ETSI TS 102 486-2-1-2006 Electromagnetic compatibility and Radio spectrum Matters (ERM) Road Transport and Traffic Telematics (RTTT) Test specifications for Dedicated Short Range C.pdf

1、 ETSI TS 102 486-2-1 V1.1.1 (2006-03)Technical Specification Electromagnetic compatibility and Radio spectrum Matters (ERM);Road Transport and Traffic Telematics (RTTT);Test specifications for Dedicated Short Range Communication (DSRC) transmission equipment;Part 2: DSRC application layer;Sub-Part 1

2、: Protocol Implementation Conformance Statement (PICS) proforma specificationETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 2 Reference DTS/ERM-TG37-002-1 Keywords DSRC, application, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65

3、 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic

4、 version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ET

5、SI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, pl

6、ease send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunic

7、ations Standards Institute 2006. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI regist

8、ered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 3 Contents Intellectual Property Rights6 Foreword.6 1 Scope 7 2 References 7 3 Definitions and abbreviations.8 3.1 Definitions8 3.2 Abbreviations .8 4 Overview of the templates8 5 C

9、onformance requirement concerning PICS8 Annex A (normative): ICS proforma for DSRC application layer for OBU9 A.1 Guidance for completing the PICS proforma.9 A.1.1 Purposes and structure9 A.1.2 Abbreviations and conventions 9 A.1.3 Instructions for completing the PICS proforma11 A.2 Identification o

10、f the implementation 11 A.2.1 Date of the statement11 A.2.2 Implementation Under Test (IUT) identification .11 A.2.3 System Under Test (SUT) identification12 A.2.4 Product supplier12 A.2.5 Client (if different from product supplier)12 A.2.6 PICS contact person .13 A.3 Identification of the protocol1

11、3 A.4 Global statement of conformance.14 A.5 Kernels .14 A.6 Initialization Kernel14 A.6.1 Procedures 14 A.6.2 PDU14 A.7 Transport Kernel 15 A.7.1 Procedures 15 A.7.2 PDU16 A.8 Broadcast Kernel19 A.8.1 Procedures 19 A.8.2 PDU19 A.9 ASN.1 Data Types20 A.9.1 Extendable data types.20 A.9.2 Extendable l

12、ists 20 Annex B (normative): ICS proforma for DSRC application layer for RSU.21 B.1 Guidance for completing the PICS proforma.21 B.1.1 Purposes and structure21 B.1.2 Abbreviations and conventions 21 B.1.3 Instructions for completing the PICS proforma23 B.2 Identification of the implementation 23 B.2

13、.1 Date of the statement23 B.2.2 Implementation Under Test (IUT) identification .23 B.2.3 System Under Test (SUT) identification24 ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 4 B.2.4 Product supplier24 B.2.5 Client (if different from product supplier)24 B.2.6 PICS contact person .25 B.3 Identification

14、 of the protocol25 B.4 Global statement of conformance.26 B.5 Kernels .26 B.6 Initialization Kernel26 B.6.1 Procedures 26 B.6.2 PDU26 B.7 Transport Kernel 27 B.7.1 Procedures 27 B.7.2 PDU28 B.8 Broadcast Kernel31 B.8.1 Procedures 31 B.8.2 PDU31 B.9 ASN.1 Data Types32 B.9.1 Extendable data types.32 B

15、.9.2 Extendable lists 32 Annex C (normative): Profile Requirement List for RTTT profile of DSRC application layer for OBU.33 C.1 General .33 C.1.1 Profile Requirement List (profile RL)33 C.2 Identification of the profile.33 C.3 Kernels .34 C.4 Initialization Kernel34 C.5 Transport Kernel 34 C.5.1 PD

16、U34 C.6 ASN.1 Data Types35 C.6.1 Extendable data types.35 C.6.2 Extendable lists 35 Annex D (normative): Profile Requirement List for RTTT profile of DSRC application layer for RSU36 D.1 General .36 D.1.1 Profile Requirement List (profile RL)36 D.2 Identification of the profile.36 D.3 Kernels .37 D.

17、4 Initialization Kernel37 D.5 Transport Kernel 37 D.5.1 PDU37 D.6 ASN.1 Data Types38 D.6.1 Extendable data types.38 D.6.2 Extendable lists 38 Annex E (normative): Profile specific ICS proforma for RTTT profile of DSRC application layer for OBU.39 E.1 Guidance for completing the profile ICS proforma

18、.39 E.1.1 Purposes and structure39 ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 5 E.1.2 Abbreviations and conventions 39 E.1.3 Instructions for completing the profile ICS proforma 41 E.2 Identification of the implementation 41 E.2.1 Date of the statement41 E.2.2 Implementation Under Test (IUT) identifi

19、cation .41 E.2.3 System Under Test (SUT) identification42 E.2.4 Product supplier42 E.2.5 Client (if different from product supplier)42 E.2.6 Profile ICS contact person43 E.3 Identification of the profile.43 E.4 Global statement of conformance.44 E.5 Profiles .44 E.6 Interlayer Relations 44 E.6.1 Rec

