ETSI TS 100 394-4-6-2000 Terrestrial Trunked Radio (TETRA) Conformance Testing Specification Part 4 Protocol Testing Specification for Direct Mode Operation (DMO) Sub-Part 6 Abstra.pdf

1、- c PLEASE NOTE This document is normally accompanied by a disk/dish wnen purchased in hardcopy. The dislddisks contain information which would be of no value as a hardcopy document. If you require a copy of the diskldisb, please use the contact information below for your request. When submitting yo

2、ur request, please have the following irzfonnation vuiizble: Your company name/account number Originating orsanisacion Document number USMCanada Enformation Handling Services E-mail Te!: 800-U$-3352 Outside USAiCanada Except the United I(ingdom) Information Handling Services E-mai Te!: i 1-303-790

3、-0600 Technic3 Tz!: (O Fax: (O United Kingdom Indexes Ltd 344) 404409, Custoinet Support 34.1) 40442 I, Ccistoiner Suppori In formation Handing Senices and Teclinicai Indexer - Cortitiziad to Service Excellence ETSI TS 100 394-4-6 1.1.1 (2000-11) Technical Specification Terrestrial Trunked Radio (TE

4、TRA); Conformance testing specification; Part 4: Protocol testing specification for Direct Mode Operation (DMO); Sub-part 6: Abstract Test Suite (ATS) for Direct Mode Repeater (DM-REP) type 1 2 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) Th Reference DTSITETRA-02009-4-6 Keywords TETRA, DMO, protocol, tes

5、ting, TCN, ATS, radio ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of th

6、e present document can be downloaded from: http:/iwww. etsi I oq present document may be made available in more than one electronic version or in print. I any cas Df existing perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case

7、of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and

8、other ETSI documents is available at If you find errors in the present document, send your comment to: editor etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. 8 Europe

9、an Telecommunications Standards Institute 2000. All rights reserved. ETSI 3 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) Contents Intellectual Property Rights 5 Foreword 5 1 2 3 3.1 3.2 3.3 3.4 4 4.1 4.1.1 4.1.2 4.1.3 4.1.4 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.3 5 5.1 5.1.1 Scope 6 References 6 Definitions and a

10、bbreviations 7 TETRA definitions 7 TETRA abbreviations 7 IS0 9646 definitions 7 IS0 9646 abbreviations . 7 Abstract Test Method (ATM) 8 Single PCO testing 8 Upper Tester (UT) 8 Point of Control and Observation (PCO) . 9 Multiple PCO testing . 9 Upper Tester (UT) 9 Point of Control and Observation (P

11、CO) . 9 Test configurations and use of concurrent TTCN . 10 ATS conventions 11 Lower Tester (LT) 8 Test Coordination Procedures (TCP) 8 Lower Testers (LT) 9 Test Coordination Procedures (TCP) 9 5.1.1.1 5.1.1.2 5.1.1.3 5.1.1.4 5.1.1.5 5.1.1.6 5.1.1.7 5.1.1.8 5.1.1.9 5.1.1.10 5.1.1.11 5.1.1.12 5.1.2 5

12、.1.3 5.1.3.1 5.1.3.2 5.1.3.3 5.2 5.3 Naming conventions 11 Declarations part 11 Test suite type and structured type definitions . 11 Test suite operations definitions 11 Test case selection expression definitions 11 Test suite parameter declarations . 11 Test suite constant declarations . 12 Test su

13、ite variable declarations 12 Test case variable declarations 12 PCO declarations 12 Timer declarations 12 ASP type definitions . 12 PDU type definitions 13 Alias definitions . 13 Constraints part 13 Test case identifier 14 Test step identifier 14 Dynamic part . 14 Default identifier 14 Implementatio

14、n conventions 14 TC and TP naming 14 ETSI 4 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) Annex A (normative): A.l A.2 ATS for DMO Repeater type 1 (DM-REP1) MAC layer 15 The TTCN Graphical form (TTCN.GR) 15 The TTCN Machine Processable form (TTCN.MP) 15 Annex B (normative): B . 1 B.2 ATS summary 16 Partial

15、 PIXIT proforma for TETRA DMO Repeater type 1 MAC layer protocol . 16 Identification summary . 16 B.3 Test laboratory 16 B.4 Client identification 16 B.5 SUT 17 B.6 Protocol layer information 17 B.6.1 Protocol identification . 17 B.6.2 IUT information 17 B.6.2.1 Implicit send events . 17 B.6.2.2 Par

16、ameter values 17 Annex C (normative): C . 1 C.l.l C . 1.2 C.1.3 Testing environment 18 C.1.4 C.1.5 Comments . 19 C.2 C.3 C.4 C.5 Static conformance review report 20 C.6 Test campaign report 20 C.7 Observations . 21 Protocol Conformance Test Report (PCTR) proforma for TETRA DMO Repeater type 1 MAC la

17、yer protocol 18 Identification summary . 18 Protocol conformance test report 18 IUT identification 18 Limits and reservation . 19 IUT conformance status 19 Static conformance summary 19 Dynamic conformance summary . 19 History . 22 ETSI 5 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) Intellectual Property

18、Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 314: “Intellectual Property Rights (IPRs); Essent

19、ial, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server -). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaran

20、tee can be given as to the existence of other IPRs not referenced in ETSI SR O00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Terrestrial Trunked Radio

21、(TETRA). The present document consists of the following parts: Part 1: “Radio“; Part 2: Part 4: Part 5: “Security“. “Protocol testing specification for Voice plus Data (V+D)“; “Protocol testing specification for Direct Mode Operation (DMO)“; ETSI 6 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) 1 Scope The

22、present document contains the Abstract Test Suite (ATS) to test the TETRA Direct Mode Operation (DMO) Repeater type 1 (DM-REP1) protocol at layer 2, the Medium Access Control (MAC) protocol. The MAC protocol is specified in ETS 300 396-3 i and in EN 300 396-4 2. The Test Suite Structure (TSS) and Te

23、st Purposes (TPs) for this ATS are defined in EN 300 394-4-4 4. The objective of this test specification is to provide a basis for approval tests for TETRA equipment giving a high probability of air interface inter-operability between different manufacturers TETRA equipment. The IS0 standard for the

24、 methodology of conformance testing, ISO/IEC 9646-1 5, ISO/IEC 9646-2 6, ISO/IEC 9646-3 7 and ISO/IEC 9646-5 SI, as well as the ETSI rules for conformance testing, ETS 300 406 9 and ETR 141 lo are used as a basis for the test methodology. Annex A provides the Tree and Tabular Combined Notation (TTCN

25、) part of this ATS. Annex B provides the partial Protocol Implementation extra Information for Testing (PIXIT) Proforma of this ATS. Annex C provides the Protocol Conformance Test Report (PCTR) Proforma of this ATS. 2 References The following documents contain provisions which, through reference in

26、this text, constitute provisions of the present documen t. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies.

27、u1 ETSI ETS 300 396-3: “Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“. ETSI EN 300 396-4: “Radio Equipment and Systems (RES); Trans-European Trunked Radio (TETRA); Direct Mode (

28、DM); Part 4: Type 1 Repeater Air Interface“. ETSI EN 300 396-8-2: “Radio Equipment and Systems (RES); Trans-European Trunked RAdio (TETRA); Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Part 8-2: Type 1 repeater Air Interface“. ETSI

29、 EN 300 394-4-4: “Radio Equipment and Systems (RES); Trans-European Trunked RAdio (TETRA) system; Direct Mode Operation (DMO); Part 4: Protocol testing specification; Test Suite Structure and Test Purposes; Part 4-4 Repeater type 1 (DM REP1) Air Interface (AI)“. ISO/IEC 9646-1 (1994): “Information t

30、echnology - Open Systems Interconnection - Conformance Testing Methodology and Framework - Part 1: General Concepts“. (See also ITU-T Recommendation X.290 (1991). ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnection - Conformance Testing Methodology and Framework - Part 2: A

31、bstract Test Suite Specification“. (See also ITU-T Recommendation X.291 (1991). ISO/IEC 9646-3 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 3: The tree and tabular combined notation“. (See also ITU-T Recommendation X.292 (1992)

32、. 121 131 141 151 161 171 ETSI 7 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) 181 ISO/IEC 9646-5 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 5: Requirements on test laboratories and clients for the conformance assessment process“. (

33、See also ITU-T Recommendation X.292 (1992). ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. ETSI ETR 141: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing spec

34、ifications; The Tree and Tabular Combined Notation (TTCN) style guide“. 191 u01 3 Definitions and abbreviations 3.1 TETRA d ef i nit ions For the purposes of the present document, the terms and definitions given in EN 300 396-4 2 apply. 3.2 TETRA abbreviations For the purposes of the present documen

