ETSI TS 103 021-3-2003 Access and Terminals (AT) Harmonized basic attachment requirements for Terminals for connection to analogue interfaces of the Telephone Networks Update of th.pdf

1、 ETSI TS 103 021-3 V1.1.2 (2003-09)Technical Specification Access and Terminals (AT);Harmonized basic attachment requirements for Terminals forconnection to analogue interfaces of the Telephone Networks;Update of the technical contents of TBR 021, EN 301 437,TBR 15, TBR 17;Part 3: Basic Interworking

2、 with the Public Telephone NetworkETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 2 Reference RTS/AT-010118 Keywords access, PSTN, terminal, POTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Associati

3、on but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perce

4、ived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should b

5、e aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notificat

6、ion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for

7、the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 3 Conte

8、nts Intellectual Property Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .8 4 Requirements9 4.1 Parallel connection .9 4.2 Feeding voltage 9 4.3 Requirements in all conditions: polarity.9 4.4 General requirements in quiescent state .9

9、 4.4.1 DC resistance 9 4.4.2 Characteristics of TE for ringing signals 9 4.4.2.1 Impedance .9 4.4.2.2 Transient response.10 4.4.2.3 DC current.10 4.4.3 Resistance to earth 10 4.4.4 Impedance.10 4.5 Ringing signal detection sensitivity11 4.6 Transition from quiescent to loop state 11 4.6.1 Acceptance

10、 of breaks in the loop in a call attempt11 4.6.2 Loop current characteristics12 4.6.3 On-Hook to Off-Hook transition with ringing without DC 13 4.6.4 Ring trip14 4.7 Loop steady state characteristics 15 4.7.1 DC characteristics.15 4.7.2 Impedance.16 4.7.3 Resistance to earth 16 4.8 Call attempt 16 4

11、.8.1 Automatic dialling 16 4.8.1.1 Dialling without dial tone detection 16 4.8.1.2 Dialling with dial tone detection .16 4.8.2 DTMF signalling 17 4.8.2.1 Frequency combination.17 4.8.2.2 Signalling levels17 4.8.2.2.1 Absolute levels 17 4.8.2.2.2 Level difference.18 4.8.2.3 Unwanted frequency compone

12、nts .18 4.8.2.4 Tone duration 18 4.8.2.5 Pause duration.18 4.8.3 Loop disconnect dialling.18 4.8.4 Register recall .18 4.8.5 Call attempt on a low voltage line 18 4.9 Transition from loop state to quiescent state 19 Annex A (informative): Test methods20 A.1 General .20 A.2 Test impedances .20 A.3 Fe

13、eding bridge20 A.4 Test methods 20 A.4.1 Parallel connection .20 ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 4 A.4.2 Feeding voltage 20 A.4.3 Requirements in all conditions .20 A.4.4 General requirements in quiescent state .20 A.4.4.1 DC Resistance.20 A.4.4.2 Characteristics of TE for ringing signals 21

14、 A.4.4.2.1 Impedance .21 A.4.4.2.2 Transient response.22 A.4.4.2.3 DC current.23 A.4.4.3 Resistance to earth 24 A.4.4.4 Impedance.25 A.4.5 Ringing signal detector sensitivity .26 A.4.6 Transition from quiescent state to loop state 27 A.4.6.1 Acceptance of breaks in the loop in a call attempt27 A.4.6

15、.2 Loop current characteristics28 A.4.6.3 On-hook to off-hook transition with ringing without DC .29 A.4.6.4 Ring trip29 A.4.7 Loop steady state characteristics 30 A.4.7.1 DC characteristics.30 A.4.7.2 Impedance.31 A.4.7.3 Resistance to earth 32 A.4.8 Call attempt 33 A.4.8.1 Automatic dialling 33 A.

