ETSI TS 100 927-2003 Digital cellular telecommunications system (Phase 2+) Numbering addressing and identification (3GPP TS 03 03 Version 7 8 0 Release 1998)《数字蜂窝通信系统(第2+阶段) 编号 寻址和.pdf

1、 ETSI TS 100 927 V7.8.0 (2003-09)Technical Specification Digital cellular telecommunications system (Phase 2+);Numbering, addressing and identification(3GPP TS 03.03 version 7.8.0 Release 1998)GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI TS 100 927 V7.8.0 (2003-09) 1 3GPP TS 03.03 version 7.8.0

2、 Release 1998 Reference RTS/TSGN-040303v780 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Importa

3、nt notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the P

4、ortable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Informa

5、tion on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The cop

6、yright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently

7、 being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 100 927 V7.8.0 (2003-09) 2 3GPP TS 03.03 version 7.8.0 Release 1998 Intellectual Property Rights IPRs essential or

8、potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essen

9、tial, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI.

10、No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnershi

11、p Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identit

12、ies can be found under http:/webapp.etsi.org/key/queryform.asp . ETSI ETSI TS 100 927 V7.8.0 (2003-09) 3 3GPP TS 03.03 version 7.8.0 Release 1998 Contents Intellectual Property Rights2 Foreword.2 Foreword.5 1 Scope 6 1.1 References 6 1.2 Abbreviations .7 1.3 General comments to references 7 1.4 Conv

13、entions on bitordering 7 2 Identification of mobile subscribers.8 2.1 General .8 2.2 Composition of IMSI8 2.3 Allocation principles 9 2.4 Structure of TMSI 9 2.5 Structure of LMSI 9 2.6 Structure of TLLI .9 3 Numbering plan for mobile stations.10 3.1 General .10 3.2 Numbering plan requirements 10 3.

14、3 Structure of MS international PSTN/ISDN number (MSISDN) 11 3.4 Mobile Station Roaming Number (MSRN) for PSTN/ISDN routeing.12 3.5 Structure of Mobile Station International Data Number 12 3.6 Handover Number 12 3.7 Structure of an IP v4 address12 3.8 Structure of an IP v6 address12 4 Identification

15、 of location areas and base stations.12 4.1 Composition of the Location Area Identification (LAI).12 4.2 Composition of the Routing Area Identification (RAI)13 4.3 Base station identification 13 4.3.1 Cell Identity (CI) and Cell Global Identification (CGI)13 4.3.2 Base Station Identify Code (BSIC).1

16、4 4.4 Regional Subscription Zone Identity (RSZI)14 4.5 Location Number15 5 Identification of MSCs and location registers15 5.1 Identification for routing purpose.15 5.2 Identification of HLR for HLR restoration application16 6 International Mobile Station Equipment Identity and Software Version Numb

17、er.16 6.1 General .16 6.2 Composition of IMEI and IMEISV16 6.2.1 Composition of IMEI16 6.2.2 Composition of IMEISV.17 6.3 Allocation principles 17 7 Identification of Voice Group Call and Voice Broadcast Call Entities17 7.1 Group Identities17 7.2 Group Call Area Identification.18 7.3 Voice Group Cal

18、l and Voice Broadcast Call References .18 8 SCCP subsystem numbers18 8.1 Globally standardised subsystem numbers used for GSM .19 8.2 National network subsystem numbers used for GSM 19 9 Definition of Access Point Name.19 9.1 Structure of APN19 ETSI ETSI TS 100 927 V7.8.0 (2003-09) 4 3GPP TS 03.03 v

19、ersion 7.8.0 Release 1998 9.1.1 Format of APN Network Identifier.20 9.1.2 Format of APN Operator Identifier.20 9.2 Definition of the Wild Card APN.20 9.2.1 Coding of the Wild Card APN21 10 Identification of the Cordless Telephony System entities21 10.1 General description of CTS-MS and CTS-FP Identi

20、ties 21 10.2 CTS Mobile Subscriber Identities 21 10.2.1 General21 10.2.2 Composition of the CTSMSI 21 10.2.3 Allocation principles.21 10.2.4 CTSMSI hexadecimal representation .22 10.3 Fixed Part Beacon Identity.22 10.3.1 General22 10.3.2 Composition of the FPBI 22 10.3.2.1 FPBI general structure.22

21、10.3.2.2 FPBI class A23 10.3.2.3 FPBI class B23 10.3.3 Allocation principles.23 10.4 International Fixed Part Equipment Identity 23 10.4.1 General23 10.4.2 Composition of the IFPEI.24 10.4.3 Allocation principles.24 10.5 International Fixed Part Subscription Identity24 10.5.1 General24 10.5.2 Compos

22、ition of the IFPSI .24 10.5.3 Allocation principles.25 11 Identification of Localised Service Area25 Annex A (informative): Colour Codes26 A.1 Utilisation of the BSIC.26 A.2 Guidance for planning26 A.3 Example of PLMN Colour Codes (NCCs) for the European region27 Annex B (informative): Change histor

23、y .28 History 29 ETSI ETSI TS 100 927 V7.8.0 (2003-09) 5 3GPP TS 03.03 version 7.8.0 Release 1998 Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change

24、 following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 present

25、ed to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in th

26、e document. ETSI ETSI TS 100 927 V7.8.0 (2003-09) 6 3GPP TS 03.03 version 7.8.0 Release 1998 1 Scope The present document defines: a) an identification plan for mobile subscribers in the GSM system; b) principles of assigning telephone and ISDN numbers to MSs in the country of registration of the MS

27、; c) principles of assigning Mobile Station (MS) roaming numbers to visiting MSs; d) an identification plan for location areas, routing areas, and base stations in the GSM system; e) an identification plan for MSCs, SGSNs, GGSNs, and location registers in the GSM system; f) principles of assigning i

28、nternational mobile equipment identities; g) principles of assigning zones for regional subscription; h) an identification plan for groups of subscribers to the Voice Group Call Service (VGCS) and to the Voice Broadcast Service (VBS); and identification plan for voice group calls and voice broadcast

29、 calls; an identification plan for group call areas; i) principles for assigning Packet Data Protocol (PDP) addresses to mobile stations; j) an identification plan for point-to-multipoint data transmission groups. 1.1 References The following documents contain provisions which, through reference in

30、this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. I

31、n the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 GSM 01.04: “Digital cellular telecommunications system (Phase 2+); Abbreviations and acronyms“. 2

32、GSM 03.08: “Digital cellular telecommunications system (Phase 2+); Organization of subscriber data“. 3 GSM 03.20: “Digital cellular telecommunications system (Phase 2+); Security related network functions“. 4 Void 5 GSM 03.70: “Digital cellular telecommunications system (Phase 2+); Routeing of calls

33、 to/from Public Data Networks (PDN)“. 6 GSM 04.08: “Digital cellular telecommunications system (Phase 2+); Mobile radio interface layer 3 specification“. 7 GSM 09.03: “Digital cellular telecommunications system (Phase 2+); Signalling requirements on interworking between the Integrated Services Digit

34、al Network (ISDN) or Public Switched Telephone Network (PSTN) and the Public Land Mobile Network (PLMN)“. ETSI ETSI TS 100 927 V7.8.0 (2003-09) 7 3GPP TS 03.03 version 7.8.0 Release 1998 8 GSM 09.60: “Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); GPRS Tu

35、nnelling Protocol (GTP) across the Gn and Gp Interface“. 9 GSM 11.11: “Digital cellular telecommunications system (Phase 2+); Specification of the Subscriber Identity Module - Mobile Equipment (SIM - ME) interface“. 10 CCITT Recommendation E.164: “Numbering plan for the ISDN era“. 11 CCITT Recommend

36、ation E.212: “Identification plan for land MSs“. 12 CCITT Recommendation E.213: “Telephone and ISDN numbering plan for land MSs in public land mobile networks (PLMN)“. 13 CCITT Recommendation X.121: “International numbering plan for public data networks“. 14 RFC 791: “Internet Protocol“. 15 RFC 1883

