ETSI TS 102 587-3-2010 Electromagnetic compatibility and Radio spectrum Matters (ERM) Peer-to-Peer Digital Private Mobile Radio Part 3 Requirements catalogue (V1 3 1)《电磁兼容性和无线频谱事务(.pdf

1、 ETSI TS 102 587-3 V1.3.1 (2010-09)Technical Specification Electromagnetic compatibility andRadio spectrum Matters (ERM);Peer-to-Peer Digital Private Mobile Radio;Part 3: Requirements catalogueETSI ETSI TS 102 587-3 V1.3.1 (2010-09)2Reference RTS/ERM-TGDMR-297-3 Keywords digital, mobile, private, ra

2、dio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document c

3、an be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, th

4、e reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI doc

5、uments is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written pe

6、rmission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2010. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Mem

7、bers. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and o

8、wned by the GSM Association. ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)3Contents Intellectual Property Rights 4g3Foreword . 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 5g33.1 Definitions 5g33.2 Abbreviations . 6g34 Requirem

9、ents catalogue . 7g34.1 dPMR common requirements . 7g34.1.1 All Call . 7g34.1.2 Channel Access . 8g34.1.3 Framing . 14g34.1.3.1 End Frame . 17g34.1.3.2 Header Frames 22g34.1.3.2.1 Call Information Field . 31g34.1.3.3 Packet Data Frame 35g34.1.3.4 Superframe 38g34.1.3.4.1 Type 1 Data . 42g34.1.3.4.2

10、Type 2 Data . 47g34.1.3.4.3 Voice . 50g34.1.4 Late Entry . 54g34.1.5 Powersave. 55g34.1.6 Talking Party Identification 58g34.2 Configured Services and Facilities Radios . 58g34.2.1 Broadcast Call . 58g34.2.2 Dialling Plan . 59g34.2.3 Individual Short Data 78g34.2.3.1 ISDM Free Text Message . 78g34.2

11、.3.2 ISDM Precoded Message 78g34.2.3.3 ISDM Short File Transfer . 79g34.2.3.4 ISDM Status Message . 79g34.2.4 Off Air Call Set-up . 80g34.2.5 Short Appended Data 80g34.2.6 Slow User Data . 82g34.2.7 Type 3 Data. 83g34.3 Initial Services and Facilities Radios . 85g3History 86g3ETSI ETSI TS 102 587-3

12、V1.3.1 (2010-09)4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Inte

13、llectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no inves

14、tigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specif

15、ication (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 3 of a multi-part deliverable covering the Electromagnetic compatibility and Radio spectrum Matters (ERM); Peer-to-Peer Digital Private Mobile Radio

16、, as identified below: Part 1: “Conformance testing; Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Conformance testing; Test Suite Structure and Test Purposes (TSS Part 3: “Requirements catalogue“; Part 4: “Conformance testing; Abstract Test Suite (ATS)“; Part 5: “Interope

17、rability testing; Interoperability Test Suite Structure and Test Purposes (TSS Part 6: “Interoperability testing; Test Descriptions (TD)“. ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)51 Scope The present document is to provide a catalogue of requirements extracted from ETSI Specifications. The catalogues

18、 has been written based on the test specification framework defined in TS 102 351 2. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific refe

19、rences, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the

20、time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI TS 102 490 (V1.6.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Peer-to-Peer Digital

21、 Private Mobile Radio using FDMA with a channel spacing of 6,25 kHz with e.r.p. of up to 500 mW“. 2 ETSI TS 102 351 (V2.1.1): “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT); IPv6 Testing: Methodology and Framework“. 2.2 Informative references The following referenced d

22、ocuments are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI ETS 300 230: “Radio Equipment and Systems (RES); Land mobile service; Binary Interchange of Information and Signalling (BIIS) at 1 200 bit/s (BIIS 1 200)

23、“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: conditionally mandatory: requirement that shall be supported by a standard conformant equipment if and only if the condition(s) stated within its requirement text a

