ETSI TS 103 544-8-2017 Publicly Available Specification (PAS) Intelligent Transport Systems (ITS) MirrorLink Part 8 Location Data Service (V1 3 0).pdf

1、 ETSI TS 103 544-8 V1.3.0 (2017-10) Publicly Available Specification (PAS); Intelligent Transport Systems (ITS); MirrorLink; Part 8: Location Data Service CAUTION The present document has been submitted to ETSI as a PAS produced by CCC and approved by the ETSI Technical Committee Intelligent Transpo

2、rt Systems (ITS). CCC is owner of the copyright of the document CCC-TS-022 and/or had all relevant rights and had assigned said rights to ETSI on an “as is basis“. Consequently, to the fullest extent permitted by law, ETSI disclaims all warranties whether express, implied, statutory or otherwise inc

3、luding but not limited to merchantability, non-infringement of any intellectual property rights of third parties. No warranty is given about the accuracy and the completeness of the content of the present document. TECHNICAL SPECIFICATION ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)2 Reference DTS/ITS-88

4、-8 Keywords interface, ITS, PAS, smartphone ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The

5、 present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization o

6、f ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware t

7、hat the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following servic

8、es: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shal

9、l not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. Car Connectivity Consortium 2011-2017. All rights reserved. ETSI logo is a Trade Mark of ETSI registered for the benefit of its Members. MirrorLink

10、 is a registered trademark of Car Connectivity Consortium LLC. RFB and VNC are registered trademarks of RealVNC Ltd. UPnP is a registered trademark of UPnP Forum. Other names or abbreviations used in the present document may be trademarks of their respective owners. DECTTM, PLUGTESTSTM, UMTSTMand th

11、e ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks register

12、ed and owned by the GSM Association ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Abbreviations . 5g34 Data Service Definition 6g34.1

13、Location Data Service Version 1.0 . 6g34.2 Location Data Service Version 2.0 . 7g34.3 Location Data Service Version 3.0 . 8g35 SBP Binding . 9g3Annex A (informative): Authors and Contributors . 10g3History 11g3ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)4 Intellectual Property Rights Essential patents IP

14、Rs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or p

15、otentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI

16、. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted

17、and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ET

18、SI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The present document is part 8 of a multi-part deliverable. Full details of the entire series can

19、be found in part 1 i.1. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions).

20、 “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)5 1 Scope The present document is part of the MirrorLinkspecification which specifies an interface for enabling remote user interaction of a mobile device via anoth

21、er device. The present document is written having a vehicle head-unit to interact with the mobile device in mind, but it will similarly apply for other devices, which provide a colour display, audio input/output and user input mechanisms. The present document specifies location service based on SBP

22、(Service Binary Protocol) framework. The service is used to provide better location data in car environments. Note that this service provides high-level abstraction of location compared to com.mirrorlink.GPS service, which focuses on NMEA based GPS data. 2 References 2.1 Normative references Referen

23、ces are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced docu

24、ments which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents

25、 are necessary for the application of the present document. 1 W3C Geolocation API Specification. NOTE: Available at http:/dev.w3.org/geo/api/spec-source.html. 2 ISO/IEC/IEEETM60559:2011 (IEEE-754-2008): “Information technology - Microprocessor Systems - Floating-Point arithmetic“. 2.2 Informative re

26、ferences References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies.

27、 NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject are

28、a. i.1 ETSI TS 103 544-1 (V1.3.0): “Publicly Available Specification (PAS); Intelligent Transport Systems (ITS); MirrorLink; Part 1: Connectivity“. 3 Abbreviations For the purposes of the present document, the following abbreviations apply: GPS Global Positioning System ETSI ETSI TS 103 544-8 V1.3.0

29、 (2017-10)6 4 Data Service Definition 4.1 Location Data Service Version 1.0 /* The specification defines a high-level interface to location * information provided by the vehicle system. The Location service * API itself is agnostic of the underlying location information * sources. Vehicle system sou

30、rces can deliver improved location * information inferred from different methods e.g. dead reckoning, * map matching, involvement of vehicle sensors, differential global * position system etc. if available. * version 1.0 */ SERVICE com.mirrorlink.location /* Structure holding location coordinate. De

31、fault value NaN (Not a * Number) is defined in the IEEE standard 2. All supported * optional elements shall be always present. * Member variables defined in the Coordinates structure have the * same meaning as the member variables defined in Coordinates * interface from W3Cs Geolocation API specific

32、ation 1. * One difference is, that in the present document, member variables * are all optional with the default value of NaN while the W3C API * allows null value for not available data. * When parts of the location object are not available e.g. * due to lost satellite reception, they should be set

33、 to NaN. * A MirrorLink Client should not provide map-matched coordinates. * If available, the MirrorLink Client should use a dead-reckoned * position. */ STRUCTURE Coordinates /* Geographic latitude; a positive value indicates north, a negative * value south. * optional, default NaN, unit decimal d

