ETSI TS 100 396-8-2-2000 Terrestrial Trunked Radio (TETRA) Technical Requirements for Direct Mode Operation (DMO) Part 8 Protocol Implementation Conformance Statement (PICS) Profor.pdf

1、ETSI TS 100 396-8-2 1.1.1 (2000-10) Technical Specification Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Sub-part 2: Type 1 repeater Air Interface (AI) 2 ETSI TS 1 O0 39

2、6-8-2 V1.l.l (2000-1 O) The pre Reference DTS/TETRA-02007-8-2 Keywords ICs, PICS, TETRA, DMO, radio ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 0001 7 - NAF 742 C Association but non lucratif enregistre la So

3、us-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.orq ent document may be made available in more than one electronic version or in print. In e of existing or perceived difference in contents between such versions,

4、 the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revisi

5、on or change of status. Information on the current status of this and other ETSI documents is available at http:/www.etsi.orq/tb/status/ If you find errors in the present document, send your comment to: editor et.si.fr Copyright Notification No part may be reproduced except as authorized by written

6、permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2000. All rights reserved. ETSI 3 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) Contents Intellectual Property Rights 5 Foreword . 5 Introduction 5 1 Scope 6 2 Refe

7、rences 6 3 Definitions and abbreviations . 7 3.1 Definitions 7 3.2 Abbreviations . 7 Conformance to this PICS proforma specification . 7 4 Annex A (normative): Protocol ICs proforma (PICS) for EN 300 396-4 . 8 . A . 1 Guidance for completing the PICS proforma 8 A . 1.1 Purposes and structure 8 A.1.2

8、 Abbreviations and conventions 8 A.1.3 Instructions for completing the PICS proforma 10 A.2 A.2.1 A.2.2 A.2.3 System Under Test (SUT) identification 11 A.2.4 Product supplier 11 A.2.5 Client (if different from product supplier) 11 A.2.6 PICS contact person . 12 A.3 Identification of the Protocol 12

9、A.4 AS Roles . 12 A.6 A.6.1 A.6.1.1 A.6.1.2 A.6.1.3 A.6.1.4 A.6.1.5 A.6.1.6 A.6.1.7 Data transmission 16 A.6.1.8 A.6.1.9 DMCC PDUs 17 A.6.1.10 DMCC constants . 19 A.6.2 A.6.2.1 A.6.2.3 A.6.2.4 A.6.2.5 A.6.2.6 Identification of the implementation 10 Date of the statement 10 Implementation Under Test

10、(IUT) identification . 10 Global statement of conformance . 12 Protocols for DM-MS supporting operation with a type 1 DM-REP (MS-REP1) . 13 DMCC major capabilities . 13 Circuit mode call Set-up 14 Circuit mode services offered . 14 Short data services 15 Type of short data service . 15 SDS user defi

11、ned data . 17 A.6.1.11 DMCC timers 20 MS-REP1 Data link layer (DLL) at Layer 2 20 MS-REP1 MAC features 20 A.6.2.2 MS-REP1-MAC procedures . 21 MS-REP1 MAC PDUs . 25 MS-REP1 MAC generated messages . 26 MS-REP1 MAC constants 26 Type 1 DM-REP Protocol 29 DM-REP1 Data link layer (DLL) at Layer 2 29 A.7.1

12、.1 Major services . 29 DM-REP1 MAC features 29 MS-REP1 Direct Mode Call Control (DMCC) at Layer 3 . 13 Circuit mode call . 13 MS-REP1 MAC timers . 28 A.7 A.7.1 A.7.1.2 ETSI A.7. A.7. A.7. 4 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) . 3 DM-REP1 MAC procedures . 30 . 5 DM-REP1 MAC generated messages . 32

13、 A.7.1.6 DM-REP1 MAC constants . 32 A.7.1.7 DM-REP1 MAC timers 33 A.8. PDU parameters for MS-REP1 and DM-REP1 used in DMCC at layer 3 and DLL at layer 2 . 34 . 4 DM-REP1 MAC PDUS . 32 A.8.1 A.8.1.1 A.8.1.2 A.8.1.3 A.8.1.4 A.8.1.5 A.8.1.6 A.8.1.7 A.8.1.8 A.8.1.9 A.8.1.10 A.8.1.11 A.8.1.12 A.8.1.13 A.

14、8.1.14 A.8.1.15 A.8.1.16 A.8.1.17 A.8.2 A.8.2.1 A.8.2.2 A.8.2.3 A.8.2.4 A.8.2.5 A.8.2.6 A.8.3 A.8.3.1 A.8.3.2 A.8.3.3 A.8.3.4 MS-REP1 PDU parameters for DMCC at layer 3 34 DM-SETUP 34 DM-SETUP PRES 35 DM-CONNECT 35 DM-DISCONNECT . 35 DM-CONNECT ACK 36 DM-OCCUPIED . 36 DM-RELEASE . 36 DM-TX CEASED .