20、eiver44 E.6.2 Transmitter .45 Annex F (normative): Profile specific ICS proforma for RTTT profile of DSRC application layer for RSU46 F.1 Guidance for completing the profile ICS proforma .46 F.1.1 Purposes and structure46 F.1.2 Abbreviations and conventions 46 F.1.3 Instructions for completing the p

21、rofile ICS proforma 48 F.2 Identification of the implementation 48 F.2.1 Date of the statement48 F.2.2 Implementation Under Test (IUT) identification .48 F.2.3 System Under Test (SUT) identification49 F.2.4 Product supplier49 F.2.5 Client (if different from product supplier)49 F.2.6 Profile ICS cont

22、act person50 F.3 Identification of the profile.50 F.4 Global statement of conformance.51 F.5 Profiles .51 F.6 Interlayer Relations 51 F.6.1 Transmitter .51 F.6.2 Receiver52 History 53 ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 6 Intellectual Property Rights IPRs essential or potentially essential to

23、the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ET

24、SI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given

25、 as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility

26、and Radio spectrum Matters (ERM). The present document is part 2, sub-part 1 of a multi-part deliverable covering the test specifications for CEN DSRC, as identified below: Part 1: “DSRC data link layer: medium access and logical link control“; Part 2: “DSRC application layer“: Sub-part 1: “Protocol

27、 Implementation Conformance Statement (PICS) proforma specification“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS) and partial PIXIT proforma“. ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 7 1 Scope The present document specifies partial Protocol Imple

28、mentation Conformance Statement (PICS) proformas for the application layer of CEN DSRC as defined in EN 12834 1, in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 5. This proforma is intended for use by suppliers of e

29、quipment which is claimed to conform to the CEN DSRC application layer, as specified in EN 12834 1. The present document also contains profile Implementation Conformance Statement (ICS) proformas and profile Requirements Lists for the application layer for use by suppliers of equipment which is clai

30、med to conform to EN 13372 2, DSRC Profiles for RTTT. To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance St

31、atement (ICS). The present document provides proforma ICS templates, to be filled in by equipment suppliers. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by dat

32、e of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found

33、at http:/docbox.etsi.org/Reference. 1 CEN EN 12834 (2003): “Road transport and traffic telematics - Dedicated Short Range Communication (DSRC). DSRC application layer“. 2 CEN EN 13372 (2004): “Road Transport and Traffic Telematics (RTTT) - Dedicated short-range communication - Profiles for RTTT appl

34、ications“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concept“. 4 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implement

35、ation Conformance Statements“. 5 ETSI ETS 300 406: “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 8 3 Definitions and abbreviations 3.1 Definitions For the purposes of the

36、present document, the terms and definitions given in EN 12834 1, EN 13372 2, ISO/IEC 9646-1 3, ISO/IEC 9646-7 4 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating whic

37、h capabilities have been implemented. The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS 3.2 Abbreviations For the pu

38、rposes of the present document, the abbreviations given in EN 12834 1, EN 13372 2, ISO/IEC 9646-1 3, ISO/IEC 9646-7 4 and the following apply: DSRC Dedicated Short Range Communication ICS Implementation Conformance StatementIUT Implementation Under Test ME Mobile Equipment OBU On Board Unit, an alte

39、rnative descriptor to Mobile Equipment PICS Protocol Implementation Conformance Statement RL Requirements List RSU Road Side Unit, an alternative descriptor to Fixed Equipment RTTT Road Transport and Traffic Telematics SUT System Under Test 4 Overview of the templates The present document contains s

40、eparate PICS templates for On Board Unit (OBU) and Road Side Unit (RSU). These can be found in annexes A and B respectively. In addition, the present document contains profile Requirement Lists (RL) and profile-specific ICS proformas for equipment claimed to conform to EN 13372 2. Again, these exist

41、 for the OBU and for the RSU. 5 Conformance requirement concerning PICS If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming a

42、nd ordering of the proforma items. An ICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the instructions for completion given at the start of each annex. ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 9 Annex A (normative): ICS proforma for DSRC a

43、pplication layer for OBU Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the ICS proforma in this annex so that it can be used for its intended purposes and may further publish the

44、 completed ICS. A.1 Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in EN 12834 1 may provide information about the implementation in a standardized

45、manner. The PICS proforma is subdivided into clauses for the following categories of information: guidance for completing the PICS proforma; identification of the implementation; identification of the protocol; global statement of conformance; PICS proforma tables: - Kernels; - Initialization Kernel

46、; - Transport Kernel; - Broadcast Kernel; - ASN.1 Data Types. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 4. Item column The item column contains a number which

47、 identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 102 486-2-1 V1.1.1 (2006-03) 10Status column The following notat

48、ions, defined in ISO/IEC 9646-7 4, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a re

49、quirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined