ETSI TS 103 530-2-2018 Core Network and Interoperability Testing (INT) NAS Conformance Testing for the S1-MME interface (3GPP Release 13) Part 2 Test Suite Structure (TSS) and Test.pdf

1、 ETSI TS 103 530-2 V1.1.1 (2018-02) Core Network and Interoperability Testing (INT); NAS Conformance Testing for the S1-MME interface; (3GPPTMRelease 13); Part 2: Test Suite Structure (TSS) and Test Purposes (TP) TECHNICAL SPECIFICATION ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)2 Reference DTS/INT-0013

2、6-2 Keywords conformance, TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, includi

3、ng IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include tra

4、demarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present docu

5、ment does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability Testing (INT). The present document is part 2 of a multi

6、-part deliverable. Full details of the entire series can be found in part 1 2. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting

7、 Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)5 1 Scope The present document provides the Test Suite Structure (TSS) and Test Purposes (TP) for the test sp

8、ecification for the NAS protocol on the S1-MME interface as specified in ETSI TS 124 301 1 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ETSI ETS 300 406 5. 2 References 2.1 Normative references References are either specific

9、(identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not foun

10、d to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the

11、application of the present document. 1 ETSI TS 124 301 (V13.9.0): “Universal Mobile Telecommunications System (UMTS); LTE; Non-Access-Stratum (NAS) protocol for Evolved Packet System (EPS); Stage 3 (3GPP TS 24.301 version 13.9.0 Release 13)“. 2 ETSI TS 103 530-1: “Core Network and Interoperability T

12、esting (INT); NAS Conformance Testing for the S1-MME interface; (3GPP Release 13); Part 1: Protocol Implementation Conformance Statement (PICS). 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO

13、/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 5 ETSI ETS 300 406: “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardiza

14、tion methodology“. 6 ETSI TS 136 413 (V13.4.0): “LTE; Evolved Universal Terrestrial Radio Access Network (E-UTRAN); S1 Application Protocol (S1AP) (3GPP TS 36.413 version 13.4.0 Release 13)“. 2.2 Informative references References are either specific (identified by date of publication and/or edition

15、number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication,

16、 ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)6 3 Definitions and abbreviation

17、s 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI TS 124 301 1 and the following apply: Abstract Test Method (ATM): Refer to ISO/IEC 9646-1 3. Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 3. Implementation Under Test (IUT): Refer to ISO/IEC 964

18、6-1 3. Test Purpose (TP): Refer to ISO/IEC 9646-1 3. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ETSI TS 124 301 1 and the following apply: MI Message Information NAS Non-Access Stratum S1AP S1 Application Protocol TP Test Purpose TSS Test Suite Structure 4

19、 Test configurations 4.1 Introduction Test purposes of the present document address the VoLTE functional entity MME that is accessible via the standardized S1-MME interface. 4.2 Test configuration using the S1-MME interface The S1-MME interface is located between the eNB and the MME. The NAS message

20、s are transparent for the eNB, therefore only the MME is considered a System Under test (SUT). Figure 1: Test configuration CF_S1-MME TS SUT S1-MME MME eNB ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)7 5 Test Suite Structure (TSS) and Test Purposes (TP) 5.1 Test Suite Structure 5.1.1 TP naming convention

21、 TPs are numbered, starting at 01, within each group. Groups are organized according to the TSS. Table 1: TP identifier naming convention scheme Identifier: _ = Test Purpose: fixed to “TP“ Interface or protocol: NAS = type of IUT: MME = group MGR EMM / GUTI relocation procedure MAU EMM / Authenticat

22、ion procedure MSM EMM / Security mode control procedure MID EMM / Identification procedure MEI EMM / EMM information procedure MAT EMM / Attach procedure MDE EMM / Detach procedure MTA EMM / Tracking area updating procedure (S1 mode only) MSR EMM / Service request procedure MPA EMM / Paging procedur

