ETSI TS 102 760-3-2014 Intelligent Transport Systems (ITS) Communications Access for Land Mobiles (CALM) Test specifications for Access Technology Support (ISO 21218) Part 3 Abstra.pdf

1、 ETSI TS 102 760-3 V1.1.1 (2014-06) Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for Access Technology Support (ISO 21218); Part 3: Abstract Test Suite (ATS) and partial PIXIT proforma floppy3Technical Specification ETSI ETSI TS 102 760-3 V1

2、.1.1 (2014-06)2Reference DTS/ITS-0020021 Keywords ATS, CALM, ITS, testing, TTCN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse

3、 (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior writ

4、ten authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present documen

5、t should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the followi

6、ng services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version sha

7、ll not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered fo

8、r the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)3Contents Intellectual Prop

9、erty Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Abstract test method . 6g34.1 Abstract protocol tester 6g34.2 Test architect

10、ure . 8g34.3 Ports and abstract service primitives 9g34.3.1 Overview 9g34.3.2 ASPs of the atspPort . 9g34.3.3 ASPs of the utPort 10g34.3.4 ASPs of the cfPort 10g35 ATS conventions 10g3Annex A (normative): Partial PIXIT proforma for ATSP . 12g3A.1 Identification summary. 12g3A.2 ATS summary 12g3A.3 T

11、est laboratory 12g3A.4 Client identification 13g3A.5 SUT 13g3A.6 Protocol layer information 13g3A.6.1 Protocol identification 13g3A.6.2 IUT information . 14g3Annex B (normative): TTCN-3 library modules . 16g3B.1 Electronic annex, zip file with TTCN-3 code 16g3History 17g3ETSI ETSI TS 102 760-3 V1.1.

12、1 (2014-06)4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellect

13、ual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including I

14、PR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been

15、 produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The present document is part 3 of a multi-part deliverable covering the test specifications for ITS access technology support (service access points and related procedures) ISO 21218 1 as identified below: Part 1: “ Implement

16、ation Conformance Statement (ICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial PIXIT proforma“. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “may not“, “need“, “need not“, “will“

17、, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)51 Scop

18、e The present document provides the Abstract Test Suite (ATS) and partial PIXIT proforma for the protocols specified in ISO 21218 1 based on the related TSS Communications Access for Land Mobiles (CALM); Test specifications for access technology support (ISO 21218); Part 1: Protocol implementation c

19、onformance statement (PICS) proforma“. 3 ETSI TS 102 760-2 (V1.2.1): “Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for access technology support (ISO 21218); Part 2: Test Suite Structure and Test Purposes (TSS Protocol and profile conformanc

20、e testing specifications; Standardization methodology“. 7 ETSI ES 201 873-1: “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. 8 ETSI ES 201 873-7: “Methods for Testing and Specification (MTS); The Testing and Test Control N

21、otation version 3; Part 7: Using ASN.1 with TTCN-3“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EG 202 798: “Intelligent Transport Systems (ITS

22、); Testing; Framework for conformance and interoperability testing“. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)6i.2 ISO 21217:2014: “Intelligent transport systems - Communications access for land mobiles (CALM) - Architecture“. i.3 ISO 24102-3:2013: “Intelligent transport systems - Communications acces

23、s for land mobiles (CALM) - ITS station management - Part 3: Service access points“. i.4 ISO 24102-4:2013: “Intelligent transport systems - Communications access for land mobiles (CALM) - ITS station management - Part 4: Station internal management communications“. i.5 ISO 21215:2010: “Intelligent t

24、ransport systems - Communications access for land mobiles (CALM) - M5“. i.6 ETSI TR 103 099 (V1.1.1): “Intelligent Transport Systems (ITS);Architecture of conformance validation framework“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and defini

25、tions given in ISO 21218 1, ETSI TS 102 760-1 2, ETSI TS 102 760-2 3, ISO 24102-4 i.4, ISO/IEC 9646-1 4, ISO/IEC 9646-2 5, ETSI ETS 300 406 6, ETSI ES 201 873-1 7, ETSI ES 201 873-7 8, ETSI EG 202 798 i.1, ISO 21217 i.2, ISO 24102-3 i.3 and ISO 21215 i.5 apply. 3.2 Abbreviations For the purposes of

26、the present document, the abbreviations given in ISO 21218 1, ETSI TS 102 760-1 2, ETSI TS 102 760-2 3, ISO 24102-4 i.4, ISO/IEC 9646-1 4, ISO/IEC 9646-2 5, ETSI ETS 300 406 6, ETSI ES 201 873-1 7, ETSI ES 201 873-7 8, ETSI EG 202 798 i.1, ISO 21217 i.2, ISO 24102-3 i.3 and ISO 21215 i.5 apply. 4 Ab

27、stract test method 4.1 Abstract protocol tester In general, the conformance test system architecture as illustrated in the ITS testing framework ETSI EG 202 798 i.1 applies. This ITS testing framework is extended by a cnPort and the related configuration / event notification transport as illustrated

28、 in figure 1. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)7SUTITS test systemConfiguration / notification transportTest controlTTCN-3 test componentsITS lower layersCodecUpper tester applicationITS lower layersUpper tester transportIUTltPortutPortLower layers linkUpper tester transport linkConfiguration

29、/ notification transportUpper tester transportcnPortConfiguration / notification linkTest adapterFigure 1: Abstract protocol tester - General approach For the present document, the IUT is the ATSP. The upper tester application allows accessing the IN-SAP of the IUT. Lower layer protocols indicated b

30、y the block “ITS lower layers“ are not existent, as the ATSP constitutes the lowest layer (ITS-S access layer) of the ITS-S station and communication architecture ISO 21217 i.2. The configuration and event notification access allows to access the IUT via the MI-SAP. NOTE 1: The ITS-S access layer co

31、rresponds to the OSI layers 1 and 2. ISO 21218 1 specifies how to use any kind of access technology in an ITS station (ITS-S). Thus ISO 21218 does not contain details of this variety of possible access technologies. Testing of ISO 21218 thus needs to apply the ATSPs to a specific access technology.

