ETSI TS 102 148-1-2-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Packet based Convergence Layer Part 1 Common part Sub-part 2 Test Suite Stru_1.pdf

1、 ETSI TS 102 148-1-2 V1.2.1 (2004-04)Technical Specification Broadband Radio Access Networks (BRAN);HIPERACCESS;Conformance testing for the Packet based Convergence Layer;Part 1: Common part;Sub-part 2: Test Suite Structure andTest Purposes (TSS Essential, or potentially Essential, IPRs notified to

2、ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be giv

3、en as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN).

4、The present document is part 1, sub-part 2 of a multi-part covering testing specification for the Packet based Convergence Layer of the BRAN HIPERACCESS system, as identified below: Part 1: “Common part“; Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test

5、Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS)“. Part 2: “Ethernet Service Specific Convergence Sublayer (SSCS)“. ETSI ETSI TS 102 148-1-2 V1.2.1 (2004-04) 5 1 Scope The present document contains the Test Suite Structure (TSS) and Test Purposes (TP) to test TS 102 117-

6、1 1. The objective of this test specification is to provide a basis for conformance tests for BRAN HIPERACCESS equipment giving a high probability of air interface inter-operability between different manufacturers BRAN HIPERACCESS equipment. The ISO standard for the methodology of conformance testin

7、g (ISO/IEC 9646-1 3 and ISO/IEC 9646-2 4) as well as the ETSI rules for conformance testing (ETS 300 406 2) are used as a basis for the test methodology. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. Refe

8、rences are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly avail

9、able in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 102 117-1: “Broadband Radio Access Networks (BRAN); HIPERACCESS; Packet based Convergence Layer; Part 1: Common Part“. 2 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile con

10、formance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance

11、testing methodology and framework - Part 2: Abstract test suite specification“. 5 ISO/IEC 9646-6: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test specification“. 6 ISO/IEC 9646-7: “Information technology - Open Sy

12、stems Interconnection - Conformance testing methodology and framework - Part 7: Implementation conformance statement“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 102 117-1 1 and ISO/IEC 9646-7 6 apply. ETSI ETSI TS

13、102 148-1-2 V1.2.1 (2004-04) 6 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ISO/IEC 9646-1 3, ISO/IEC 9646-6 5, ISO/IEC 9646-7 6, TS 102 117-1 1 and the following apply: AP Access Point ATM Asynchronous Transfer Mode BI Invalid Behaviour BO Inopportune Behav

14、iour BRAN Broadband Radio Access Networks (Project) BV Valid Behaviour CA CApability tests CL Convergence Layer CPCS Common Part Convergence Sublayer ETSI European Telecommunications Standards Institute IUT Implementation Under Test PBCL Packet Based Convergence Layer PDU Protocol Data Unit PICS Pro

15、tocol Implementation Conformance Statement SSCS Service Specific Convergence Sublayer TP Test Purposes TS Technical Specification TSS Test Suite Structure AT Access Terminal CPP Common Part Procedures SS Sender Side RS Receiver Side 4 Test suite structure 4.1 Structure Figure 1 shows the Common Pack

16、et Based Convergence Layer (PBCL) Test Suite Structure (TSS) including its subgroups defined for the conformance testing. Test Suite Protocol group Protocol subgroup Test group CA BV BI BO PCL-AP/ PCL-AT Common procedures Sender x Receiver x Figure 1: TSS for HIPERACCESS Common part PBCL The test su

17、ite is structured as a tree with a first level defined as PCL-AP or PCL-AT representing the protocol group “Common part PBCL for AP and Common part PBCL for AT“. 4.2 Test groups The test groups are organized in three levels. The first level creates one protocol group representing the protocol servic

18、es. The second level separates the protocol services in functional modules. The last level in each branch contains one or more of the standard ISO subgroups CA, BV, BI and BO. 4.2.1 Protocol groups The protocol groups identify the common part procedures as defined in TS 102 117-1 1. ETSI ETSI TS 102

19、 148-1-2 V1.2.1 (2004-04) 7 4.2.1.1 Common procedures The common part procedures group is divided in two functional modules. The first functional module identifies the procedures at the sender side. The last functional module identifies the procedures at the receiver side. 4.2.2 Main test groups The

20、 main test groups are the capability group, the valid behaviour group, the invalid behaviour group and the inopportune behaviour group. 4.2.2.1 Capability (CA) tests This test sub group shall provide limited testing of the major IUT capabilities aiming to insure that the claimed capabilities are cor

21、rectly supported, according to the PICS. 4.2.2.2 Valid Behaviour (BV) tests This test sub group shall verify that the IUT reacts in conformity with the TS, after receipt or exchange of valid Protocol Data Units (PDUs). Valid PDUs means that the exchange of messages and the content of the exchanged m

22、essages are considered as valid. 4.2.2.3 Invalid Behaviour (BI) tests This test sub group shall verify that the IUT reacts in conformity with the TS, after receipt of a syntactically invalid PDU. 4.2.2.4 Inopportune Behaviour (BO) tests This test sub group shall verify that the IUT reacts in conform

23、ity with the TS, after receipt of a syntactically correct PDU not expected in the actual message exchange. 5 Test Purposes (TP) 5.1 Introduction 5.1.1 TP definition conventions The TPs are defined following particular rules as shown in table 1. Table 1: TP definition rules TP Id according to the TP

24、naming conventions Reference. Initial condition. Stimulus. Expected behaviour. TP Id The TP Id is a unique identifier it shall be specified according to the TP naming conventions defined in the subclause below. Reference The reference should contain the references of the subject to be validated by t

25、he actual TP (specification reference, clause, and paragraph). Condition The condition defines in which initial state the IUT has to be to apply the actual TP. Stimulus The stimulus defines the test event to which the TP is related. Expected behaviour Definition of the events that are expected from

26、the IUT to conform to the base specification. ETSI ETSI TS 102 148-1-2 V1.2.1 (2004-04) 8 5.1.2 TP naming conventions The identifier of the TP is built according to table 2. Table 2: TP naming convention Identifier: TP/- = side type AP Access Point AT Access Terminal = protocol group CPP Common Part

27、 Procedures = functional module SS Sender Side RS Receiver Side x = Type of testing CA CApability tests BV Valid Behaviour tests BI Invalid Behaviour tests BO Inopportune Behaviour tests = sequential number (000-999) Test Purpose number EXAMPLE: TP/AT/CPP/RS/BV-010 is the tenth purpose for the valid

28、 behaviour testing of the procedures at the receiver of the common part procedures implemented at the AT side. 5.1.3 Sources of TP definitions All TPs are specified according to TS 102 117-1 1. 5.2 Test purposes for AP 5.2.1 Procedures at the sender TP/AP/CPP/SS/BV-000 Reference: TS 102 117-1 1 Init

29、ial condition: Connection established. IUT is the sender. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a continuous stream of CPCS PDU to send. TP/AP/CPP/SS/BV-001 Reference: TS 102 117-1 1 Initial condition: Connec

30、tion established. IUT is the sender. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a discontinuous flow of CPCS PDU to send. TP/AP/CPP/SS/BV-002 Reference: TS 102 117-1 1 Initial condition: Connection established. IU

31、T is the sender. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT segments correctly a large CPCS PDU. ETSI ETSI TS 102 148-1-2 V1.2.1 (2004-04) 9 5.2.2 Procedures at the receiver TP/AP/CPP/RS/BV-000 Reference: TS 102 117-1 1 Initial con

32、dition: Connection established. IUT is the receiver. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT delivers the payload of a correctly received CPCS PDU to SSCS higher layer. TP/AP/CPP/RS/BV-001 Reference: TS 102 117-1 1 Initial condi

33、tion: Connection established. IUT is the receiver. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a continuous stream of received CPCS PDU. TP/AP/CPP/RS/BV-002 Reference: TS 102 117-1 1 Initial condition: Connection e

34、stablished. IUT is the receiver. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a discontinuous flow of received CPCS PDU. TP/AP/CPP/RS/BV-003 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT i

35、s the receiver. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT reassembles correctly a large Data Unit 5.3 Test purposes for AT 5.3.1 Procedures at the sender TP/AT/CPP/SS/BV-000 Reference: TS 102 117-1 1 Initial condition: Connection

36、established. IUT is the sender. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a continuous stream of CPCS PDU to send. TP/AT/CPP/SS/BV-001 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is t

37、he sender. A loop back mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a discontinuous flow of CPCS PDU to send. TP/AT/CPP/SS/BV-002 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is the sender. A loop ba

38、ck mechanism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT segments correctly a large CPCS PDU. 5.3.2 Procedures at the receiver TP/AT/CPP/RS/BV-000 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is the receiver. A loop back mecha

39、nism is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT delivers the payload of a correctly received CPCS PDU to SSCS higher layer. TP/AT/CPP/RS/BV-001 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is the receiver. A loop back mechani

40、sm is implemented on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a continuous stream of received CPCS PDU. TP/AT/CPP/RS/BV-002 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is the receiver. A loop back mechanism is implemented

41、on top of either CPCS layer or SSCS layer at the IUT. Check, that: the IUT manages correctly a discontinuous flow of received CPCS PDU. TP/AT/CPP/RS/BV-003 Reference: TS 102 117-1 1 Initial condition: Connection established. IUT is the receiver. A loop back mechanism is implemented on top of either

42、CPCS layer or SSCS layer at the IUT. Check, that: the IUT reassembles correctly a large Data Unit ETSI ETSI TS 102 148-1-2 V1.2.1 (2004-04) 10Annex A (informative): Bibliography ITU-T Recommendation X.290: “OSI conformance testing methodology and framework for protocol Recommendations for ITU-T appl

43、ications - General concepts“. ITU-T Recommendation X.291: “OSI conformance testing methodology and framework for protocol Recommendations for ITU-T applications - Abstract test suite specification“. ETSI ETSI TS 102 148-1-2 V1.2.1 (2004-04) 11History Document history V1.1.1 November 2002 Publication V1.2.1 April 2004 Publication