ETSI TS 101 570-2-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 2 Class A B _1.pdf

1、 ETSI TS 101 570-2 V1.1.1 (2012-06) Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 2: Class A/B Test Descriptions Technical Specification ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)2Reference DTS/ERM-TG26

2、-088-2 Keywords DSC, interoperability, maritime, TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no i

3、nvestigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Sp

4、ecification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.1. ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)51 Scope The

5、 present document contains the Test Descriptions (TD) for interoperability testing of the class A/B DSC radio equipment. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited ve

6、rsion applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks includ

7、ed in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 338-2: “Electromagnetic compatibility and Radio spectrum Matte

8、rs (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 2: Class A/B DSC“. 2.2 Informative references The following referenced documents are no

9、t necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 101 570-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digitial Selective Calling (DSC) Radios; Part 1: Re

10、quirements catalogue“. i.2 ETSI EN 300 338-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile

11、service; Part 1: Common requirements“. 3 Abbreviations For the purposes of the present document, the abbreviations given in EN 300 338-1 i.2 and the following apply: CF (Test) ConFiguration EUT Equipment Under Test NACK Negative Acknowledgement QE Qualified Equipment (i.e. DSC standards compliant) T

12、D Test Description TP Test Purpose TSS Test Suite Structure ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)64 Test Configurations This clause defines all test configurations used. Each test description refers to one or multiple test configurations. It is assumed that the initial state of all the equipment i

13、nvolved in the test configuration is standby, i.e. unless stated otherwise the pre-test conditions of each test description assume standby mode for the equipment. An arrow connection between devices indicates that these devices are in communication range, i.e. in CFG_6 EUT, QE1 and QE2 are all in th

14、e same communication range. However, QE3 is only in communication range with QE2. Figure 1: Configurations for VHF EUT ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)7Figure 2: Configurations for MF EUT ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)8Figure 3: Configurations for HF EUT ETSI ETSI TS 101 570-2 V1.1.1

15、 (2012-06)95 Test Suite Structure (TSS) The following table shows the Test Suite Structure contained in the present document. Each Test Sub-Group may contain more than one test. Test Group Test Sub-Group (sub-group ID) VHF Individual Calls (IC) Group Calls (GC) All Ships Calls (ASC) Sending Distress

16、 Alerts (SDA) Receiving Distress Alerts (RDA) Sending Distress Relays and Acknowledgements (SDRA) Other Calls (OC) Multiple automated procedures and parallel event handling (MAP) MF/HF Individual Calls (IC) Group Calls (GC) Geographic Area Calls (GAC) Sending Distress Alerts (SDA) Receiving Distress

17、 Alerts (RDA) Sending Distress Relays and Acknowledgements (SDRA) Other Calls (OC) Multiple automated procedures and parallel event handling (MAP) Interface and other functions (IF) General test (GEN) Alarms in standby mode (ASM) Alarms when busy (AWB) Standby mode interface functions (SMIF) Timeout

18、 interface functions (TIF) Each test description is described through a tabular format conforming to the following convention: Interoperability Test Description Identifier: A unique identifier. The test description identifiers are conforming to the TD_DSC_ naming convention, where: is the Test Group

19、 ID (VHF / MFHF) is the Test Sub-Group ID is the sequential number within the test sub-group Summary: Short description of the test objective Configuration: The relevant test configuration, referencing the test set configurations listed in the annex References: The reference indicates the clauses of

20、 the base standard specifications in which the related interoperability requirement is expressed. Pre-test conditions: Defines in which initial state the test equipment has to be to apply the actual test description Step Test Sequence Verdict Pass Fail 1 The description of the individual condition t

21、o verify or action to perform Yes/No criteria of the outcome of this verification step (if applicable) Yes/No criteria of the outcome of this verification step (if applicable) 2 Final verdict: ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)106 Test Descriptions (TD) VHF radios 6.1 Individual Calls Interoper

22、ability Test Description Identifier: TD_DSC_VHF_IC_0001 Summary: Sending Individual call - Routine Configuration: CF_1 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select

23、 Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:

24、16 Yes No 8 Cause QE1 to send ACK to EUT 9 Verify that EUT switches to the selected channel in step 4 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0002 Summary: Sending Individual call with NACK - Routine Confi

25、guration: CF_1 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intersh

26、ip Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause QE1 to send NACK to EUT 9 Verify that EUT does not switch to the selected channel in s

27、tep 4 Yes No 10 Verify that EUT indicates call failed or similar Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0003 Summary: Sending Individual call to a coast station - Routine Configuration: CF_2 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and