35、t the following TETRA abbreviations apply: DM-REP1 MAC Medium Access Control MS Mobile Station SDS Short Data Service SDU Service Data Unit Direct Mode Repeater Type 1 3.3 IS0 9646 definitions For the purposes of the present document the following ISOAEC 9646 definitions apply: TTCN.GR TTCN.MP PCTR

36、Protocol Conformance Test Report (PCTR proforma) 3.4 IS0 9646 abbreviations For the purposes of the present document the following ISOAEC 9646-1 5 abbreviations apply: ASP ATM ATS ICs IUT IXIT LT PCO PCTR PDU PICS PIXIT SAP SPyT SUT TC TP TSS TTCN Abstract Service Primitive Abstract Test Method Abst

37、ract Test Suite Implementation Conformance Statement Implementation Under Test Implementation extra Information for Testing Lower Tester Point of Control and Observation Protocol Conformance Test Report Protocol Data Unit Protocol Implementation Conformance Statements Protocol Implementation extra I

38、nformation for Testing Service Access Point Single Party Testing System Under Test Test Case Test Purpose Test Suite Structure Tree and Tabular Combined Notation ETSI 8 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) UT Upper Tester 4 Abstract Test Method (ATM) This clause describes the ATM used for testing

39、the DM-REP1 MAC layer protocol. The selected method is the remote method, as defined in ISO/IEC 9646-2 6, clause 11. This test method has been selected, because: - this test method implies no specific requirements from the Implementation Under Test (IUT); - - the upper Service Access Point (SAP) of

40、the IUT cannot be directly observed; the variety of the possible TETRA implementations is a serious technical obstacle for the adoption of a different ATM; - this test method places minimum limitations in the realization of conformance testing. The DM-REP1 MAC protocol defines the operation of a DM-

41、REP1 serving two air interfaces, the master and the slave link. To test the repeater operation in some cases both interfaces need to be controlled and observed simultaneously. This implies that two testing methods are used: the remote single-party test method (with one PCO) and the remote multiparty

42、 test method with two PCOs. 4.1 Single PCO testing The remote Single Party test method with a single PCO is illustrated in figure 1. layers Figure 1 : Remote SPyT test method for TETRA DM-REP1 MAC layer 4.1 .I Lower Tester (LT) A LT is located in a remote TETRA test system. It controls and observes

43、the behaviour of the IUT. 4.1.2 Upper Tester (UT) There is no explicit UT in the remote test method, but the DM-REP1 MAC layer and the layers above inside the System Under Test (SUT) are used implicitly for testing the MAC layer. 4.1.3 Test Coordination Procedures (TCP) The implicit send events defi

44、ned by the provider of an implementation in annex B serve the purpose of the TCP. They are used as an input to the IUT communicating with the UT to initiate test events at the DMO MAC layer. ETSI 9 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) 4.1.4 Point of Control and Observation (PCO) All test events at

45、 the PCO carrying service user data are specified in terms of MAC layer PDUs. Only few Abstract Service Primitives (ASPS) are defined for control or observation purposes. The mapping of the MAC PDUs into the physical layer frame structure is left to the test implementation. 4.2 Multiple PCO testing

46、The selected test method is illustrated in figure 2. 4.2.1 LOWER TESTER CONTROL FUNCTION cpli 1 TCP - PCOI u ASPs , ! Upperlayers TCP MAC- PDUS TETRA physical layer and radio communication Test system pcoi#Am Figure 2: Remote multi party test method for TETRA DM-REP1 MAC protocol Lower Testers (LT)

47、Two LTs: LT1 and LT2 are located in a remote TETRA test system. They observe the behaviour of the IUT. They are controlled and synchronized by the lower tester control function. 4.2.2 Upper Tester (UT) There is no explicit UT in the remote test method, but the layers above inside the System Under Te

48、st (SUT) are used implicitly for testing the DM-REP1 MAC layer. 4.2.3 Test Coordination Procedures (TCP) The implicit send events defined by the provider of an implementation in annex B serve the purpose of the TCP. They are used as an input to the IUT communicating with the UT to initiate test even

49、ts at the MAC protocol layer. 4.2.4 Point of Control and Observation (PCO) The PCOs are located inside the protocol. All test events at the PCOs carrying service user data are specified in terms of MAC PDUs. The mapping of the PDUs to possible physical layer service primitives is left to the test implementation. ETSI 10 ETSI TS 1 O0 394-4-6 V1.l.l (2000-1 1) Test configurations and use of concurrent TTCN As this ATS covers both single-party testing using non-concurrent TTCN, and multi-party testing using concurrent TT