ETSI TR 143 026-2016 Digital cellular telecommunications system (Phase 2+) Multiband operation of GSM DCS 1800 by a single operator (V13 0 0 3GPP TR 43 026 version 13 0 0 Release .pdf

1、 ETSI TR 1Digital cellular telecoMultiband operation of(3GPP TR 43.0TECHNICAL REPORT 143 026 V13.0.0 (2016communications system (Phaof GSM / DCS 1800 by a single.026 version 13.0.0 Release 13GLOBAL SYSTEMOBILE COMMUN16-01) hase 2+); gle operator 13) TEM FOR ICATIONSRETSI ETSI TR 143 026 V13.0.0 (201

2、6-01)13GPP TR 43.026 version 13.0.0 Release 13Reference RTR/TSGG-0143026vd00 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture

3、 de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modi

4、fied without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. U

5、sers of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your co

6、mment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.

7、 The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo ar

8、e Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TR 143 026 V13.0.0 (2

9、016-01)23GPP TR 43.026 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be

10、found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR

11、 Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This

12、 Technical Report (TR) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI

13、deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be

14、interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TR 143 026 V13.0.0 (2016-01)33GPP TR 43.026 version 13.0.0 Release 13Contents I

15、ntellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 5g31.1 References 5g31.2 Abbreviations . 5g32 General . 5g32.1 Multiband MSs . 5g32.2 Frequency bands of operation 5g32.3 Backwards compatibility 5g32.4 PLMN codes . 6g32.5 Other systems . 6g33 Requirements

16、 6g33.1 User requirements. 6g33.2 Operator requirements 6g33.3 Radio requirements. 7g33.4 Relation to frequency hopping . 7g34 Functional description 7g34.1 Idle mode procedures . 7g34.1.1 PLMN selection 7g34.1.2 Cell re-selection 7g34.1.3 Location areas . 7g34.2 Connected mode procedures. 7g34.3 Ha

17、ndover 8g34.4 Frequency and power capabilities 8g35 Technical realization and amendments 8g35.1 Mixed neighbour cell lists 8g35.2 Frequency and power capabilities 9g35.3 Measurement reports 9g36 Backwards compatibility 9g36.1 Support of single band operation 9g36.1.1 Single band MSs . 9g36.1.2 Singl

18、e band networks 9g36.2 Mixed neighbour cell lists 10g36.2.1 Phase 1 MSs 10g36.2.2 Phase 2 MSs 10g36.3 Detected compatibility problems and their solutions (when possible) . 10g36.3.1 New messages on the BCCH 10g36.3.2 New messages on the SACCH 10g3Annex A: List of amendments necessary . 11g3A.1 Appro

19、ved by TC SMG for Phase 2 11g3A.2 Approved by TC SMG and put on HOLD . 11g3A.3 Proposed for WI “Technical enhancements“ and required by WI “Multiband operation“ . 11g3A.4 Proposed for WI “Multiband operation“ 11g3A.5 Change Requests related to WI “Multiband operation“ after 1996 13g3Annex B: Change

20、History . 15g3History 16 ETSI ETSI TR 143 026 V13.0.0 (2016-01)43GPP TR 43.026 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may

21、change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 p

22、resented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated

23、 in the document. ETSI ETSI TR 143 026 V13.0.0 (2016-01)53GPP TR 43.026 version 13.0.0 Release 131 Scope The purpose of the present document is to describe the functionality of a Multiband GSM/DCS Network operated by a single operator and the Multiband GSM/DCS Mobile Station (MS). It also describes

24、the necessary amendments to the GSM/DCS phase 2 specifications for the technical realization of the function. The resulting Amendment Requests (AR) and Change Requests (CR) necessary for Multiband Operation are listed in annex A. 1.1 References Not relevant to the present document. 1.2 Abbreviations

25、 Abbreviations used in the present document are listed in GSM 01.04. 2 General Multiband operation of GSM/DCS by a single operator enables an operator, with licenses in more than one of the frequency bands specified in the GSM specifications, to support the use of multiband MSs in all bands of the l

26、icenses. In addition it also enables the operator to support the use of single band MSs in, at least, one band of the licenses. Multiband GSM/DCS MSs, are MSs which are capable of using more than one of the frequency bands specified in the GSM specifications. The multiband MS is specified in GSM 02.

27、06. (AR02.06-A001) and in section 2.1. The use of multiband operation and development of multiband MSs are optional for operators and manufactures. 2.1 Multiband MSs A MS which supports more than one band and the functionality below is defined as a Multiband MS. The multiband MS has the functionalit

28、y to perform handover, channel assignment, cell selection and cell re-selection between all its bands of operation within one PLMN, i.e. when one PLMN code is used in all bands. In addition it has the functionality to make PLMN selection, in manual or automatic mode, in all its bands of operation. T

29、he multiband MS shall meet all requirements specified for each individual band supported. In addition it shall meet the extra functional requirements for the multiband MSs. 2.2 Frequency bands of operation Multiband operation shall be possible with any combination of the frequency bands specified in

