present document has been produced by the 3rdGe

22、neration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release da

23、te and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. techni

24、cal enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introduction eCall is a European-wide solution for automatically or manually initiated emergency voice calls. eCall will supplement E112 and 112 (TS12) em

25、ergency call with related data from the vehicle, e.g. highly accurate location information. The expected benefit is that emergency services will be made aware of accidents much more rapidly, will get precise information on location, vehicle type etc. and therefore will be able to reach accident vict

26、ims faster, with the potential to save many lives annually. According to reports from the European Commission, it is envisioned that eCall will be offered on all new vehicles in the EU by 2010. It is expected that the eCall data will be sent either during the E112 call set-up or immediately followin

27、g the establishment of the voice call or at any point later during the voice call. The integrity of the eCall data sent from the vehicle to the Public Safety Access Point has to be ensured. eCall is a European regional requirement. It shall not have an impact on the global circulation of terminals.

28、ETSI ETSI TR 126 967 V15.0.0 (2018-07)53GPP TR 26.967 version 15.0.0 Release 151 Scope The European Union eCall requirements, recommendations and guidelines were developed by eSafety Forum, with important additional work produced by ETSI MSG, GSME, 3GPP, and CEN. Previous work in 3GPP TR 22.967 2 Tr

29、ansfer of Emergency Call Data, examined the issues associated with the transmission of emergency call data from a vehicle to a PSAP. This analysis identified that the preferred option be based on an in-band modem solution. The objective of this work was to examine and describe the in band modem solu

30、tion (in band modem and any necessary interface to the ME) for eCall. Because eCall is a European regional requirement, it shall not have an impact on the global circulation of terminals. In the interest of not duplicating work, the set of in-band solutions that were considered are those preferred b

31、y GSME unless significant improvements are available. The work assessed the suitability of existing 3GPP in-band solutions, e.g. CTM, to satisfy the requirements for eCall. The present document assesses the suitability of CTM for eCall. 2 References The following documents contain provisions which,

32、through reference in this text, constitute provisions of the present document. - References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, th

33、e latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 22.101: “Service aspects; Service principles“. 2 3GPP TR 22.967

34、: “Transferring of emergency call data“. 3 3GPP TS 26.226: “Cellular text telephone modem; General description“. 4 3GPP TS 26.230: “Cellular text telephone modem; Transmitter bit exact C-code“. 5 3GPP TS 26.231: “Cellular text telephone modem; Minimum performance requirements“. 6 3GPP TR 26.975: “Pe

35、rformance characterization of the Adaptive Multi-Rate (AMR) speech codec“. 7 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 8 3GPP TS 26.114: “IP Multimedia Subsystem (IMS); Multimedia telephony; Media handling and interaction“. 9 3GPP TR 26.935: “Packet Switched (PS) conversational multimedi

36、a applications; Performance characterization of default codecs“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 21.905 7 and the following apply. A term defined in the present document takes precedence over the definiti

37、on of the same term, if any, in TR 21.905 7. eSafety: European Commission sponsored forum to improve safety aspects of European citizens ETSI ETSI TR 126 967 V15.0.0 (2018-07)63GPP TR 26.967 version 15.0.0 Release 153.2 Abbreviations For the purposes of the present document, the abbreviations given

38、in TR 21.905 7 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 7. ACEA European Automobile Manufacturers Association AMR Adaptive Multi Rate CEN Comite Europeen de Normalisation (European Com

39、mittee for Standardisation) CTM Cellular Text telephony Modem EC European Commission eCall Emergency Call defined under the eSafety initiative ETSI European Telecommunications Standards Institute EU European Union FR Full Rate GSM Global System for Mobile communications GSME GSM Europe IVS In Vehicl

40、e System MSD Minimum Set of incident Data MSG (ETSI TC) Mobile Standards Group PSAP Public Service Answering Point SIM Subscriber Identity Module USIM Universal Subscriber Identity Module 4 Outline of the present document The present document analyses the suitability of the existing “Cellular Text t

41、elephony MODEM“ (CTM) for the transmission of eCall data via the voice channel from the “In-Vehicle System“ (IVS) to the “Public Safety Answering Point“ (PSAP). Chapter 5 reprints the service requirements for the eCall transmission, as specified in TS 22.101, for convenience. Chapter 6 assesses poin

42、t by point these requirements against the performance of the eCall transmission via CTM as outlined in the Annexes A, B, C. Chapter 7 provides the Conclusions. The following annexes are also included: Annex A gives a brief description of CTM with respect to its application for eCall. Annex B outline

43、s one possible protocol that utilizes CTM for the secured transmission of the eCall data through the voice channel. Annex C reports the analysis for eCall via CTM, under the condition that the outlined protocol is used. Annex D discusses the architecture for eCall in the vehicle in order to identify

44、 the interface to the UE and to analyze potential open issues. Annex E gives examples of network architectures today and in future and discusses VoIP and the future All-IP scenarios. Also the co-existence of eCall and Global Text Telephony is described here. Annex F discusses potential Optimizations

45、 for CTM and for the proposed eCall Protocol. ETSI ETSI TR 126 967 V15.0.0 (2018-07)73GPP TR 26.967 version 15.0.0 Release 155 eCall MSD data transmission requirements Based on input from external sources, like EC, eSafety and ETSI-MSG, 3GPP has developed a set of requirements for the in-band modem

46、solution for eCall, see TS 22.101 1. Begin of Extract from TS 22.101 (V8.6.0) 1: TS 22.101, Clause 10.7 “Transfer of data during emergency calls“ Emergency calls may be supplemented with emergency related data 1. Typically this data enables the accurate geographic location of a manually or automatic

47、ally activated emergency calling device e.g. an in vehicle system (IVS), to be provided to the Public Safety Answering Point (PSAP). - The data may be sent prior to, in parallel with, or at the start of the voice component of an emergency call. - Should the PSAP request additional data then this may

48、 be possible during the established emergency call. - The realisation of the transfer of data during an emergency call shall minimise changes to the originating and transit networks. - Both the voice and data components of the emergency call shall be routed to the same PSAP or designated emergency c

49、all centre. - The transmission of the data shall be acknowledged and if necessary data shall be retransmitted. - A UE configured only to transfer data during emergency calls (e.g. eCall only UE) shall not generate signalling to the network besides what is needed to place an emergency call. Additional national and regional requirements are as specified in annex A TS 22.101, Annex A.27 “Requirements for the transfer of eCall Minimum Set of Data (MSD)“ With the exception of the following specific requirements, considered necessary for the satis