ETSI TS 102 527-2-2007 Digital Enhanced Cordless Telecommunications (DECT) New Generation DECT Part 2 Support of transparent IP packet data (V1 1 1)《数字增强无绳通信(DECT) 新一代DECT 第2部分 支持透.pdf

1、 ETSI TS 102 527-2 V1.1.1 (2007-06)Technical Specification Digital Enhanced Cordless Telecommunications (DECT);New Generation DECT;Part 2: Support of transparent IP packet dataETSI ETSI TS 102 527-2 V1.1.1 (2007-06) 2 Reference DTS/DECT-NG0245-2 Keywords access, data, DECT, DPRS, frame relay, IMT-20

2、00, internet, interoperability, interworking, IP, IPv6, LAN, mobility, multimedia, packet mode, profile, radio, synchronization, TDD, TDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Associat

3、ion but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perc

4、eived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should

5、be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following servic

6、es: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2007. All rights reserved.

7、 DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP O

8、rganizational Partners. ETSI ETSI TS 102 527-2 V1.1.1 (2007-06) 3 Contents Intellectual Property Rights6 Foreword.6 1 Scope 7 2 References 7 3 Definitions, symbols and abbreviations .9 3.1 Definitions9 3.2 Symbols9 3.3 Abbreviations .9 4 Description of Services 12 4.1 The data service in New Generat

9、ion DECT .12 4.1.1 Service objectives .12 4.1.2 Characteristics of the DECT packet data service12 4.2 Protocol architecture.13 4.2.1 IPv6.13 4.2.2 Other LAN protocols: DHCP, ARP, RARP .13 4.2.3 Data protocol reference configuration 13 4.2.3.1 IEEE 802.3/Ethernet over DECT (DPRS annex B.4) reference

10、configuration .14 4.2.3.2 Internet Protocol (IP) over DECT (DPRS annex B.6) reference configuration 15 4.2.3.3 Other implementation options.16 4.3 Performance Objectives .16 4.4 System Categories 17 4.5 General application environments18 4.5.1 Residential (home networking) environment18 4.5.2 Busine

11、ss scenario20 4.5.3 Small Office and Home Office (SOHO).22 4.6 Examples of implementation of most usual scenarios22 4.6.1 Fixed Part (FP) acting as a router with WLAN/DECT access point.22 4.6.2 Fixed Part (FP) acting as a switch with WLAN/DECT access point23 5 Relevant requirements23 5.1 Service and

12、 feature definitions .23 5.1.1 PHL service definitions 23 5.1.2 MAC service definitions.23 5.1.3 DLC service definitions 24 5.1.4 NWK feature definitions.24 5.1.5 Application service definitions .24 5.1.6 Management Entity (ME) definitions .24 5.1.7 Call Control (CC) and mobility management service

13、definitions.24 5.1.8 U-plane service and interworking definitions.24 5.1.9 NG-DECT Data System Categories (DSC) 24 5.2 Requirements applicable to categorized systems .24 5.2.1 Mapping between NG-DECT data categories and features/services 24 5.2.2 Supported data rates for equipment declaring complian

14、ce to a data category 26 5.2.3 Indication of compliance with a data category .27 6 Profile specific requirements27 6.1 General .27 6.2 General class/service/interworking support27 6.2.1 Class/service support 27 6.2.2 Protocol interworking support 28 6.3 Void28 6.4 Physical layer (PHL) requirements.2

15、8 6.4.1 Physical layer (PHL) services.28 6.4.2 Modulation schemes .29 6.4.3 PHL service to procedure mapping.29 ETSI ETSI TS 102 527-2 V1.1.1 (2007-06) 4 6.5 MAC layer requirements 29 6.5.1 MAC layer services 29 6.5.2 MAC service to procedure mapping .30 6.6 DLC layer.30 6.6.1 DLC layer services30 6

16、.6.2 DLC service to procedure mapping 30 6.7 NWK layer .31 6.7.1 General31 6.7.2 NWK features .31 6.7.3 NWK features to procedures mapping32 6.8 Application features .32 6.8.1 Application features32 6.8.2 Application features to procedures mapping.32 6.9 Distributed communications.32 6.10 Management

17、 Entity (ME).33 6.10.1 Management Entity (ME) operation modes33 6.10.2 Management Entity (ME) mode to procedures mapping33 7 Profile specific procedures description 33 7.1 General .33 7.2 Management Entity (ME) procedures 33 7.3 MAC layer procedures .33 7.4 DLC layer procedures 33 7.5 NWK layer proc