32、An “Implementation Under Test“ IUT contained in a “System Under Test“ (SUT) is connected to the ITS test system via a lower layers link and an upper tester transport link and a configuration / notification link. These links allow accessing the points of control and observation (PCO) of the IUT. Thes

33、e three links between ITS test system and SUT may be realized differently, such that there might be one or two or three physical links. NOTE 2: The lower layers link is the link of a specific access technology, e.g. 802.11(p) radio link as specified in ISO 21215 i.5. Accessing the IUT is performed w

34、ith the “ITS station-internal management communications protocol“ (IICP) specified in ISO 24102-4 i.4 as illustrated in figure 2. Further on an auxiliary ITS station unit (AITS-SU) with a communication interface (CI) of same access technology as used in the IUT is needed for the lower layers link. F

35、or this purpose, the ITS test system, the AITS-SU and the SUT together behave as parts of an ITS station unit, where each of these three units constitutes an ITS station communication unit (ITS-SCU) as specified in ISO 21217 i.2 and ISO 24102-4 i.4. The unique address of the ITS test system ITS-SCU

36、is ITS-SCU-ID = 3 as specified in ISO 24102-4 i.4. The unique address of the CI ITS-SCU is ITS-SCU-ID = 4 as specified in ISO 24102-4 i.4. The unique address ITS-SCU-ID of the SUT is in the range of 8 through 66 534 and may be selected by different means, e.g. using the initialization procedure of I

37、ICP specified in ISO 24102-4 i.4. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)8Figure 2: Abstract protocol tester - IUT located in the ITS-S access layer - IICP approach for upper tester and configuration / notification access The test system simulates valid and invalid protocol behaviour, and analyses t

38、he reaction of the IUT upon a given stimulation. 4.2 Test architecture The present document implements the general TTCN-3 test architecture described in ETSI EG 202 798 i.1, clause 6.3.2 and clause 8.3.1. Figure 3 shows the TTCN-3 test architecture used for the ATSP ATS. The MTC is of type ItsATSP a

39、nd communicates with the SUT over atspPort (PCO Link) in order to exchange access technology specific PDUs between the ATSP test component and the ATSP IUT. The “ITS lower layers transport“ system adapter connects to the AITS-SU containing the same access technology as used in the SUT. This connecti

40、on uses PDUs which are equivalent to the IN-SAP service primitives specified in ISO 21218 1. The MTC communicates with the SUT over the utPort (PCO IN-SAP) in order to trigger ATSP functionalities by simulating service primitives from the IN-SAP services. It is required to trigger the ATSP in the SU

41、T to send frames. Furthermore, receiving frames may result for the ATSP in sending primitives to the upper layer, which is the ITS-S networking 5.2 Naming conventions 5.2.1 General guidelines The present document follows the naming convention guidelines provided in ETSI EG 202 798 i.1. ETSI ETSI TS

42、102 760-3 V1.1.1 (2014-06)115.2.2 Usage of Log statements All TTCN-3 log statements use the following format: Three asterisks followed by a blank character. The TTCN-3 test case or function identifier in which the log statement is defined followed by a colon and a blank character. One of the possibl

43、e log categories: INFO, WARNING, ERROR, PASS, FAIL, INCONC, TIMEOUT followed by a colon and a blank character. Free text. A blank character followed by three asterisks. EXAMPLE: log(“* TC_ATSP_SE_BV_01: INFO: Waiting for power-on of IUT *“); Furthermore, the following rules are applied for the Atsp

44、ATS: Log statements are used in the body of the functions, so that invocation of functions is visible in the test logs. All TTCN-3 setverdict statements are combined with a log statement following the same above rules. 5.2.3 Test Case (TC) identifier Table 1 shows the test case naming convention, wh

45、ich follows the test purposes ETSI TS 102 760-2 3 naming convention. Table 1: TC naming convention TC_ = root ATSP Access Technology Support Protocols = group SE State event transitions MB MIB I-Parameters HC Handling of CIs DP Handling of data plane = type of testing BV Valid Behaviour tests BI Inv

46、alid Syntax or Behaviour Tests = sequential number 01 to 99 EXAMPLE: TP identifier: TP/ATSP/SE/BV/01 TC identifier: TC_ATSP_SE_BV_01. ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)12Annex A (normative): Partial PIXIT proforma for ATSP Notwithstanding the provisions of the copyright clause related to the te

47、xt of the present document, ETSI grants that users of the present document may freely reproduce the Partial PIXIT proforma for ATSP in this annex so that it can be used for its intended purposes and may further publish the completed Partial PIXIT. A.1 Identification summary Table A.1 PIXIT Number: T

48、est Laboratory Name: Date of Issue: Issued to: A.2 ATS summary Table A.2: Summary Protocol Specification: ISO 21218 1 with access technology according to: Protocol to be tested: ATSP ATS Specification: ETSI TS 102 760-3 Abstract Test Method: Clause 4 A.3 Test laboratory Table A.3: Test laboratory Te

49、st Laboratory Identification: Test Laboratory Manager: Means of Testing: SAP Address: ETSI ETSI TS 102 760-3 V1.1.1 (2014-06)13A.4 Client identification Table A.4: Client identification Client Identification: Client Test manager: Test Facilities required: A.5 SUT Table A.5: SUT identification Name: Version:SCS Number: Machine configuration: Operating System Identification: IUT Identification: PICS Reference for IUT: Limitations of the SUT: