ETSI TS 101 570-3-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 3 Class D Te_1.pdf

1、 ETSI TS 101 570-3 V1.1.1 (2012-06) Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 3: Class D Test Descriptions Technical Specification ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)2Reference DTS/ERM-TG26-0

2、88-3 Keywords DSC, interoperability, maritime, TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no inv

3、estigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Spec

4、ification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.1. ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)51 Scope The p

5、resent document contains the Test Descriptions (TD) for interoperability testing of the class D DSC radio equipment. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited versio

6、n applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included i

7、n this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 338-3: “Electromagnetic compatibility and Radio spectrum Matters (

8、ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 3: Class D DSC“. 2.2 Informative references The following referenced documents are not nece

9、ssary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 101 570-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 1: Requireme

10、nts catalogue“. i.2 ETSI EN 300 338-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service

11、; Part 1: Common requirements“. 3 Abbreviations For the purposes of the present document, the abbreviations given in EN 300 338-1 i.2 and the following apply: CF (Test) ConFiguration EUT Equipment Under Test TD Test Description TP Test Purpose TSS Test Suite Structure ETSI ETSI TS 101 570-3 V1.1.1 (

12、2012-06)64 Test Configurations This clause defines all test configurations used. Each test description refers to one or multiple test configurations. It is assumed that the initial state of all the equipment involved in the test configuration is standby, i.e. unless stated otherwise the pre-test con

13、ditions of each test description assume standby mode for the equipment. An arrow connection between devices indicates that these devices are in communication range, i.e. in CFG_6 EUT, QE1 and QE2 are all in the same communication range. However, QE3 is only in communication range with QE2. Class DEU

14、T QE1Class DCF_1Class D Class A VHFCF_2Class D Class B VHFCF_3Class D Class A/B VHFCF_4Class A/B VHFQE2QE2 is not in EUTscommunication rangeCF_5Class DClass A/B VHFClass DQE2 is within EUTscommunication rangeQE3CF_6Class DClass A/B VHFQE2 is within EUTscommunication rangeClass A/B VHF Class DFigure

15、1: Configurations for Class D EUT ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)75 Test Suite Structure (TSS) The following table shows the Test Suite Structure contained in the present document. Test Group Test Sub-Group (sub-group ID) VHF Individual Calls (IC) Group Calls (GC) All Ships Calls (ASC) Sendi

16、ng Distress Alerts (SDA) Receiving Distress Alerts (RDA) Non Distress Automated Procedures (NDAP) Other Calls (OC) Interface and Other Functions (IOF) General test (GEN) Alarms in standby mode (ASM) Alarms when busy (AWB) Standby mode interface functions (SMIF) Each test description is described thr

17、ough a tabular format conforming to the following convention: Interoperability Test Description Identifier: A unique identifier. The test description identifiers are conforming to the TD_DSC_ naming convention, where: is the Test Group ID (VHF / MFHF) is the Test Sub-Group ID is the sequential numbe

18、r within the test sub-group Summary: Short description of the test objective Configuration: The relevant test configuration, referencing the test set configurations listed in the Annex References: The reference indicates the clauses of the base standard specifications in which the related interopera

19、bility requirement is expressed Pre-test conditions: Defines in which initial state the test equipment has to be to apply the actual test description Step Test Sequence Verdict Pass Fail 1 The description of the individual condition to verify or action to perform Yes/No criteria of the outcome of th

20、is verification step (if applicable) Yes/No criteria of the outcome of this verification step (if applicable) 2 Final verdict: ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)86 Test Descriptions (TD) 6.1 Individual Calls Interoperability Test Description Identifier: TD_DSC_VHF_IC_0001 Summary: Sending Indiv

21、idual call - Routine Configuration: CF_1 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify t

22、hat menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause QE1 to send ACK to EUT 9 Verify that EUT switches to the s

23、elected channel in step 4 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0002 Summary: Sending Individual call with NACK - Routine Configuration: CF_1 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: Q

24、E1 and EUT in standby on CH:16 QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5

25、 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause QE1 to send NACK to EUT 9 Verify that EUT does not switch to the selected channel in step 4 Yes No 10 Verify that EUT indicates call failed or similar Yes No Fi

26、nal verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0003 Summary: Sending Individual call to a coast station - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with a Coast Station MMSI Step Te

27、st Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu does not propose a working channel Yes No Final verdict: ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)9Interoperability Test Description Identifier: TD_DSC_VHF_IC_0008 Summary:

28、 Receiving Individual call - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Routine 2 Enter/select MMSI o

29、f EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause EUT to send ACK to QE1 9 Verify th

30、at EUT switches to CH:72 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0009 Summary: Receiving Individual call with NACK - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions:

31、QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives t

32、he call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on CH:16 Yes No 8 Cause EUT to send NACK to QE1 9 Verify that EUT is still on CH:16 Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0010 Summ

33、ary: Receiving Individual call when busy - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in individual call on CH:72 QE2 programmed with an individual MMSI of EUT Step Test Sequence Verdict Pass Fail 1 On QE2 select Call then select Individual -

34、Routine 2 Enter/select MMSI of EUT 3 Cause QE2 to send the individual call to EUT 4 Verify that EUT sounds a self-terminating alarm Yes No 5 Verify that EUT is still on CH:72 Yes No 6 Cause EUT to terminate the individual call 7 Verify that EUT displays unread messages Yes No 8 On EUT select Call th

35、en Received Calls and Verify that the call from QE2 is logged Yes NoFinal verdict: ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)10Interoperability Test Description Identifier: TD_DSC_VHF_IC_0011 Summary: Receiving Individual call - Urgency Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-tes

36、t conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that

37、EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send ACK to QE1 10 Verify that EUT switches to CH:72 Yes No 11 Verify voice comm

38、unication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0012 Summary: Receiving Individual call with NACK - Urgency Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with

39、an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Ve

40、rify that EUT sounds the Urgency alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send NACK to QE1 10 Verify that EUT returns to standby on CH:16 Yes No Final verdict: ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)11Interoperability Te

41、st Description Identifier: TD_DSC_VHF_IC_0013 Summary: Receiving Individual call - Safety Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call t

42、hen select Individual - Safety 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call, sounds the Safety alarm and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify

43、 that EUT is still on CH:16 Yes No 8 Cause EUT to send ACK to QE1 9 Verify that EUT switches to CH:72 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0014 Summary: Receiving Individual call with NACK - Safety Conf

44、iguration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on CH:16 EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Safety 2 Enter/select MMSI of EUT 3 Set the proposed channel to CH:72

45、4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Safety alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on CH:16 Yes No 9 Cause EUT to send NACK to QE1 10

46、Verify that EUT returns to standby on CH:16 Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_VHF_IC_0015 Summary: Sending Individual call on a Distress channel Configuration: CF_2 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE

47、1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Enter a distress channel as working channel 5 Cause EUT to send the individual call to

48、QE1 6 Verify that EUT does not send the call and indicates a channel selection error Yes NoFinal verdict: ETSI ETSI TS 101 570-3 V1.1.1 (2012-06)126.2 Group Calls Interoperability Test Description Identifier: TD_DSC_VHF_GC_0001 Summary: Sending group call - Routine Configuration: CF_2 References: 1,

49、 clause 6.6.1 Pre-test conditions: QE1 and EUT in standby on CH:16 QE1 programmed with a group MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Group 2 Enter/select group MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the group call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT