ETSI TS 101 823-1-1-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the Data Link Control (DLC) layer Part 1 Basic data transport functions Sub-_1.pdf

1、 ETSI TS 101 823-1-1 V1.4.1 (2004-08)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the Data Link Control (DLC) layer;Part 1: Basic data transport functions;Sub-part 1: Protocol Implementation ConformanceStatement (PICS) proformaETSI ETSI TS 10

2、1 823-1-1 V1.4.1 (2004-08) 2 Reference RTS/BRAN-002T0C4-1-1 Keywords access, control, data, HIPERLAN, PICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucr

3、atif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference

4、 in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that th

5、e document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal

6、.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTES

7、TSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Pa

8、rtners. ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 3 Contents Intellectual Property Rights5 Foreword.5 Introduction 6 1 Scope 7 2 References 7 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .8 4 Conformance to this PICS proforma specification.8 Annex A (normative): Protocol ICS

9、proforma for TS 101 761-1.9 A.1 Guidance for completing the PICS proforma.9 A.1.1 Purposes and structure9 A.1.2 Abbreviations and conventions 9 A.1.3 Instructions for completing the PICS proforma11 A.2 Identification of the implementation 11 A.2.1 Date of the statement11 A.2.2 Implementation Under T

10、est (IUT) identification .11 A.2.3 System Under Test (SUT) identification12 A.2.4 Product supplier12 A.2.5 Client (if different from product supplier)13 A.2.6 PICS contact person .13 A.3 Identification of TS 101 761-1 .14 A.4 Global statement of conformance.14 A.5 Roles.14 A.6 PICS for Mobile Termin

11、al MT or Access Point AP.14 A.6.1 MAC functions.14 A.6.1.1 Fixed capacity .14 A.6.1.2 Connection modes.15 A.6.2 Error Control capabilities .15 A.6.2.1 Acknowledged mode procedures 15 A.6.2.1.1 Acknowledged mode - transmitter capabilities .16 A.6.2.1.2 Acknowledged mode - receiver capabilities17 A.6.

12、2.1.3 Acknowledged mode - logical channel for data flow17 A.6.2.1.4 Acknowledged mode - logical channel for control flow .17 A.6.2.1.5 Acknowledged mode - messages 18 A.6.2.2 Repetition mode procedures .18 A.6.2.2.1 Repetition mode - transmitter capabilities.18 A.6.2.2.2 Repetition mode - receiver c

13、apabilities.18 A.6.2.2.3 Repetition mode - logical channel for data flow .19 A.6.2.2.4 Repetition mode - logical channel for control flow.19 A.6.2.2.5 Repetition mode - messages19 A.6.2.3 Unacknowledged mode procedures 19 A.6.2.3.1 Unacknowledged mode - transmitter capabilities .19 A.6.2.3.2 Unackno

14、wledged mode - receiver capabilities19 A.6.2.3.3 Unacknowledged mode - logical channel for data flow20 A.6.2.3.4 Unacknowledged mode - logical channel for control flow .20 A.6.2.3.5 Unacknowledged mode - messages.20 A.6.3 PDU descriptions20 A.6.4 PDU parameters .21 ETSI ETSI TS 101 823-1-1 V1.4.1 (2

15、004-08) 4 A.6.4.1 Parameters of UPLink_ARQ_feedback PDU .21 A.6.4.2 Parameters of Downlink_ARQ_feedback PDU21 A.6.4.3 Parameters of UPLink_Discard PDU .22 A.6.4.4 Parameters of Downlink_Discard PDU 22 A.6.4.5 Parameters of Resource Request Uplink.23 A.6.4.6 Parameters of Resource Request Uplink for

16、Direct Link23 History 24 ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non

17、-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/

18、home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the p

19、resent document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 1 of a multi-part deliverable covering BRAN HIPERLAN type 2 DLC layer, Basic data transport function, Testing Specifications, as identifi

20、ed below: Part 1: “Basic data transport functions“; Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS) specification“; Part 2: Radio Link Control (RLC) sublayer; Sub-part 1: “Pro

21、tocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS) specification“; Part 3: “Profile for business environment“; Sub-part 1: “Profile Requirement List (PRL) proforma“; Sub-part 2: “Test Suite Stru

22、cture and Test Purposes (TSS Sub-part 3: “Profile Test Specification (PTS) - Profile Specific Test Specification (PSTS)“. Part 4: “Extension for Home Environment“; Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Su

23、b-part 3: “Abstract Test Suite (ATS) specification“; Part 5: “Profile for Home Environment“; Sub-part 1: “Profile Requirement List proforma specification“; Sub-part 2: “Profile Test Specification (PTS) - Summary“; Sub-part 3: “Profile Test Specification (PTS) - Profile Specific Test Specification (P

24、STS)“. ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 6 Introduction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called a Protocol Implementat

25、ion Conformance Statement (PICS). ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 7 1 Scope The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for BRAN HIPERLAN type 2 DLC layer, Part 1: Basic Data Transport function, as defined in TS 101 761-1 1 in compliance

26、with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 2. It details in tabular form the implementation options, i.e. the optional functions additional to those which are mandatory to implement. 2 References The following documents cont

27、ain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-spec

28、ific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 761-1 (V1.3.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Data Link Control (DLC) La

29、yer; Part 1: Basic Data Transport Functions“. 2 ETSI ETS 300 406 (1995): “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing

30、 methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the p

31、resent document, the terms and definitions given in TS 101 761-1 1. ISO/IEC 9646-1 3. ISO/IEC 9646-7 4 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabil

32、ities have been implemented NOTE: The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an

33、implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 8 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AP Access Point ARQ Automatic Repeat Request CL Convergence Layer CRC Cyclic Redund

34、ancy Check DCCH Dedicated Control CHannel DLC Data Link Control EC Error Control ICS Implementation Conformance Statement IUT Implementation Under Test LCCH Link Control CHannel LCH Long CHannelMAC Medium Access Control MT Mobile Terminal PDU Protocol Data Unit PHY Physical layer PICS Protocol ICS R

35、LC Radio Link Control SCH Short CHannel SCS System Conformance Statement SUT System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the

36、PICS proforma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 101 823-1-1 V1.4.1

37、(2004-08) 9 Annex A (normative): Protocol ICS proforma for TS 101 761-1 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for i

38、ts intended purposes and may further publish the completed PICS. A.1 Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 101 761-1 1 may provide in

39、formation about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: - guidance for completing the PICS proforma; - identification of the implementation; - identification of TS 101 761-1 1; - global statement of confor

40、mance; - roles; - major capabilities; - PDUs; - PDU parameters. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 4. Item column The item column contains a number whi

41、ch identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7 4, are use

42、d for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use this capability in th

43、e given context. ETSI ETSI TS 101 823-1-1 V1.4.1 (2004-08) 10o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately following the table

44、. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table. i irrelevant (out-of-scope) - capability

45、 outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ status above. Reference column The reference column makes reference to TS 101 761-1 1, except where explicitly stat

46、ed otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 4, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no

47、 answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supp

48、orted for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single

49、 profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N NOTE 2: As stated in ISO/IEC 9646-7 4, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values all