37、: “Internet Protocol, Version 6 (IPv6) Specification“. 16 GSM 04.68 (ETS 100 948): “Group Call Control (GCC) protocol“. 17 GSM 04.69 (ETS 100 949): “Broadcast Call Control (BCC) Protocol “. 18 GSM 09.02: “Mobile Application Part (MAP) specification“. 1.2 Abbreviations Abbreviations used in the prese

38、nt document are listed in GSM 01.04. 1.3 General comments to references The identification plan for mobile subscribers defined below is that defined in CCITT Recommendation E.212. The ISDN numbering plan for MSs and the allocation of mobile station roaming numbers is that defined in CCITT Recommenda

39、tion E.213. Only one of the principles for allocating ISDN numbers is proposed for GSM PLMNs. Only the method for allocating MS roaming numbers contained in the main text of CCITT Recommendation E.213 is recommended for use in GSM PLMNs. If there is any difference between this Technical Specificatio

40、n and the CCITT Recommendations, the former shall prevail. For terminology, see also CCITT Recommendations E.164 and X.121. 1.4 Conventions on bitordering The following conventions hold for the coding of the different identities appearing in this Technical Specification and in other GSM Technical Sp

41、ecifications if not indicated otherwise: - the different parts of an identity are shown in the figures in order of significance; - the most significant part of an identity is on the left part of the figure and the least significant on the right. When an identity appears in other Technical Specificat

42、ions, the following conventions hold if not indicated otherwise: - digits are numbered by order of significance, with digit 1 being the most significant; - bits are numbered by order of significance, with the lowest bit number corresponding to the least significant bit. ETSI ETSI TS 100 927 V7.8.0 (

43、2003-09) 8 3GPP TS 03.03 version 7.8.0 Release 1998 2 Identification of mobile subscribers 2.1 General A unique International Mobile Subscriber Identity (IMSI) shall be allocated to each mobile subscriber in the GSM system. NOTE: This IMSI is the concept referred to by CCITT as “International Mobile

44、 Station Identity“. In order to support the subscriber identity confidentiality service the VLRs and SGSNs may allocate Temporary Mobile Subscriber Identities (TMSI) to visiting mobile subscribers. The VLR and SGSNs must be capable of correlating an allocated TMSI with the IMSI of the MS to which it

45、 is allocated. An MS may be allocated two TMSIs, one for services provided through the MSC, and the other for services provided through the SGSN (P-TMSI for short). For addressing on resources used for GPRS, a Temporary Logical Link Identity (TLLI) is used. The TLLI to use is built by the MS either

46、on the basis of the P-TMSI (local or foreign TLLI), or directly (random TLLI). In order to speed up the search for subscriber data in the VLR a supplementary Local Mobile Station Identity (LMSI) is defined. The LMSI may be allocated by the VLR at location updating and is sent to the HLR together wit

47、h the IMSI. The HLR makes no use of it but includes it together with the IMSI in all messages sent to the VLR concerning that MS. 2.2 Composition of IMSI IMSI is composed as shown in figure 1. MCCNot more than 15 digits3 digits 2 or 3 digitsMNC MSINNMSIIMSIFigure 1: Structure of IMSI IMSI is compose

48、d of three parts: i) Mobile Country Code (MCC) consisting of three digits. The MCC identifies uniquely the country of domicile of the mobile subscriber; ii) Mobile Network Code (MNC) consisting of two or three digits for GSM applications. The MNC identifies the home GSM PLMN of the mobile subscriber

49、. The length of the MNC (two or three digits) depends on the value of the MCC. A mixture of two and three digit MNC codes within a single MCC area is not recommended and is outside the scope of this specification. iii) Mobile Subscriber Identification Number (MSIN), identifying the mobile subscriber within a GSM PLMN. The National Mobile Subscriber Identity (NMSI) consists of the Mobile Network Code and the Mobile Subscriber Identification Number. ETSI ETSI TS 100 927 V7.8.0 (2003-09) 9 3GPP TS 03.03 version 7.8.0 Release 1998 2.3 Alloc