16、4.8.1.1 Dialling without dial tone detection 33 A.4.8.1.2 Dialling with dial tone detection .34 A.4.8.2 DTMF signalling 35 A.4.8.2.1 Frequency combinations .35 A.4.8.2.2 Signalling levels36 A.4.8.2.3 Unwanted frequency components .37 A.4.8.2.4 Tone duration 39 A.4.8.2.5 Pause duration.40 A.4.8.3 Loo

17、p disconnect dialling.42 A.4.8.4 Register recall .42 A.4.8.5 Call attempt on a low voltage line 42 A.4.9 Transition from loop to quiescent state 43 Annex B (informative): Requirements Table (RT)44 B.1 Guidance for completion of the RT44 B.1.1 Condition table .44 B.1.2 Requirements table.44 Annex C (

18、informative): Bibliography.47 History 48 ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI m

19、embers and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp

20、.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,

21、 essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Access and Terminals (AT). The present document is a minor editorial update of the first version to include text which was omitted from tables B.1 and B.2. The present documen

22、t is part 3 of a multipart deliverable covering technical updates to the TBRs: Part 1: “General aspects“; Part 2: “Basic transmission and protection of the network from harm“. Part 3: “Basic Interworking with the Public Telephone Network“, standardizes the aspects of interworking with the network. T

23、his part 3 only applies to TE intended for switched networks“. ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 6 1 Scope The present document is a part of a multipart document. It specifies basic compatibility and interoperability aspects, including basic transmission, which are applicable to all Terminal E

24、quipment (TE) intended to be connected to analogue interfaces of public or private, switched or non switched telephone networks. The present document is applicable to a TE which is capable of accessing an analogue telephone network line at the Network Termination Point (NTP). The present document is

25、 intended to ensure correct interworking between network and terminal so that calls can be routed successfully through the network, but without any guarantee of terminal to terminal interoperability. The present document is intended to ensure that no harm occurs to the network. 2 References The foll

26、owing documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not a

27、pply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 Void. 2 ETSI ES 201 235 (all parts): “Specification of Dual Tone Multi-Frequency (DTMF) tran

28、smitters and receivers“. 3 ETSI ES 201 970 (2002): “Access and Terminals (AT); Public Switched Telephone Network (PSTN); Harmonized specification of physical and electrical characteristics at a 2-wire analogue presented Network Termination Point (NTP)“. 4 ETSI ES 201 187: “2-wire analogue voice band

29、 interfaces; Loop Disconnect (LD) dialling specific requirements“. 5 ETSI ES 201 729: “Public Switched Telephone Network (PSTN); 2-wire analogue voice band switched interfaces; Timed break recall (register recall); Specific requirements for terminals“. 6 ETSI EG 201 120: “Public Switched Telephone N

30、etwork (PSTN); Method of rating terminal equipment so that it can be connected in series and/or in parallel to a Network Termination Point (NTP)“. 7 Void. 8 ITU-T Recommendation G.100: “Definitions used in Recommendations on general characteristics of international telephone connections and circuits

31、“. 9 ETSI TR 101 183: “Public Switched Telephone Network (PSTN); Analogue ringing signals“. 10 ETSI TR 101 041 (all parts): “Human Factors (HF); European harmonization of network generated tones“. 11 ITU-T Recommendation E.180: “Technical characteristics of tones for the telephone service“. 12 ITU-T

32、 Recommendation Q.35: “Technical characteristics of tones for the telephone service“. ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 7 13 ETSI TS 103 021-1: “Access and Terminals (AT); Harmonized basic attachment requirements for Terminals for connection to analogue interfaces of the Telephone Networks; Up

33、date of the technical contents of TBR 021, EN 301 437, TBR 015, TBR 017; Part 1: General Aspects“. 14 ETSI TBR 038: “ Public Switched Telephone Network (PSTN); Attachment requirements for a terminal equipment incorporating an analogue handset function capable of supporting the justified case service

34、 when connected to the analogue interface of the PSTN in Europe“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: automatic repeat call attempt: attempt made by the TE to the same network address as the result of th

35、e failure of the previous call attempt and not as a result of an external stimulus to the TE call attempt: process by which the TE seizes the PSTN line and sends signalling characters of the network address with which the TE wishes to communicate connection to earth: all the following points, as app

36、licable are connected to the earth point during measurement: a point in the TE which is intended to be connected to mains earth (in practice this might be carried out by connecting to the earth of the mains source which is supplying the TE); connector points which are intended to be connected to ear

37、th during the normal operation of the apparatus. dBV: absolute voltage level expressed in decibels with respect to 1 volt loop state: state where the TE draws sufficient DC current to activate the exchange loop steady state: loop state excluding the transitions from and to quiescent state Network Te

38、rmination Point (NTP): physical point at the boundary of the PSTN intended to accept the connection of a TE NOTE: See figure 1. quiescent state: state where the TE draws insufficient DC current to activate the exchange peak to peak voltage: the difference between the maximum and minimum voltage duri

39、ng any 10 ms window Public Switched Telephone Network (PSTN): term is used to describe the ordinary telephone system including subscriber lines, local exchanges and the complete system of trunks and the exchange hierarchy which makes up the network reference impedance ZR: complex impedance made up o

40、f 270 in series with a parallel combination of 750 and 150 nF NOTE: This is shown in figure A.1 of TS 103 021-1 13. repeat call attempt: further call attempt to the same network address resulting from a failure to establish connection during the previous call attempt repeat call attempt sequence: se

41、ries of internally generated automatic repeat call attempts made in response to an initial call attempt NOTE: Additional, but separate, call requests are permitted to initiate separate repeat call attempt sequences. return loss: As defined in ITU-T Recommendation G.100 8 clause 1.22 ETSI ETSI TS 103

42、 021-3 V1.1.2 (2003-09) 8 Telephone Network (TN): telecommunication network mainly exchanging voice band signals NOTE: TN is a general term for PSTN, non-switched leased lines and Private telephone networks. Terminal Connection Point (TCP): point of the TE intended to be connected to the Telephone N

43、etwork. NOTE: An adapter may be required between the terminal and the existing national network termination point in individual countries. Such an adapter is outside the scope of the present document (see figure 1). Suitable adapter installation TE TCP NTP TCP interface NTP interface TN Figure 1: Te

44、rminal connection point and network termination point Terminal Equipment (TE): equipment intended to be connected to the TN; i.e.: to be connected directly to the termination (NTP) of a TN; or to interwork with a TN being connected directly or indirectly to the NTP, in order to send, process or rece

45、ive information. The system of connection may be wire, radio, optical or other electromagnetical system NOTE: TE intended to be connected to public networks may be subject to particular regulatory treatment, whereas TE intended to be connected to private networks are usually not subject to particula

46、r regulatory treatment. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AC Alternating Current DC Direct Current DTMF Dual Tone Multi-Frequency EMF Electro Motive Force LU Loading Units NTP Network Termination Point PSTN Public Switched Telephone Networ

47、k rms root mean square SLIC Subscriber Line Integrated Circuit TCP Terminal Connection Point TE Terminal EquipmentTN Telephone Network ETSI ETSI TS 103 021-3 V1.1.2 (2003-09) 9 4 Requirements 4.1 Parallel connection As stated in TS 103 021-1 13, although up to four TE are considered for parallel con

48、nection, it is assumed that only one of them is in the loop state at any one time. It is assumed that the network driving capability is 100 LU as defined in EG 201 120 6. 4.2 Feeding voltage The feeding voltage value of 50 VDC in the requirement and test parts is only a harmonized test value. It doe

49、s not necessarily reflect the real TN supply voltages. 4.3 Requirements in all conditions: polarity Justification: Interworking with the TN is assured by requiring the TE to operate with both DC polarities, since a fixed polarity is not guaranteed. Requirement: The TE shall conform to the requirements of this document for both polarities of the DC line feeding voltage. Test: Where tests with both polarities are needed, this is indicated in relevant clauses in annex A. 4.4 General requirements in quiescent state 4.4.1 DC resi