28、EUT in standby on CH:16 QE1 programmed with a Coast Station MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu does not propose a working channel Yes No Final verdict: ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)11

29、Interoperability Test Description Identifier: TD_DSC_VHF_IC_0004 Summary: Sending Individual call - Urgency Configuration: CF_2 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual -

30、 Urgency 2 Enter/select MMSI of QE1 3 Set the proposed channel to CH:72 4 Cause EUT to send the individual call to QE1 5 Verify that QE1 receives the call and displays the proposed channel Yes No6 Verify that QE1 sounds the Urgency alarm Yes No 7 Verify that QE1 displays the MMSI of QE1 Yes No 8 Ver

31、ify that EUT is still on CH:16 Yes No 9 Cause QE1 to send ACK to QE1 10 Verify that EUT switches to CH:72 Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0005 Summary: Sending Individual call with NACK - Urgency C

32、onfiguration: CF_2 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Urgency 2 Enter/select MMSI of QE1 3 Set the proposed channel to CH:72 4 Cause EUT to send the individual ca

33、ll to QE1 5 Verify that QE1 receives the call and displays the proposed channel Yes No6 Verify that QE1 sounds the Urgency alarm Yes No 7 Verify that QE1 displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause QE1 to send NACK to QE1 10 Verify that EUT stays on CH:16 Yes N

34、o Final verdict: ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)12Interoperability Test Description Identifier: TD_DSC_VHF_IC_0006 Summary: Sending Individual call - Safety Configuration: CF_2 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 Step Test Sequence Verdic

35、t Pass Fail 1 On EUT select Call then select Individual - Safety 2 Enter/select MMSI of QE1 3 Set the proposed channel to CH:72 4 Cause EUT to send the individual call to QE1 5 Verify that QE1 receives the call and displays the proposed channel Yes No6 Verify that QE1 sounds the Safety alarm Yes No

36、7 Verify that QE1 displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause QE1 to send ACK to QE1 10 Verify that EUT switches to CH:72 Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0007

37、 Summary: Sending Individual call with NACK - Safety Configuration: CF_2 References: 1, clause 6.6.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Safety 2 Enter/select MMSI of QE1 3 Set the proposed c

38、hannel to CH:72 4 Cause EUT to send the individual call to QE1 5 Verify that QE1 receives the call and displays the proposed channel Yes No6 Verify that QE1 sounds the Safety alarm Yes No 7 Verify that QE1 displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause QE1 to send

39、 NACK to QE1 10 Verify that EUT stays on CH:16 Yes No Final verdict: ETSI ETSI TS 101 570-2 V1.1.1 (2012-06)13Interoperability Test Description Identifier: TD_DSC_VHF_IC_0008 Summary: Receiving Individual call - Routine Configuration: CF_2 References: 1, clause 6.7.1, annex C Pre-test conditions: QE

40、1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the

41、 call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause EUT to send ACK to QE1 9 Verify that EUT switches to CH:72 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Te

42、st Description Identifier: TD_DSC_VHF_IC_0009 Summary: Receiving Individual call with NACK - Routine Configuration: CF_2 References: 1, clause 6.7.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 sele

43、ct Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is st

44、ill on CH:16 Yes No 8 Cause EUT to send NACK to QE1 9 Verify that EUT is still on CH:16 Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0010 Summary: Receiving Individual call when busy - Routine Configuration: CF_2 References: 1, clause 6.7.1, annex C Pre-test cond

45、itions: QE1 and EUT in individual call on CH:72 QE2 programmed with an individual MMSI of EUT Step Test Sequence Verdict Pass Fail 1 On QE2 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Cause QE2 to send the individual call to EUT 4 Verify that EUT sounds a self-terminati

46、ng alarm Yes No 5 Verify that EUT is still on CH:72 Yes No 6 Cause EUT to terminate the individual call 7 Verify that EUT displays that calls are on hold Yes No 8 On EUT enter the received call log and verify that the call from QE2 is logged Yes NoFinal verdict: ETSI ETSI TS 101 570-2 V1.1.1 (2012-0

47、6)14Interoperability Test Description Identifier: TD_DSC_VHF_IC_0011 Summary: Receiving Individual call - Urgency Configuration: CF_2 References: 1, clause 6.7.1, annex C Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail

48、1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Yes No 7 Verify t

49、hat EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send ACK to QE1 10 Verify that EUT switches to CH:72 Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0012 Summary: Receiving Individual call with NACK - Urgency Configuration: CF_2 References: 1, clause 6.7.1, annex C Pre-test conditions: QE1 and EUT in