23、e MTR EMM / Transport of NAS messages procedure MGT EMM / Generic transport of NAS messages procedure MES EMM / EMM Status SDF ESM / Default EPS bearer context activation procedure SDE ESM / Dedicated EPS bearer context activation procedure SCM ESM / EPS bearer context modification procedure SCD ESM

24、 / EPS bearer context deactivation procedure SPC ESM / UE requested PDN connectivity procedure SPD ESM / UE requested PDN disconnect procedure SRA ESM / UE requested bearer resource allocation procedure SRM ESM / UE requested bearer resource modification procedure SEI ESM / ESM information request p

25、rocedure SNO ESM / Notification procedure SRR ESM / Remote UE Report procedure STU ESM / Transport of user data via the control plane procedure = sequential number (01 to 99) ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)8 5.1.2 Test strategy As the base specification in ETSI TS 124 301 1 contains no expli

26、cit requirements for testing, the TPs were generated as a result of an analysis of the base standard and the PICS specification ETSI TS 103 530-1 2. 5.1.3 TP structure Each TP has been written in a manner which is consistent with all other TPs. The intention of this is to make the TPs more readable

27、and checkable. A particular structure has been used which is illustrated in table 2. Table 2 should be read in conjunction with any TP, i.e. please use a TP as an example to facilitate the full comprehension of table 2. Table 2: Structure of a single TP TP part Text Example Header see table 1 clause

28、 8.2.1 A.4/3 Summary Short free text description of the test objective Verify that the IUT can successfully process all mandatory IEs in an ATTACH REQUEST received due to attach procedure Configuration Test configuration as described in clause 4.2 CF_S1-MME Initial condition (optional) Free text des

29、cription of the condition that the IUT has reached before the test purpose applies Start point Ensure that the IUT in the see ETSI TS 124 301 1 clause 8.1 Network initiated detach procedure and/or further actions before stimulus if the action is sending/receiving see below for message structure Havi

30、ng sent a DETACH REQUEST Stimulus , see below for message structure On receipt of an ATTACH REQUEST (see note 2) or Reaction Sends, saves, does, etc. if the action is sending see below for message structure , etc. Message structure Message exchange, etc. (see note 2) a) containing a(n) IE b) indicat

31、ing and back to a) or b) (see note 3) NOTE 1: Text in italics will not appear in TPs and text between is filled in for each TP and may differ from one TP to the next. NOTE 2: All messages are considered as “valid and compatible“ unless otherwise specified in the test purpose. This includes the prese

32、nce of all NAS mandatory IEs as specified in ETSI TS 124 301 1. For better overview of the document there are S1AP messages (ex. DOWNLINK_NAS_TRANSPORT) written with underscore character and NAS messages (ex. ATTACH REQUETS) with space character. NOTE 3: An IE can be embedded into another IE. This i

33、s expressed by indentations, e.g. if Message1 contains IE1 and IE2 where IE1 has IE3 embedded this will be expressed like this: sends/receives Message 1 containing IE1 containing IE3 indicating containing IE2indicating. ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)9 5.2 Test Purposes 5.2.1 PICS references

34、 All PICS items referred in this clause are as specified in ETSI TS 103 530-1 2 unless indicated otherwise by another numbered reference. PICS items are only meant for test selection, therefore only PICS items with status optional or conditional are explicitly mentioned. 5.2.2 S1_MME interface NAS M

35、ME Role 5.2.2.1 Test selection The IUT takes the role of the MME; PICS A.2/1. Test purposes contains S1AP message with NAS-PDU content. S1AP message content with required IEs is present within clause 5.2.3. 5.2.2.2 Elementary procedures for EPS mobility management 5.2.2.2.1 GUTI reallocation group T

36、P_NAS_MME_MGR_01 Standards Reference: ETSI TS 124 301 1, clauses 5.4.1 and 8.2.16 PICS item: PICS A.4/1 Summary: Verify that the IUT can send a GUTI REALLOCATION COMMAND message with all mandatory IEs to indicate GUTI reallocation procedure. Configuration: CF_S1-MME Test purpose: Ensure that the IUT

37、 to indicate a GUTI reallocation procedure, sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type containing a Message_type indicating GUTI REALOCATION COMMAND containing an EPS_mobile_identity. Comments: 5.2.2.