24、re met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. EXAMPLE: Such a condition may be the support of an optional higher level requirement by the equipment. conditionally optional: requirement that may be supported by a standard conformant equipment i

25、f and only if the condition(s) stated within its requirement text are met NOTE: If one of these conditions is not met the requirement is considered to be not applicable. mandatory: requirement that shall be supported by a standard conformant equipment ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)6not appl

26、icable: requirement that does not have to be met by a standard conformant equipment optional: requirement that may be supported by a standard conformant equipment 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ACK ACKnowledgment AI Air Interface ARQ Au

27、tomatic Retransmission reQuest CC Colour Code CCH Control CHannel CI Call InformationCont Continuation flag CRC Cyclic Redundancy Checksum for data error detection CSF Configured Services and Facilities Di-bit 2 bits grouped together to represent a 4-level symbol DP Data Position ET End Type FDMA Fr

28、equency Division Multiple Access FEC Forward Error Correction FN Frame Numbering HI Header Information HT Header Type ID IDentifierISF Initial Services and Facilities MFID Manufacturers FID MS Mobile StationNACK Negative ACKnowledgment OACSU Off Air Call Set Up PAR PARameter dataPDF Packet Data Form

29、at RF Radio Frequency RSSI Received Signal Strength Indication SLD SLow Data SYNC SYNChronization TCH Traffic CHannel ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)74 Requirements catalogue 4.1 dPMR common requirements 4.1.1 All Call RQ_001_0824 All Call TS 102 490 1 Clause: 8.1.1.1 3 Type: Mandatory Appli

30、es to: ISF Requirement: A dPMR radio shall support voice group “All call“ supplementary service. Specification Text: All radios will decode an All call (common ID = 255) irrespective of the common ID selected by the user. However, radios that have 255 selected as the common ID will only respond to c

31、alls addressed to a common ID of 255. Family: No Duplicates Test Purposes: TP_PMR_0824_01 (Interoperability), TP_PMR_0824_02 (Interoperability), TP_PMR_0824_03 (Interoperability), TP_PMR_0824_01 (Conformance), TP_PMR_0824_02 (Conformance), TP_PMR_0824_03 (Conformance) RQ_001_0858 All Call TS 102 490

32、 1 Clause: 8.1.1.1 3 Type: Conditionally Mandatory Applies to: ISF Requirement: IF an ISF radio Common ID is set to 255 THEN the radio shall only respond to call addressed to Common ID of 255. Specification Text: All radios will decode an All call (common ID = 255) irrespective of the common ID sele

33、cted by the user. However, radios that have 255 selected as the common ID will only respond to calls addressed to a common ID of 255. Family: No Duplicates Test Purposes: TP_PMR_0858_02 (Interoperability), TP_PMR_0858_01 (Interoperability), TP_PMR_0858_01 (Conformance), TP_PMR_0858_02 (Conformance)

34、ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)8RQ_001_1317 All Call TS 102 490 1 Clause: A.2.3.3 1 Type: Conditionally Mandatory Applies to: CSF Requirement: For a CSF radio complying with the Standard User Interface the All Call dialled strings shall be dialled and encoded as follows: The All Call dialled

35、 string “n*“ (All Call within a prefix) User dialled string Air Interface ID Remark “0*“ 18 CC 3E All Talkgroup ID0 “1*“ 2F 23 62 All Talkgroup ID1 etc. etc. etc. “9*“ E1 DC 82 All Talkgroup ID9 The All Call dialled string: “*“ is mapped to the All Talkgroup ID15 and addresses all MSs irrespective o

36、f their prefix. User dialled string Air Interface ID Remark “*“ F8 33 A6 All Talkgroup ID15 Specification Text: The All Call dialled string “n*“ (All Call within a prefix) is mapped as shown in table A.3. Table A.2.3.3.1: Mapping of prefixed All Call to the AI User dialled string Air Interface ID Re

