ETSI TS 102 985-2-2014 Intelligent Transport Systems (ITS) Communications Access for Land Mobiles (CALM) Test specifications for non-IP networking (ISO 29281) Part 2 Test Suite Str.pdf

1、 ETSI TS 102 985-2 V1.2.1 (2014-06) Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for non-IP networking (ISO 29281); Part 2: Test Suite Structure and Test Purposes (TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of

2、ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPR

3、s not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The present document is pa

4、rt 2 of a multi-part deliverable covering Communications Access for Land Mobiles (CALM); Test specifications for non-IP networking (ISO 29281), as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “

5、Abstract Test Suite (ATS) and partial PIXIT proforma“. ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)51 Scope The present document provides the test suite structure and test purpose specification for the ISO protocols specified in ISO 29281-1 1 in compliance with the relevant requirements, and in accordanc

6、e with the relevant guidance given in EG 202 798 i.1. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of t

7、he reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI canno

8、t guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ISO 29281-1:2013: “Intelligent transport systems - Communication access for land mobiles (CALM) - Non-IP networking - Part 1: Fast networking

9、 Communications Access for Land Mobiles (CALM); Test specifications for non-IP networking (ISO 29281); Part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document b

10、ut they assist the user with regard to a particular subject area. i.1 ETSI EG 202 798: “Intelligent Transport Systems (ITS); Testing; Framework for conformance and interoperability testing“. i.2 Void. i.3 ISO 24102-3: “Intelligent transport systems - Communications access for land mobiles (CALM) - I

11、TS station management - Part 3: Service access points“. i.4 ISO 24102-4: “Intelligent transport systems - Communications access for land mobiles (CALM) - ITS station management - Part 4: Station-internal management communications“. i.5 ISO 21217: “Intelligent transport systems - Communications acces

12、s for land mobiles (CALM) - Architecture“. i.6 Void. ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)63 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO 29281-1 1, TS 102 985-1 2 and EG 202 798 i.1 apply. 3.2 Abbreviations For the

13、purposes of the present document, the abbreviations given in ISO 29281-1 1, TS 102 985-1 2, EG 202 798 i.1 and the following apply: FNTP Fast Networking this allows avoiding the ITS lower layers. 5 TP basics 5.1 TP definition conventions The TP definition is built according to the guidelines provide

14、d in the ITS testing framework i.1, applying a formalized language with pre-defined keywords for the behaviour description. 5.2 TP identifier naming conventions The identifier of the TP is built according to Table 1 as recommended in the ITS testing framework i.1. ETSI ETSI TS 102 985-2 V1.2.1 (2014

15、-06)8Table 1: TP naming convention for FNTP 1 TP/ = root FNTP Fast Networking & Transport Layer Protocol = group TXP Transmit Packets RXP Receive Packets CIP CIP Management SEC Secure Communications = sub-group BP Basic Procedure EP Extended Procedure FP Forwarding Procedure = type of testing BV Val

16、id Behaviour Tests BI Invalid Syntax or Behaviour Tests = sequential number 01 to 99 NOTE 1: CIP management is only tested in the TPs of group “CIP“. NOTE 2: The groups TXP and RXP are restricted to “transmit to / receive from an ITS peer station“, i.e. the group TXP also includes TPs to test recept

17、ion of an FNTP station-internal forwarding NPDU from another local ITS-SCU, and the group RXP also includes TPs to test transmission of an FNTP station-internal forwarding NPDU to another local ITS-SCU. NOTE 3: A sub-group may not apply for all groups. TPs for FNTP are specified in clause 6. 5.3 Rul

18、es for behaviour description The description of the TP is built according to the guidelines provided in the ITS testing framework i.1. 5.4 Sources of TP definitions All TPs are specified according to 1. 5.5 TP proforma i.1 proposes a TP proforma which is used in the present document. The fields of t

19、his proforma as used in the present document are explained in table 2. Table 2: TP proforma field description TP Header TP ID The TP ID is a unique identifier according to the TP naming conventions in Table 1. Test objective Short description of test purpose objective according to the requirements f

20、rom the base standard. Reference The reference indicates the clauses of the reference standard specifications in which the conformance requirement is expressed. PICS selection Reference to the PICS statement involved for selection of the TP. Contains a Boolean expression. May contain PICS acronyms s

21、pecified in Table 3. This section is only used in case an optional or conditional behaviour needs to be selected. Mandatory behaviour is not identified here. TP Behaviour Initial conditions (optional) The initial conditions define in which initial state the IUT has to be to apply the actual TP. In t

22、he corresponding “Test Case“ (TC), when the execution of the initial condition does not succeed, it leads to the assignment of an Inconclusive verdict. Expected behaviour (TP body) Definition of the events, which are parts of the TP objective, and the IUT are expected to perform in order to conform

23、to the base specification. In the corresponding TC,“ Pass“ or “Fail“ verdicts can be assigned there. ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)95.6 PICS mnemonics The PICS mnemonics presented in Table 3 are used in the TP proforma. Table 3: PICS mnemonic for ISO 29281-1 1 Mnemonic PICS item PICS_ROLE_R

24、ONLY 2 A.2/1 PICS_ROLE_HONLY 2 A.2/2PICS_ROLE_RH 2 A.2/3PICS_EXT 2 A.3/2PICS_ITS_S_INW 2 A.4/1 PICS_SEC 2 A.4/2PICS_NHOPBC 2 A.4/3PICS_LPP 2 A.4/4PICS_CIP 2 A.4/5 PICS_15628 2 A.5/16 TPs for FNTP 6.1 Transmit packets 6.1.1 Basic Procedure 6.1.1.1 Valid behaviour tests TP Id FNTP/TXP/BP/BV/01 Test ob

25、jective Single hop broadcast transmission request with known VCI Reference ISO 29281-1 1, clause 7.6.1 and clause 7.6.2 PICS Selection PICS_ROLE_RH Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the local port number of the ITS-S application Expected

26、behaviour ensure that when the IUT having received a correctly formatted single hop BC transmission request then the IUT generates a basic FNTP NPDU, and forwards it to the BC-VCI(s) for transmission ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)10TP Id FNTP/TXP/BP/BV/02 Test objective Single hop unicast t

27、ransmission request with known VCI Reference ISO 29281-1 1, clause 7.6.1 and clause 7.6.2 PICS Selection PICS_ROLE_RH Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the requested local port number of the ITS-S application Expected behaviour ensure tha

28、t when the IUT having received a correctly formatted single hop UC transmission request then the IUT generates a basic FNTP NPDU, and forwards it to the proper UC-VCI for transmission 6.1.1.2 Invalid behaviour tests Invalid test purposes will be defined once ISO has implemented the concept of path a

29、nd flow management in the architecture standard ISO 21217 i.5 and subsequently in ISO 29281-1 1. 6.1.2 Extended Procedure 6.1.2.1 Valid behaviour tests TP Id FNTP/TXP/EP/BV/01 Test objective N- hop broadcast transmission request with known VCI Reference ISO 29281-1 1, clause 7.6.3 PICS Selection PIC

30、S_EXT AND PICS_ROLE_RH AND PICS_NHOPBC Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the requested local port number of the ITS-S application Expected behaviour ensure that when the IUT having received a correctly formatted N-hop BC transmission requ

31、est then the IUT generates an extended FNTP NPDU, and forwards it to the BC-VCI(s) for transmission ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)116.1.2.2 Invalid behaviour tests TP Id FNTP/TXP/EP/BI/01 Test objective N- hop broadcast transmission request with invalid FNTP control field, and with known VC

32、I Reference ISO 29281-1 1, clause 7.6.3 PICS Selection PICS_EXT AND PICS_ROLE_RH AND PICS_NHOPBC Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the requested local port number of the ITS-S application Expected behaviour ensure that when the IUT having

33、 received an N-hop BC transmission request with non-supported bits in “controlField“ also set to 1 then the IUT reports failure of delivery 6.1.3 Forwarding Procedure 6.1.3.1 Valid behaviour tests TP Id FNTP/TXP/FP/BV/01 Test objective TX from ITS-S host Reference ISO 29281-1 1, clause 7.6.4 PICS Se

34、lection PICS_ITS_S_INW AND (PICS_ROLE_HONLY OR PICS_ROLE_RH) Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the requested local port numbers of the ITS-S application Expected behaviour ensure that when the IUT having received a correctly formatted sin

35、gle hop BC transmission request for delivery via a VCI contained in a different ITS-SCU then the IUT generates an FNTP forwarding NPDU, and forwards it to the BC-VCI for transmission to the selected ITS-S router ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)12TP Id FNTP/TXP/FP/BV/02 Test objective RX at IT