34、egree, * range -90 to 90 with North positive, uid 0x64f8f3f1 */ DOUBLE latitude; /* Geographic longitude; a positive value indicates east, a negative * value west. * optional, default NaN, unit decimal degree, * range -180 to 180 with East positive, uid 0x7581892a */ DOUBLE longitude; /* Height of t

35、he position above the coordinate systems ellipsoid. * optional, default NaN, unit meter, uid 0x970e9047 */ DOUBLE altitude; /* Accuracy level of the latitude and longitude coordinates. * optional, default NaN, unit meter, uid 0x5ec654de */ DOUBLE accuracy; /* Accuracy level of the altitude informati

36、on. * optional, default NaN, unit meter, uid 0xc28b9440 */ DOUBLE altitudeAccuracy; /* Direction of travel. The heading is counting clockwise, relative * to true north. * optional, default NaN, unit decimal degree, * range 0 to 360, uid 0x813C675D */ DOUBLE heading; /* Magnitude of the horizontal co

37、mponent of current velocity. * optional, default NaN, unit meter per second, uid 0x23234962 */ DOUBLE speed; ; /* This is a high-level representation of geolocation data. The * center location of the vehicles front axle is defined as the * positioning reference point. * mandatory, readable, version

38、1.0, uid 0x572a6461 */ Object GeoLocation /* Location coordinate structure * mandatory, uid 0xbad026d0 */ STRUCTURE coord; ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)7 /* UTC time when the position was acquired. In case the UTC time * associated with the acquisition of the location is unknown, the * Loc

39、ation Data Source shall set the timeStamp value to zero (0). * mandatory, uid 0x59413fd1 */ TIME timeStamp; ; ; 4.2 Location Data Service Version 2.0 /* The new version of the Location Data Service is based on the 1.0 * version, but introduces a set of new objects. * version 2.0 */ SERVICE com.mirro

40、rlink.location : version 1.0 ENUM definedCoordinateSystem /* WGS-84 coordinate system * mandatory */ CS_WGS84 = 0x00000001; /* GCJ-02 coordinate system * optional */ CS_GCJ02 = 0x00000002; /* GCJ-02 coordinate system * optional */ CS_Proprietary = 0x80000000; ; /* This object returns bit flags of su

41、pported coordinate systems * from the Location Data source. * mandatory, readable, version 2.0, uid 0x6f1c2428 */ Object availableCoordinateSystems /* Bit wise OR of all supported coordinate systems by the data * source. Possible coordinate systems are defined in the * definedCoordinateSystem enumer

42、ation. * This object should be accessed before accessing any of the other * objects. A location data source shall support WGS-84, unless the * device is operating in China. * mandatory, uid 0x0885cf07 */ int coordinateSystems; ; /* This object contains the currently used coordinate system from the *

43、 Location Data source. The object can be set from data sink to * change the coordinate system. * It should be accessed before subscribing to the GeoLocation * object. The objects default value should be cs_WGS-84, unless the * device is operating in China, where it may be cs_GCJ02. * If the object i

44、s set to a coordinate system, unknown or not * supported, the location data source shall indicate the location * as not being available. * The coordinate system SHALL NOT be changed, after subscription * to the GeoLocation object. The location data sink may change the * coordinate system if it has n

45、ot subscribed to the GeoLocation * object. * The data source shall honor the selected coordinate system. * mandatory, configurable, version 2.0, uid 0x17ab51db */ Object currentCoordinateSystem /* Provide coordinate system, the source is currently using. * mandatory, uid 0xd2394c6c */ ENUM coordinat

46、eSystem; ; ; ETSI ETSI TS 103 544-8 V1.3.0 (2017-10)8 4.3 Location Data Service Version 3.0 /* The new version of the Location Data Service is based on the 2.0 * version, but changes location obligation within the Coordinates * structure. * version 3.0 */ SERVICE com.mirrorlink.location : version 2.

47、0 /* STRUCTURE holding location coordinate. * Obligation change for latitude and longitude elements, otherwise * identical to Version 2.0. */ STRUCTURE Coordinates /* Geographic latitude. * Obligation change, otherwise identical to Version 2.0. * mandatory, default NaN, unit decimal degree, * range

48、-90 to 90 with North positive, uid 0x64f8f3f1 */ DOUBLE latitude; /* Geographic longitude. * Obligation change, otherwise identical to Version 2.0. * mandatory, default NaN, unit decimal degree, * range -180 to 180 with East positive, uid 0x7581892a */ DOUBLE longitude; /* Height of the position abo

49、ve the coordinate systems ellipsoid. * Identical to Version 2.0. * optional, default NaN, unit meter, uid 0x970e9047 */ DOUBLE altitude; /* Accuracy level of the latitude and longitude coordinates. * Identical to Version 2.0. * optional, default NaN, unit meter, uid 0x5ec654de */ DOUBLE accuracy; /* Accuracy level of the altitude information. * Identical to Version 2.0. * optional, default NaN, unit meter, uid 0xc28b