37、mark “0*“ 18 CC 3E All Talkgroup ID0 “1*“ 2F 23 62 All Talkgroup ID1 etc. etc. etc. “9*“ E1 DC 82 All Talkgroup ID9 The All Call dialled string: “*“ is mapped to the All Talkgroup ID15 and addresses all MSs irrespective of their prefix. Table A.2.3.3.2: Mapping of all prefix call to the AI User dial

38、led string Air Interface ID Remark “*“ F8 33 A6 All Talkgroup ID15 Family: RQ_001_1317, RQ_001_1410, RQ_001_1411 Test Purposes: TP_PMR_1317_01 (Conformance), TP_PMR_1317_02 (Conformance), TP_PMR_1317_03 (Conformance), TP_PMR_1317_04 (Conformance) 4.1.2 Channel Access RQ_001_1001 Channel Access TS 10

39、2 490 1 Clause: 10.1 2 Type: Mandatory Applies to: ISF, CSF Requirement: A caller radio shall listen before transmit. When the received signal level has not exceeded -105 dBm for the duration of the T_ch_chk timer then the radio shall assume the channel to be free. Specification Text: When determini

40、ng whether activity is present on a channel, the radio shall monitor the RSSI level. If after a maximum period of time (T_ch_chk) the RSSI level has not exceeded a configurable (within a predefined range) threshold RSSI_LO, then the radio shall assume that activity is not present on the channel. RSS

41、I_LO shall be set to -105 dBm 3 dB. Family: No Duplicates Test Purposes: None ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)9RQ_001_1002 Channel Access TS 102 490 1 Clause: 10.1 5 Type: Conditionally Mandatory Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. IF the received signa

42、l level is equal or above -105 dBm AND the radio can synchronize on the channel. THEN the radio shall assume that there is dPMR activity on the channel. Specification Text: If however the RSSI level does exceed this threshold, then the radio shall assume that activity is present on the channel and i

43、t shall attempt to become frame synchronized to the activity. If the radio is successful in becoming frame synchronized to the activity, then the radio shall assume that 6,25 kHz FDMA activity is present on the channel. Family: No Duplicates Test Purposes: None RQ_001_1003 Channel Access TS 102 490

44、1 Clause: 10.1 5 Type: Conditionally Mandatory Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. IF the received signal level is above -105 dBm AND the radio can not synchronize to the channel for the duration of the T_ch_free timer THEN it shall assume the activity is not

45、dPMR. Specification Text: If however the RSSI level does exceed this threshold, then the radio shall assume that activity is present on the channel and it shall attempt to become frame synchronized to the activity. If however after a maximum period of time (T_ch_free), the radio has not become frame

46、 synchronized to the activity, then the radio shall assume that the activity is non-6,25 kHz FDMA activity. Family: No Duplicates Test Purposes: None RQ_001_1004 Channel Access TS 102 490 1 Clause: 10.1 5 Type: Mandatory Applies to: ISF, CSF Requirement: A radio shall listen before transmitting. Whe

47、n the received signal level is above -105 dBm and the radio manages to synchronize to the channel but the color code is incorrect then it shall assume the activity is interference. Specification Text: If the radio is successful in becoming frame synchronized to the activity, then the radio shall ass

48、ume that 6,25 kHz FDMA activity is present on the channel. If the Colour Code is different then the radio shall assume that the activity is interference. Family: No Duplicates Test Purposes: TP_PMR_1004_01 (Conformance) ETSI ETSI TS 102 587-3 V1.3.1 (2010-09)10RQ_001_1005 Channel Access TS 102 490 1

49、 Clause: 10.2.2 1 Type: Mandatory Applies to: ISF, CSF Requirement: IF a transmitting radio announces a non zero Tx WAIT time then other radios shall not commence any PTT activated transmissions during this Tx WAIT period. Specification Text: When a transmitting radio announces a non zero Tx WAIT time then PTT activated transmissions shall not be permitted to