15、37 DM-TX REQUEST 37 DM-TX ACCEPT . 37 DM-PREEMPT . 37 DM-PRE ACCEPT . 38 DM-REJECT 38 DM-INFO . 38 DM-SDS UDATA 39 DM-SDS DATA . 39 DM-SDS ACK 40 MS-REP1 and DM-REP1 PDU parameters for DLL at layer 2 . 40 DMAC-SYNC in SCH/S 40 DPRES-SYNC PDU . 41 DMAC-DATA 42 DMAC-FRAG 42 DMAC-END . 42 DMAC-U SIGNAL

16、 . 43 DM-MAC generated message parameters 43 DM-RESERVED 43 DM-SDS OCCUPIED 43 DM-TIMING REQUEST . 43 DM-TIMING ACK . 43 History 44 ETSI 5 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETS

17、I. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Propero Rights (IPRs); Essential, or potentially Essential, IPRs notifed to ETSI in respect of ETSI standards“, which is availabl

18、e from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/www.etsi.ordipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00

19、 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document is part 8 of a multi-part deliverable covering the

20、 Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); as identified below: Part 1: “General network design“; Part 2: “Radio aspects“; Part 3: “Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“; Part 4: “Type 1 repeater air interface“; Part 5:

21、 “Gateway air interface“; Part 6: “Security“; Part 7: “Type 2 repeater air interface“; Part 8: “Protocol Implementation Conformance Statement (PICS) proforma specification“; Part 9: “Service and Description Language (SDL) model“; Part 10: “Managed Direct Mode Operation (DMO)“. Introduction To evalua

22、te conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance Statement (ICs). ETSI 6 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) 1

23、Scope The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for TETRA Direct Mode Operation (DMO) Mobile Stations (MS) connected to type 1 repeater (MS-REP1) and for TETRA Direct Mode Operation type 1 repeaters (DM-REP1) Air Interface (AI) protocol, defined

24、in EN 300 396-4 i in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 5 and ETS 300 406 3. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. Refe

25、rences are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. il ETSI EN 300 396-4: “Terrestrial Trunked Radio (TETRA); Techn

26、ical requirements for Direct Mode Operation (DMO); Part 4: Type 1 repeater air interface“. ETSI ETS 300 396-8- 1: “Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Sub-part

27、1: Mobile Station to Mobile Station (MS-MS) Air Interface (AI)“. ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications Standardization Methodology“. ISO/IEC 9646- 1 (1994): “Information technology - Open systems interconnection - Conf

28、ormance testing methodology and framework - Part 1: General concepts“. ISO/IEC 9646-7 (1995): “Information technology - Open systems interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. ETSI ETS 300 396-3 (1998): “Terrestrial Trunked Radio

29、 (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“. Pl 31 41 51 61 ETSI 7 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) 3 3.1 Definitions and abbreviations Definitions For the purposes of the present document, the

30、terms and definitions given in EN 300 396-4 i, ISO/IEC 9646-1 4, ISO/IEC 9646-7 5 and the following apply. Implementation Conformance Statement (ICs): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been imple

31、mented. The ICs can take several forms: protocol ICs, profile ICs, profile specific ICs, information object ICs, etc. ICs proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICs Protocol ICs (PICS): ICs for an implementation or system c

32、laimed to conform to a given protocol specification 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ICs Implementation Conformance Statement IUT Implementation Under Test PICS Protocol Implementation Conformance Statement SCS System Conformance Statemen

33、t SUT System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numberinghaming

34、and ordering of the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A. 1. ETSI 8 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) Annex A (normative): Protocol ICs proforma (PICS) for EN

35、300 396-4 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PIC

36、S. A.l Guidance for completing the PICS proforma A. 1 .I Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in EN 300 396-4 i may provide information about the implementation in a standardized manner.

37、 The PICS proforma is subdivided into clauses for the following categories of information: - - identification of the implementation; guidance for completing the PICS proforma; - global statement of conformance; - - - - DM-REP1 part (layer 2); - identification of the roles, MS-REP1 or DM-REP1; MS-REP

38、1 layer 3 protocol part; MS-REP1 layer 2 protocol part; PDU parameters at layer 3 and layer 2. A. 1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISODEC 9646-7 51. Item column The i

39、tem column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defi

40、ned in ISODEC 9646-7 5, are used for the status column: m O n/a X mandatory - the capability is required to be supported; optional - the capability may be supported or not; not applicable - in the given context, it is impossible to use the capability; prohibited (excluded) - there is a requirement n

41、ot to use this capability in the given context; ETSI 9 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) 0.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is define

42、d immediately following the table; conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table. ci Referen

43、ce column The reference column makes reference to EN 300 396-4 i, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 5, are used for the support column: Y or y

44、 N or n N/A, n/a or - supported by the implementation; not supported by the implementation; no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it

45、 is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at th

46、e bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE: ?3: IF prof1 THEN Y ELSE N It is also possible to provide a comment to an answer in the space provided at the bott

47、om of the table. NOTE: As stated in ISO/IEC 9646-7 5, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non- conformant. Support for a parameter on a PDU means that the semantics of that p

48、arameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notations are used: range of values: example: 5 20 list of values: , , , example: 2,4, 6, 8,9 example: 1 101B, 101 lB, 1 11 1B example: OAH,

49、34H, 2F“ list of named values: (), (), , ( example: reject(l), accept(2) length: size ( ) example: size (i 8) ETSI 10 ETSI TS 1 O0 396-8-2 V1.l.l (2000-1 O) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists, used, for example, in the conditional expressi