ETSI TS 102 192-2-2004 Electromagnetic compatibility and Radio spectrum Matters (ERM) International Technical Characteristics and Test Methods Part 2 Cordless audio and Consumer ra.pdf

1、 ETSI TS 102 192-2 V1.1.1 (2004-08)Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM);International Technical Characteristics and Test Methods;Part 2: Cordless audio and Consumer radio microphones inthe 25 MHz to 3 GHz Frequency RangeETSI ETSI TS 102 192-2 V1.1.1

2、(2004-08) 2 Reference DTS/ERM-TG17-006-2 Keywords Audio, radio, radio mic, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Gra

3、sse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the

4、reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or

5、 change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by w

6、ritten permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo

7、 are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 3 Contents Intellectual Property Rights6 Foreword.6 1 Scope 7

8、2 References 7 3 Definitions, symbols and abbreviations .8 3.1 Definitions8 3.2 Symbols9 3.3 Abbreviations .9 4 Functional characteristics.10 4.1 Cordless audio 10 4.2 Consumer radio microphones.10 4.3 In-ear monitoring10 4.4 In-vehicle cordless10 4.5 Personal cordless 10 4.6 Broadband multi channel

9、 systems 10 5 General .10 5.1 Presentation of equipment for testing purposes10 5.1.1 Choice of model for performance testing .11 5.1.2 Definitions of alignment and switching ranges.11 5.1.3 Void 11 5.1.4 Choice of frequencies .11 5.1.5 Testing of single channel equipment 11 5.1.6 Testing of two chan

10、nel equipment12 5.1.7 Testing of multi-channel equipment (more than two channels)12 5.1.8 Testing of equipment with an external frequency control.12 5.1.9 Testing of equipment with an integral antenna.12 5.1.9.1 Equipment with a permanent internal RF port 12 5.1.9.2 Equipment with a temporary RF por

11、t12 5.2 Mechanical and electrical design13 5.2.1 General13 5.2.2 Controls 13 5.2.3 Testing with integral antenna13 5.2.4 Marking 13 5.2.4.1 Equipment identification.13 5.2.4.2 Regulatory marking.13 5.3 Interpretation of the measurement results 13 6 Test conditions, power sources and ambient conditio

12、ns 14 6.1 Normal and extreme test-conditions.14 6.2 Test power source.14 6.3 Normal test conditions14 6.3.1 Normal temperature and humidity14 6.3.2 Normal test power source voltage.14 6.3.2.1 Mains voltage14 6.3.2.2 Void.15 6.3.2.3 Other power sources15 6.4 Extreme test conditions 15 6.4.1 Extreme t

13、emperatures .15 6.4.1.1 Procedures for tests at extreme temperatures 15 6.4.2 Extreme test power source voltages15 6.4.2.1 Mains voltage15 6.4.2.2 Void.15 6.4.2.3 Void.15 6.4.2.4 Other power sources15 ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 4 7 General conditions16 7.1 Normal test modulation16 7.2 T

14、est fixture .17 7.3 Test site and general arrangements for radiated measurements17 7.4 Modes of operation of the transmitter 17 7.5 Arrangement for test signals at the input of the transmitter .18 8 Methods of measurement and limits for transmitter parameters 18 8.1 Frequency stability .18 8.1.1 Def

15、inition18 8.1.2 Method of measurement (analogue modulation) 18 8.1.3 Method of measurement (digital modulation).18 8.1.4 Limit .18 8.2 Rated output power 19 8.2.1 Definition19 8.2.2 Method of measurement for equipment with integral antenna19 8.2.2.1 Method of measurement under normal test conditions

16、 .19 8.2.3 Limit .19 8.3 Necessary bandwidth19 8.3.1 Definition19 8.3.2 Measurement of Necessary Bandwidth (BN) for analogue modulation .20 8.3.3 Measurement of Necessary Bandwidth (BN) for digital modulation20 8.3.4 Limits21 8.3.5 Edge of band limits.21 8.4 Spurious emissions.22 8.4.1 Definitions 2

17、2 8.4.2 Method of measurement .22 8.4.3 Limits23 8.4.4 Measuring receiver .23 8.5 Cordless audio transmitter shutoff23 8.5.1 Definition23 8.5.2 Method of measurement .24 8.5.3 Limits24 9 Receiver24 9.1 Spurious emissions.24 9.1.1 Definitions 24 9.1.2 Method of measuring the power level in a specifie

18、d load.24 9.1.3 Method of measuring the effective radiated power of the enclosure 25 9.1.4 Method of measuring the radiated power .25 9.1.5 Limits25 10 Measurement uncertainty .26 Annex A (normative): EMC requirements 27 Annex B (normative): Measurement of Necessary Bandwidth (BN) 28 Annex C (inform

19、ative): Receiver parameters29 C.1 Blocking or desensitization 29 C.1.1 Definition .29 C.1.2 Method of measurement.29 C.1.2.1 Measurement procedure29 C.1.2.2 Definitions 29 C.1.2.3 Limits for applications below 1 GHz30 C.1.2.4 Limits for applications above 1 GHz 30 C.2 Frequency mask for the receiver

20、 part.30 C.2.1 Definition .30 C.2.2 Method of measurement.30 C.2.3 Typical values for receivers31 C.2.3.1 Typical values for receivers with analogue modulation31 C.2.3.2 Typical values for receivers with digital modulation31 ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 5 Annex D (informative): Bibliograp

21、hy.32 History 33 ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members,

22、and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp).