30、 the GSM specifications. No frequency band is treated as a primary band in the specification. The operators may however use control mechanisms to make the MSs treat one of the bands with priority. As a first implementation of Multiband operation only operation with GSM 900 (Standard or Extended) and

31、 DCS 1 800 is included in the standard. The proposed procedures shall however make it possible for operation between other bands if such are included in the core specifications in the future. 2.3 Backwards compatibility Backwards compatibility with phase 1 and phase 2 single band mobiles shall be en

32、sured by the specification of multiband operation. A multiband PLMN shall therefore, in addition to support of multiband MSs, be able to support the use of single band mobiles for, at least one of the bands of operation. ETSI ETSI TR 143 026 V13.0.0 (2016-01)63GPP TR 43.026 version 13.0.0 Release 13

33、Backwards compatibility by the multiband MSs shall also be ensured. The MSs shall therefore be able to, functionally, work as single band mobiles in a single band network. 2.4 PLMN codes Multiband operation of GSM/DCS by a single operator, with handover and assignment between the bands, implies that

34、 only one PLMN code is used in all bands of operation. Handover or assignment between PLMNs is not covered by this document or the work item. An operator, with license in more than one band, may however support multiband mobiles without handover and assignment between the bands. If so, more than one

35、 PLMN code may be used. This is already covered with the phase 1 and phase 2 specifications. 2.5 Other systems Multiband operation by a single operator does not include multi mode operation, i.e. handover, assignment or roaming between GSM/DCS and systems covered by other specifications or standards

36、. The amendments of the GSM/DCS specifications for multiband operation may however be done in a flexible way so that multi mode operation can make use of the same procedures. 3 Requirements 3.1 User requirements No special actions by the user shall be necessary to use a multiband MS. The possibility

37、 for the user to decide to operate the MS in a single band mode may however be supported. Indications may also be given to the user of which band is being used. The user of a multiband MS shall be able to roam between PLMNs operating in any of the MSs frequency bands of operation. The MS shall there

38、fore, at PLMN selection, present all available PLMNs within its frequency bands of operation. 3.2 Operator requirements The use of multiband operation shall be optional for the operator. Multiband MSs must therefore be able to, functionally, work as single band MSs in a single band network. When mul

39、tiband operation is used, it shall be possible to provide coverage in one frequency band independently of the coverage in another band Two options can be implemented by an operator when operating a multiband network : i) a BCCH in each band of operation; ii) a common BCCH in only one of the band of

40、operation when resources across all bands are co-located and synchronized. NOTE: For case ii), in order to ensure proper operation of the network, the operator should take into account issues related to the difference of propagation between the different bands, e.g GSM and DCS when performing cell p

41、lanning. As far as synchronization issues are concerned, the requirements for TA for multiband BTSs may only be fulfilled when the TA is the same in the two bands, i.e. within the tolerance as defined in GSM 05.10. This imposes some restrictions on the cells where the two bands are supported (e.g. s

42、mall cells). ETSI ETSI TR 143 026 V13.0.0 (2016-01)73GPP TR 43.026 version 13.0.0 Release 133.3 Radio requirements The radio requirements for GSM and DCS in the present GSM/DCS specification differs in some cases. A multiband MS and the multiband network shall meet all requirements for each band of

43、operation respectively. Type approval of multiband MSs will be covered by the respective test specifications and some additional tests for the multiband functionality. 3.4 Relation to frequency hopping The multiband MS and the multiband network shall support frequency hopping within each band of ope

44、ration. Frequency hopping between the bands of operation is not required. 4 Functional description To understand the necessary amendments of the phase 2 specifications functional descriptions of different procedures and solutions are described below. The technical realization are described in clause

45、 5 and the actual amendments are listed in annex 1 with a brief description. 4.1 Idle mode procedures The idle mode procedures will not be different for multiband MSs or networks. Only the fact that more than one band is available has to be taken into account. 4.1.1 PLMN selection A multiband MS sha

46、ll use the normal PLMN selection procedures, as specified in GSM 02.11 and 03.22, with the additional requirement to select from all available PLMNs in all bands of operation. When presenting available PLMNs it shall show all available PLMNs within the MSs bands of operation. A multiband PLMN may ha

47、ve BCCHs available on more than one band but shall still be treated as one PLMN and must therefore only be presented once. PLMN search time, at switch on, will be the sum of the search times presently specified for each band of operation if no prior knowledge is stored in the MS. 4.1.2 Cell re-selec

48、tion The multiband network will send out neighbour cell lists which may contain a mixture of channels from different frequency bands. The multiband MSs shall follow the normal cell-re-selection procedures with the addition to monitor all channels within the neighbour cell list which are within the M

49、Ss bands of operation. All MSs shall ignore channel numbers which are outside its bands of operation. Channels within the MSs bands of operation shall be monitored. Priority at cell re-selection can be given to one of the bands of operation by using existing phase 2 parameters. Compatibility with phase 1 and phase 2 MSs will be ensured by the procedures described in clause 6. 4.1.3 Location areas No special requirements are specified for the allocation of location areas among the cells in a multiband network. It shall therefore be possible the use the same or different lo