36、S-S router Reference ISO 29281-1 1, clause 7.6.4 and clause 7.7.7 PICS Selection PICS_ITS_S_INW AND (PICS_ROLE_RONLY OR PICS_ROLE_RH) Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of an ITS-S application in an ITS-S host Expected behaviour ensure that w

37、hen the IUT having received an FNTP station-internal forwarding NPDU containing a correctly formatted FNTP basic NPDU for single hop BC transmission then the IUT extracts the FNTP basic NPDU, and forwards it to the BC-VCI for transmission via the IN-SAP TP Id FNTP/TXP/FP/BV/03 Test objective TX from

38、 ITS-S host - increment of Counter Reference ISO 29281-1 1, clause 7.6.4 PICS Selection PICS_ITS_S_INW AND (PICS_ROLE_HONLY OR PICS_ROLE_RH) Initial conditions with the IUT having an FNTP forwarding table with proper entry in support of the requested local port numbers of the ITS-S application Expec

39、ted behaviour ensure that when the IUT having received a sequence of correctly formatted single hop BC transmission requests for delivery via a VCI contained in a different ITS-SCU, with the number of requests such that at least once the “Counter“ value before increment is different to 255, and at l

40、east once it is equal to 255 then the IUT generates an FNTP forwarding NPDU for every request, with the “Counter“ value in an FNTP forwarding NPDU equal to the “Counter“ value from the previous FNTP forwarding NPDU incremented by one with a wrap around from the value 255 to 0 6.1.3.2 Invalid behavio

41、ur tests TP Id FNTP/TXP/FP/BI/01 Test objective TX from ITS-S host - unknown access to ITS station-internal network Reference ISO 29281-1 1, clause 7.6.4 PICS Selection PICS_ITS_S_INW AND (PICS_ROLE_HONLY OR PICS_ROLE_RH) Initial conditions with the IUT having an FNTP forwarding table with no entry

42、related to an ITS-S internal network Expected behaviour ensure that when the IUT having received a correctly formatted single hop BC transmission request for delivery via a VCI contained in a different ITS-SCU then the IUT reports failure of delivery ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)136.2 Rece

43、iving packets 6.2.1 Basic Procedure 6.2.1.1 Valid behaviour tests TP Id FNTP/RXP/BP/BV/01 Test objective Single hop unicast reception from peer station Reference ISO 29281-1 1, clause 7.7.1, clause 7.7.2 and clause 7.7.3 PICS Selection PICS_ROLE_RH Initial conditions with the IUT having a proper ent

44、ry in the FNTP forwarding table with Service Port such that no ITS station-internal forwarding is needed Expected behaviour ensure that when the IUT having received a correctly formatted unicast packet from the peer station via the IN-SAP then the IUT delivers the message to the local ITS-SP selecte

45、d by the Service Port TP Id FNTP/RXP/BP/BV/02 Test objective Single hop unicast reception from unknown peer station Reference ISO 29281-1 1, clause 7.7.1, clause 7.7.2 and clause 7.7.3 PICS Selection PICS_ROLE_RH Initial conditions with the IUT having an entry in the FNTP forwarding table for a Serv

46、ice Port such that no ITS station-internal forwarding is needed, but no entry for the peer station Expected behaviour ensure that when the IUT having received a correctly formatted unicast packet from the peer station via the IN-SAP then the IUT delivers the message to the ITS-SP selected by the Ser

47、vice Port, the ITU informs the management about the new peer ITS-S ETSI ETSI TS 102 985-2 V1.2.1 (2014-06)14TP Id FNTP/RXP/BP/BV/03 Test objective Single hop broadcast reception from peer station Reference ISO 29281-1 1, clause 7.7.1, clause 7.7.2 and clause 7.7.3 PICS Selection PICS_ROLE_RH Initial

48、 conditions with the IUT having an entry in the FNTP forwarding table for a Service Port such that no ITS station-internal forwarding is needed Expected behaviour ensure that when the IUT having received a correctly formatted broadcast packet from the peer station via the IN-SAP then the IUT forward

49、s the message to the ITS-SP selected by the Service Port 6.2.1.2 Invalid behaviour tests TP Id FNTP/RXP/BP/BI/01 Test objective Single hop broadcast reception to unknown Service Port Reference ISO 29281-1 1, clause 7.7.1 and clause 7.7.2 PICS Selection PICS_ROLE_RH OR PICS_ROLE_RONLY OR PICS_ROLE_HONLY Initial con