38、2.2 Authentication group TP_NAS_MME_MAU_01 Standards Reference: ETSI TS 124 301 1, clauses 5.4.2 and 8.2.7 PICS item: PICS A.4/2 Summary: Verify that the IUT can send an AUTHENTICATION REQUEST message with all mandatory IEs to indicate authentication procedure. Configuration: CF_S1-MME Test purpose:

39、 Ensure that the IUT to indicate an authentication procedure, sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type containing a Message_type indicating an AUTHENTICATION REQUEST containing a NAS_key_set_identif

40、ier containing a Spare_half_octet containing an Authentication_parameter_RAND containing an Authentication_parameter_AUTN. Comments: Preamble action: Attached procedure is exchanged. ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)10 TP_NAS_MME_MAU_02 Standards Reference: ETSI TS 124 301 1, clauses 5.4.2.2,

41、5.4.2.5 and 8.2.6 PICS item: PICS A.4/2.1 Summary: Verify that the IUT can send an AUTHENTICATION REQUEST message to indicate authentication procedure and in case if authentication response is not valid and the IMSI was used for identification in the initial NAS message the IUT sends AUTHENTICATION

42、REJECT message. Configuration: CF_S1-MME Test purpose: Ensure that the IUT to indicate an authentication procedure, sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type containing a Message_type indicating an A

43、UTHENTICATION REQUEST containing a NAS_key_set_identifier containing a Spare_half_octet containing an Authentication_parameter_RAND containing an Authentication_parameter_AUTN on receipt of an UPLINK_NAS_TRANSPORT (see MI_S1AP_NAS_03) containing a NAS-PDU containing a Protocol_discriminator containi

44、ng a Security_header_type containing a Message_type indicating an AUTHENTICATION RESPONSE containing an Authentication_response_parameter indicating wrong response sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_heade

45、r_type containing a Message_type indicating an AUTHENTICATION REJECT. Comments: Preamble action: Attached procedure is exchanged. ETSI ETSI TS 103 530-2 V1.1.1 (2018-02)11 TP_NAS_MME_MAU_03 Standards Reference: ETSI TS 124 301 1, clauses 5.4.2.6 3, 5.4.2.7 (item c), 8.2.7 and 8.2.18 PICS item: PICS

46、A.4/2.2 and A.4/2.2.1 Summary: Verify that the IUT can send an AUTHENTICATION REQUEST indicating invalid MAC code (in the AUTN parameter) and when receives AUTHENTICATION FAILURE the IUT sends IDENTITY REQUEST to obtain the IMSI from the UE. In case the identification procedure shows an incorrect GU

47、TI/IMSI mapping the IUT sends new AUTHENTICATION REQUEST. Configuration: CF_S1-MME Test purpose: Ensure that the IUT to indicate an authentication procedure, sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type

48、 containing a Message_type indicating an AUTHENTICATION REQUEST containing a NAS_key_set_identifier containing a Spare_half_octet containing an Authentication_parameter_RAND containing an Authentication_parameter_AUTN indicating invalid AUTN code on receipt of an UPLINK_NAS_TRANSPORT (see MI_S1AP_NA

49、S_03) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type containing a Message_type indicating an AUTHENTICATION FAILURE containing an EMM_cause indicating cause #20 “MAC failure“ sends a DOWNLINK_NAS_TRANSPORT (see MI_S1AP_NAS_02) containing a NAS-PDU containing a Protocol_discriminator containing a Security_header_type containing a Message_type indicating an IDENTITY REQUEST containing an Identity_type 2 indicating an IMSI containing a Spare_half_octet on receipt of an UPLINK_NAS_TRANSPOR