18、edures.33 7.5.1 Terminal capability indication 34 7.5.2 Call resources/parameters negotiation 35 7.5.3 IWU-attributes change35 7.5.4 Collective and group ringing 36 7.5.5 Broadcast attributes management .36 7.6 Interworking requirements .37 7.7 Physical layer procedures.37 Annex A (normative): Amend

19、ments to other DECT specifications 38 A.1 Amendments to EN 301 649 (DECT Packet Radio Service) .38 A.1.1 Scope (add to clause 1 of EN 301 649) 38 A.1.2 References (add to clause 1 of EN 301 649) 38 A.1.3 Definitions and abbreviations.40 A.1.3.1 Definitions (add to clause 3.1 of EN 301 649)40 A.1.3.2

20、 Definitions (modify clause 3.1 of EN 301 649)40 A.1.3.3 Abbreviations (add to clause 3.3 of EN 301 649).40 A.1.4 Description of services .41 A.1.4.1 Service Objectives (modify clause 4.2 of EN 301 649)41 A.1.4.2 Feature and service definitions (modify clause 4.3 of EN 301 649).44 A.1.4.3 General cl

21、ass/service/interworking support (modify clause 4.4 of EN 301 649)50 A.1.4.4 Requirements applicable to categorized systems (add to clause 4 of EN 301 649)51 A.1.5 PHL Requirements (modify clause 5 of EN 301 649)54 A.1.6 MAC layer Requirements (modify clause 6 of EN 301 649) .57 A.1.7 DLC layer Requ

22、irements (modify clause 7 of EN 301 649) 61 A.1.8 NWK layer Requirements (modify clause 8 of EN 301 649).63 A.1.9 Management Entity requirements (modify clause 9 of EN 301 649) .68 A.1.10 MAC layer Procedures .69 A.1.10.1 General (modify clause 10.1 of EN 301 649) .69 A.1.10.2 QT- FP capabilities (m

23、odify clause 10.3.2.2 of EN 301 649)71 A.1.10.3 PT initiated single duplex bearer setup (modify clause 10.10.1.1 of EN 301 649).72 A.1.10.4 FT initiated single duplex bearer setup (modify clause 10.10.1.2 of EN 301 649).73 A.1.10.5 PT initiated Single duplex bearer setup (remove from clause 10.10.2

24、of EN 301 649)73 A.1.10.6 Bearer quality report (modify clause 10.16.3 of EN 301 649)73 A.1.10.7 GFchannel (modify clause 10.20 of EN 301 649) .74 A.1.10.8 Time multiplexers (add to clause 10 of EN 301 649) .75 A.1.10.9 IPFchannel (add to clause 10 of EN 301 649) .77 A.1.11 DLC layer procedures 78 E

25、TSI ETSI TS 102 527-2 V1.1.1 (2007-06) 5 A.1.11.1 Insertion of FU10c frames in FU10a frames of the opposite link (add to clause 11.2.3 of EN 301 649).78 A.1.12 NWK layer procedures.78 A.1.12.1 Terminal capability indication (modify clause 12.3 of EN 301 649)78 A.1.12.2 Broadcast attributes managemen

26、t (modify clause 12.16 of EN 301 649).80 A.2 Amendments to EN 300 175-3 (DECT CI; MAC layer)82 A.2.1 Symbols and abbreviations.82 A.2.1.1 Symbols (add to clause 3.2 of EN 300 175-3) 82 A.2.1.2 Abbreviations (remove from clause 3.3 of EN 300 175-3).82 A.2.2 Higher layer U-Plane channels IPFand SIPF83

27、 A.2.2.1 The higher layer U-Plane channels (modify clause 5.3.1.2 of EN 300 175-3) 83 A.2.2.2 The higher layer U-Plane channel in E+U type slots, IPF(add to clause 5.3.1 of EN 300 175-3) .83 A.2.2.3 The connectionless U-Plane channel in E+U type slots, SIPF(add to clause 5.3.2 of EN 300 175-3).84 A.

28、2.3 Symmetric and Asymmetric connections .84 A.2.3.1 Symmetric connections (modify clause 5.6.2.1 of EN 300 175-3) .84 A.2.3.2 Asymmetric connections (modify clause 5.6.2.2 of EN 300 175-3).87 A.2.4 B-field control multiplexer.90 A.2.4.1 B-field control multiplexer (E/U-MUX) (modify clause 6.2.2.2 o

29、f EN 300 175-3) 90 A.2.4.2 B-field control multiplexer in E-type and E+U-type modes (modify clause 6.2.2.3 of EN 300 175-3) .91 A.2.4.2.1 B-field control multiplexer in E-type and E+U-type modes (modify clause 6.2.2.3 of EN 300 175-3)91 A.2.4.2.2 E-type and E+U-type modes for slots with more than on

30、e subfield (modify clause 6.2.2.3.1 of EN 300 175-3).91 A.2.4.2.3 Half slot (j=80) modes for 2-level modulation (remove from clause 6.2.2.3.2 of EN 300 175-3)96 A.2.4.2.4 Half slot (j=80) modes for 2-level modulation (add to clause 6.2.2.3.2 of EN 300 175-3)96 A.2.4.3 Priority scheme in E or E+U mod

31、e (add to clause 6.2.2 of EN 300 175-3).96 A.2.5 B-field identification, BA bits (modify clause 7.1.4 of EN 300 175-3) 98 A.2.6 Extended fixed part capabilities (part 2) (modify clause 7.2.3.11 of EN 300 175-3).98 A.2.7 Messages in the B-field 99 A.2.7.1 Messages in the B-field, Overview (modify cla

32、use 7.3.1 of EN 300 175-3) .99 A.2.7.2 Null or IPFsegmentation info (modify clause 7.3.3 of EN 300 175-3)101 A.2.7.3 Bearer quality in an asymmetric connection (add to clause 7.3.4.4 of EN 300 175-3).102 A.2.7.4 GFchannel data packet (modify clause 7.3.6 of EN 300 175-3) 102 A.2.8 Q2 and BCK bit set

33、ting for IP_error_correction services (modify clause 10.8.2.4.1 of EN 300 175-3)103 A.2.9 IPFProcedure description (add to clause 10.8 of EN 300 175-3) .103 A.3 Amendments to EN 300 175-5 (DECT CI; NWK layer) .107 A.3.1 References (add to clause 2 of EN 300 175-5).107 A.3.2 Terminal capability (add

34、to clause 7.7.41 of EN 300 175-5)107 A.3.3 Extended higher layer capabilities (part 2) (modify clause F.3 of EN 300 175-5).108 Annex B (informative): Bibliography.109 History 110 ETSI ETSI TS 102 527-2 V1.1.1 (2007-06) 6 Intellectual Property Rights IPRs essential or potentially essential to the pre

35、sent document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in r

36、espect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to

37、the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DEC

38、T). The present document is based on EN 300 175, parts 1 1 to 8 8 , EN 300 444 15 and EN 301 649 16. General attachment requirements and speech attachment requirements are based on EN 301 406 11 (replacing TBR 006 (see bibliography) and EN 300 176-2 10 (previously covered by TBR 010 (see bibliograph

39、y). The present document has been developed in accordance to the rules of documenting a profile specification as described in ISO/IEC 9646-6 12. The information in the present document is believed to be correct at the time of publication. However, DECT standardization is a rapidly changing area, and

40、 it is possible that some of the information contained in the present document may become outdated or incomplete within relatively short time-scales The present document is part 2 of a multi-part deliverable covering the New Generation DECT as identified below: Part 1: “Wideband speech“; Part 2: “Su

41、pport of transparent IP packet data“; Part 3: “Support of phase 2 services“. ETSI ETSI TS 102 527-2 V1.1.1 (2007-06) 7 1 Scope The present document specifies a set of functionalities of the New Generation DECT. The functionalities defined in this profile are based on DECT base standard, EN 300 175,

42、parts 1 1 to 8 8 , DECT Generic Access Profile (GAP), EN 300 444 15, and DECT Packet Radio Service (DPRS), EN 301 649 16. The New Generation DECT provides the following basic new functionalities: Wideband voice service. Packet-mode data service supporting Internet Protocol with efficient spectrum us

43、age and high data rates. The present document describes the second part: packet-mode data service supporting Internet Protocol with efficient spectrum usage and high data rate. For description of the Wideband voice service see TS 102 527-1 17. All New Generation DECT devices will offer at least one

44、or both of these services. If the device offers the wideband voice service, it will support also the DECT standard 32 kbit/s voice service according to EN 300 444 15 (GAP). All DECT devices claiming to be compliant with this Application Profile will offer at least the basic services defined as manda

45、tory. In addition to that, optional features can be implemented to offer additional DECT services. The aim of the present document is to guarantee a sufficient level of interoperability and to provide an easy route for development of DECT data applications, with the features of the present document

46、being a common fall-back option available in all compliant to this profile equipment. DECT does not standardize Internet Application protocols or other high layer data protocols, which are in the scope of other standarization organizations. 2 References The following documents contain provisions whi

47、ch, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, th

48、e latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term valid

49、ity. 1 ETSI EN 300 175-1: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 1: Overview“. 2 ETSI EN 300 175-2: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical layer (PHL)“. 3 ETSI EN 300 175-3: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 3: Medium Access Control (MAC) layer“. 4 ETSI EN 300 175-4: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 4: Data Link Control (DLC) layer“. 5 ETS