23、 Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the presen

24、t document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 2 of a multi-part deliverable covering the International Technical Characteristics and Test Methods, as id

25、entified below: Part 1: “Wireless/Radio Microphones in the 25 MHz to 3 GHz Frequency Range“; Part 2: “Cordless audio and Consumer radio microphones in the 25 MHz to 3 GHz Frequency Range“. The present document was submitted to GSC9 (Seoul, 9 to 13 May 2004) where interested PSOs were requested to ta

26、ke the necessary action to transpose it into their own deliverables for application as appropriate. ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 7 1 Scope The present document covers the minimum characteristics considered necessary in order to make the best use of the available frequencies. It does not n

27、ecessarily include all the characteristics that may be required by a user, nor does it necessarily represent the optimum performance achievable. The present document applies to cordless audio and in ear monitoring equipment using either 300 kHz bandwidth analogue modulation or 300 kHz, 600 kHz or 1

28、200 kHz digital modulation. The frequency bands for this equipment may differ from country to country as specified in their national regulations. All equipment is intended to be used with integral antennas. The present document does not apply to broadband modulation such as spread spectrum technique

29、s. Consumer audio equipment intended for audio and voice operating below 50 MHz and using narrow band modulation are excluded from the present document. Electromagnetic Compatibility (EMC) requirements are covered by the present document in annex A. The types of equipment covered by the present docu

30、ment are examples as follows: - cordless headphones; - cordless loudspeakers; - consumer radio microphones; - in-ear monitoring; - in-vehicle cordless; - personal cordless; - broadband multi channel audio systems. 2 References The following documents contain provisions which, through reference in th

31、is text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. R

32、eferenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ITU-R Radio Regulations (Appendix 3 to WRC2000): “Table of maximum permitted spurious emission power levels “. 2 ITU-R Recommendation BS.559-2: “Objective me

33、asurement of radio-frequency protection ratios in LF, MF and HF broadcasting“. 3 ETSI TR 100 028 (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 4 EN 60244-13: “Methods of measurement for radio

34、 transmitters - Part 13: Performance characteristics for FM sound broadcasting“. ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 8 5 ANSI C63.5: “American National Standard for Calibration of Antennas Used for Radiated Emission Measurements in Electromagnetic Interference (EMI)“. 6 ETSI EN 301 489-1: “Elect

35、romagnetic compatibility and Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements“. 7 ETSI EN 301 489-9: “Electromagnetic compatibility and Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC) st

36、andard for radio equipment and services; Part 9: Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment, cordless audio and in-ear monitoring devices 8 Code of Federal Regulations: “Title 47: telecommunication; Chapter 1: Federal Communications Commission; Pa

37、rt 15: radio frequency devices“. 9 ETSI TR 100 027: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Methods of measurement for private mobile radio equipment“. 10 ITU-R Recommendation BS.412-9: “Planning standards for terrestrial FM sound broadcasting at VHF“. 11 CEPT/ERC/REC 74-01E

38、: “Spurious emissions“. 12 ETSI TS 102 192-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); International Technical Characteristics and Test Methods; Part 1: Wireless/Radio Microphones in the 25 MHz to 3 GHz Frequency Range“. 3 Definitions, symbols and abbreviations 3.1 Definition

39、s For the purposes of the present document, the following terms and definitions apply: alignment range: see clause 5.1.2 artificial antenna: tuned reduced-radiating dummy load equal to the nominal impedance specified by the applicant carrier power (of a radio transmitter): average power supplied to

40、the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation channel bandwidth: frequency band of defined width including safety margin for operation on adjacent channels, located symmetrically around the carrier frequency class of emissi

41、on: the set of characteristics of an emission, designated by standard symbols, e.g. type of modulation of the main carrier, modulating signal, type of information to be transmitted, and also, if appropriate, any additional signal characteristics dBc: decibels relative to the unmodulated carrier powe

42、r of the emission NOTE: In the cases which do not have a carrier, for example in some digital modulation schemes where the carrier is not accessible for measurement, the reference level equivalent to dBc is decibels relative to the mean power P. enclosure port: physical boundary of the apparatus thr

43、ough which electromagnetic fields may radiate or impinge NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port. integral antenna: antenna, with or without a connector, designed as, and declared as by the manufacturer, an indispensable part of the equipment m

44、ean power (of a radio transmitter): average power supplied to the antenna transmission line by a transmitter during an interval of time sufficiently long compared with the lowest frequency encountered in the modulation taken under normal operating conditions ETSI ETSI TS 102 192-2 V1.1.1 (2004-08) 9

45、 necessary bandwidth: for a given class of emission, the width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under specified conditions out-of-band emissions: emission on a frequency or frequencies immediately outsi

46、de the necessary bandwidth which results from the modulation process, but excluding spurious emissions peak envelope power (of a radio transmitter): average power supplied to the antenna transmission line by a transmitter during one radio frequency cycle at the crest of the modulation envelope taken

47、 under normal operating conditions port: any connection point on or within the Equipment Under Test (EUT) intended for the connection of cables to or from that equipment radiated measurements: measurements that involve the absolute measurement of a radiated electromagnetic field spurious emissions:

48、emission on a frequency or frequencies which are outside the necessary bandwidth and the level of which may be reduced without affecting the corresponding transmission of information. Spurious emissions include harmonic emissions, parasitic emissions, intermodulation products and frequency conversio

49、n products, but exclude out-of-band emissions switching range: see clause 5.1.2 unwanted emissions: consist of spurious emissions and out-of-band emissions 3.2 Symbols For the purposes of the present document, the following symbols apply: wavelength in metres F micro Farad W micro Watt ohm3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: ac alternating current B Channel Bandwidth BN Necessary Bandwidth CW continuous wave dBc dB relative to the carrier level dc direct current erp effective radiated