ETSI TS 101 811-3-1-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the packet based convergence layer Part 3 IEEE 1394 Service Specific Converg.pdf

1、 ETSI TS 101 811-3-1 V1.3.1 (2004-08)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the packet based convergence layer;Part 3: IEEE 1394 Service Specific Convergence Sublayer (SSCS);Sub-part 1: Protocol Implementation ConformanceStatement (PICS

2、) proformaETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 2 Reference RTS/BRAN-0024TB4-3-1 Keywords access, HIPERLAN, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non l

3、ucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived differe

4、nce in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that

5、 the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/por

6、tal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUG

7、TESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational

8、 Partners. ETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 3 Contents Intellectual Property Rights4 Foreword.4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviations .6 4 Conformance to this PICS proforma specification.6 Annex A (normative): Protocol I

9、CS proforma for TS 101 493-3.7 A.1 Guidance for completing the PICS proforma.7 A.1.1 Purposes and structure7 A.1.2 Abbreviations and conventions 7 A.1.3 Instructions for completing the PICS proforma9 A.2 Identification of the implementation 9 A.2.1 Date of the statement9 A.2.2 Implementation Under T

10、est (IUT) identification .9 A.2.3 System Under Test (SUT) identification10 A.2.4 Product supplier10 A.2.5 Client (if different from product supplier)11 A.2.6 PICS contact person .11 A.3 Identification of the TS 101 493-3 .12 A.4 Global statement of conformance.12 A.5 Roles.12 A.6 PICS for Wireless T

11、erminal (WT) or Central Controller (CC) - user plane services.12 A.6.1 Major capabilities.12 A.6.1.1 Clock synchronization 13 A.6.1.2 Asynchronous transaction data transport 14 A.6.1.3 Isochronous stream data transport 15 A.6.1.4 Asynchronous stream data transport.16 A.6.2 PDU and Parameters 16 A.7

12、PICS for Wireless Terminal (WT) or Central Controller (CC) - control plane services18 A.7.1 Service Specific Convergence Sublayer procedures 18 A.7.2 SSCS_PDU description18 A.7.3 CL Information elements parameters .19 Annex B (informative): Bibliography.21 History 22 ETSI ETSI TS 101 811-3-1 V1.3.1

13、(2004-08) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellect

14、ual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigat

15、ion, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (T

16、S) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 3, sub-part 1 of a multi-part deliverable. Full details of the entire series can be found in part 1, sub-part 1 (see bibliography). Introduction To evaluate conformance of a particular implement

17、ation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called a Protocol Implementation Conformance Statement (PICS). ETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 5 1 Scope The present document provid

18、es the Protocol Implementation Conformance Statement (PICS) proforma for the Packet based Convergence Layer for HIPERLAN 2; Part 3: IEEE 1394 SSCS, as defined in TS 101 493-3 1 in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ET

19、S 300 406 2. It details in tabular form the implementation options, i.e. the optional functions additional to those which are mandatory to implement. 2 References The following documents contain provisions, which, through reference in this text, constitute provisions of the present document. Referen

20、ces are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available

21、in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 493-3 (V1.3.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Packet based Convergence Layer; Part 3: IEEE 1394 Service Specific Convergence Sublayer (SSCS)“. 2 ETSI ETS 300 406: “Methods for testin

22、g and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7: “Information techn

23、ology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 101 493-3 1, ISO/IEC 9646-1 3, ISO/IE

24、C 9646-7 4 and the following apply: ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given spec

25、ification, stating which capabilities have been implemented NOTE: The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 1

26、01 811-3-1 V1.3.1 (2004-08) 6 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AP Access Point CC Central Controller CL Convergence Layer CPCS Common Part Convergence Sublayer DLC Data Link Control DM Direct Mode DUC DLC User Connection ICS Implementatio

27、n Conformance Statement IUT Implementation Under Test MAC Medium Access Control PDU Protocol Data Unit PICS Protocol ICS RLC Radio Link Control SCS System Conformance Statement SSCS Service Specific Convergence Sublayer SUT System Under Test WCM Wireless Cycle Master WCS Wireless Cycle Slave WT Wire

28、less Terminal 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and order

29、ing of the proforma items. An PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 7 Annex A (normative): Protocol ICS proforma for TS 101 493-3 Notwiths

30、tanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1 Guidance fo

31、r completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 101 493-3 1 may provide information about the implementation in a standardized manner. The PICS proforma i

32、s subdivided into clauses for the following categories of information: - guidance for completing the PICS proforma; - identification of the implementation; - identification of TS 101 493-3 1; - global statement of conformance; - roles; - major capabilities; - PDUs; - PDU parameters. A.1.2 Abbreviati

33、ons and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 4. Item column The item column contains a number which identifies the item in the table. Item description column The item descriptio

34、n column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7 4, are used for the status column: m mandatory - the capability is required to be supporte

35、d. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use this capability in the given context. ETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 8 o.i qualified optio

36、nal - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) d

37、epends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested from

38、 the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ status above. Reference column The reference column makes reference to TS 101 493-3 1, except where explicitly stated otherwise. Support column The support column shall be filled in by the supp

39、lier of the implementation. The following common notations, defined in ISO/IEC 9646-7 4, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluat

40、ion of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference

41、 to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be u

42、sed. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N NOTE 2: As stated in ISO/IEC 9646-7 4, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means t

43、hat the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notations are used: - range of values: example: 5 20 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101

44、B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size ( ) example: size (1 8) ETSI ETSI TS 101 811-3-1 V1.3.1 (2004-08) 9 Values supported column The values supported column shall be filled in by the supplier of the implementation.

45、In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined

46、 as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 2: A.5/4 is the reference to the answer of item 4 in table 5 of a

47、nnex A. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause or table title indicates that the whole clause or the whole ta

48、ble is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. In particular, an explicit answer shall be entered, in each of the support or support

49、ed column boxes provided, using the notation described in clause A.1.2. If necessary, the supplier may provide additional comments in space at the bottom of the tables or separately. More detailed instructions are given at the beginning of the different clauses of the PICS proforma. A.2 Identification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbe