ETSI TS 122 034-2017 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) High Speed Circuit Switched Data (HSCSD) Stage 1 .pdf

1、 ETSI TS 122 034 V14.0.0 (2017-03) Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); High Speed Circuit Switched Data (HSCSD); Stage 1 (3GPP TS 22.034 version 14.0.0 Release 14) TECHNICAL SPECIFICATION GLOBAL SYSTEM FOR MOBILE COMMUNICATI

2、ONSRETSI ETSI TS 122 034 V14.0.0 (2017-03)13GPP TS 22.034 version 14.0.0 Release 14Reference RTS/TSGS-0122034ve00 Keywords GSM,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but

3、 non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions

4、 of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specifi

5、c network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find

6、 errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm

7、 except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reser

8、ved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by

9、the GSM Association. ETSI ETSI TS 122 034 V14.0.0 (2017-03)23GPP TS 22.034 version 14.0.0 Release 14Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly ava

10、ilable for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web ser

11、ver (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may beco

12、me, essential to the present document. Foreword The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GS

13、M, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of th

14、e ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 122 034 V14.0.0 (2017-03)33GPP TS 22.034 version 14.0.0 Release 14Contents Intellectual Property Rights 2g3Foreword . 2g

15、3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Abbreviations and definitions 6g33.1 Abbreviations . 6g33.2 Definitions 7g34 Description . 7g34.1 General . 7g34.2 Applicability . 7g34.3 General Bearer Services . 7g34.4 Parameters to be indicated and negotiated . 7g34.4.1 Call

16、set-up . 7g34.4.1.1 T services 8g34.4.1.2 NT services . 8g34.4.2 Network initiated modification . 8g34.4.2.1 T services 8g34.4.2.2 NT services . 8g34.4.3 User initiated modification . 9g34.4.3.1 T services 9g34.4.3.2 NT services . 9g34.5 Air Interface Resource Allocation 9g34.5.1 Minimum GERAN Air I

17、nterface Resource Allocation and Allocation Increment . 9g34.5.2 Flexible Air Interface Resource Allocation 9g34.6 Symmetric and asymmetric connections 9g34.6.1 Symmetric connections . 9g34.6.2 Asymmetric connections. 9g34.6.2.1 Asymmetric air interface connection 9g34.6.2.2 Channel coding asymmetry

18、 . 10g34.6.3 Network choice of connection symmetry . 10g34.7 User Equipment/Mobile Equipment requirements . 10g34.8 Mobility Management 10g34.9 Roaming . 10g34.10 Quality of Service . 11g34.10.1 Bit error rate 11g34.10.1.1 GERAN TCH/F Bit Error Rate . 11g34.10.1.2 Overall GBS Bit Error Rate 11g34.10

19、.2 GERAN Radio resource management 11g34.10.3 Call set-up delay . 11g34.10.4 End-to-end delay . 11g34.10.5 Throughput . 11g34.10.6 Network planning and interference levels 11g34.11 Mapping of FNUR to GERAN TCH/F for T services 11g34.12 Mapping of GERAN AIUR to GERAN TCH/F for NT services . 11g34.13

20、GBS MMI aspects 12g34.14 GBS Subscription aspects 12g34.15 GBS charging aspects . 12g34.16 O and M aspects . 12g34.17 Multislot security aspects . 12g35 Exceptional procedures or unsuccessful outcome 13g3ETSI ETSI TS 122 034 V14.0.0 (2017-03)43GPP TS 22.034 version 14.0.0 Release 146 Interworking re

21、quirements . 13g36.1 Service interworking 13g36.1.1 Interworking with supplementary services . 13g36.1.2 Interworking with other services 13g36.2 Network interworking 13g3Annex A (informative): Change history . 14g3History 15g3ETSI ETSI TS 122 034 V14.0.0 (2017-03)53GPP TS 22.034 version 14.0.0 Rele

22、ase 14Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present doc

23、ument, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change con

24、trol. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 122 034 V14.0.0 (2017-03)63GPP TS 22.034 version 14.0.0 Rele

25、ase 141 Scope The present document specifies the Stage 1 description of High Speed Circuit Switched Data (HSCSD). HSCSD is a feature that introduce General Bearer Services and a multislot mechanism is used for user rates that can be achieved with one or more TCH/F. Multislot also defines a flexible

26、use of air interface resources which makes efficient and flexible use of higher user rates feasible. The Multislot mechanism is only applicable to GERAN. At UTRAN radio access parameters used for GBS user data are specified at TS 23.107. 2 References The following documents contain provisions which,

27、 through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the lat

28、est version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 3GPP TS 22.002: “Bea

29、rer Services (BS) supported by a Public Land Mobile Network (PLMN)“. 3 3GPP TS 22.004: “General on supplementary services“. 4 3GPP TS 405.002: “ Multiplexing and multiple access on the radio path“. 3 Abbreviations and definitions 3.1 Abbreviations For the purposes of the present document, the follow

30、ing abbreviations apply: AIUR Air Interface User Rate EDGE Enhanced Data rates for GSM Evolution FNUR Fixed Network User Rate GBS General Bearer Services GERAN GSM/EDGE radio access network HSCSD High Speed Circuit Switched Data MO Mobile Originated MT Mobile TerminatedNT Non Transparent T Transpare

31、nt UE User Equipment (same as MS in GSM specifications) Additional abbreviations can be found in TS 22.905 1. ETSI ETSI TS 122 034 V14.0.0 (2017-03)73GPP TS 22.034 version 14.0.0 Release 143.2 Definitions For the purposes of the present document, the following terms and definitions apply: Fixed Netw

32、ork User Rate: user rate between IWF and the fixed network. Air Interface User Rate: user rate between Mobile Termination and IWF. For T services it is the maximum possible AIUR not including padding. For NT services it is the maximum possible AIUR. maximum possible GERAN AIUR: highest possible GERA

33、N AIUR that the multiple TCH/F can provide, e.g. 2 TCH/F using TCH/F9.6 provides a maximum possible AIUR of 19,2 kbit/s. padding: fill bits needed to adapt the maximum possible AIUR supported by a given number of TCH/F with a given channel coding to a FNUR that is lower than the maximum possible AIU

34、R. 4 Description 4.1 General HSCSD is a feature that introduce General Bearer Services (GBS) and a multislot mechanism is used for user rates that can be achieved with one or more TCH/F. HSCSD also defines mechanisms for the use of air interface resources which makes efficient and flexible use of hi

35、gher user rates feasible. The Multislot mechanism is only applicable to GERAN. 4.2 Applicability GBS shall provide flexible ways of supporting GSM Phase 2, T and NT data services and new data services at the higher rates. Data compression shall be applicable to NT GBS. Supplementary Services applica

36、ble to the General Bearer Services are specified at TS 22.004, 3. 4.3 General Bearer Services The General Bearer Services are defined in TS 22.002 2. The General Bearer Services (GBS) consist of two Bearer Services, and they are as follows: - asynchronous; - synchronous. 4.4 Parameters to be indicat

37、ed and negotiated 4.4.1 Call set-up The parameters to be indicated, and negotiated, if applicable, during the call set-up shall include: - FNUR; - GERAN Channel coding(s) acceptable (for the call); - maximum number of GERAN TCH/F (that the mobile user can accept); - wanted AIUR (desired rate that th

38、e mobile user wants the network to allocate). The wanted AIUR is applicable to NT services only; - indication if the user initiated modification is required, and if so, the network resource needs; - channel coding asymmetry indication. ETSI ETSI TS 122 034 V14.0.0 (2017-03)83GPP TS 22.034 version 14

39、.0.0 Release 14Some of the parameters are only utilised by GERAN. When UTRAN radio access bearer is allocated the values are ignored. The GERAN channel coding(s) acceptable shall be indicated by the mobile at call set-up and is not negotiable. It indicates the GERAN channel coding(s) that may be cho

40、sen by the network for the call. The maximum number of GERAN TCH/F shall be indicated at call set-up. It enables the mobile user to limit the number of GERAN TCH/F used and thus to control an essential parameter for charging. It sets the upper limit of number of TCH/F that the network may allocate t

41、o the mobile. The wanted AIUR (applicable to NT services only) indicates the AIUR that the mobile user wants and which the network shall try to reach but which it is not allowed to exceed. The exception where the network is allowed to exceed the wanted AIUR is when the network can achieve the GERAN

42、AIUR with a lower number of TCH/F, e.g. wanted GERAN AIUR indicated by the mobile is 14,4 kbit/s, GERAN channel codings acceptable are both TCH/F9.6 and TCH/F4.8 and maximum number of TCH/F are 3, then the network shall choose 2 x 9,6 over 3 x 4,8 if a channel coding of TCH/F9.6 is available on two

43、TCH/F. If the user wishes to make use of the user initiated modification procedure, this shall be indicated at the call set-up. It shall be possible to reserve a different FNUR than the AIUR. Channel coding asymmetry indication is only applicable to NT calls where the user has indicated acceptance f

44、or channel coding(s) based on enhanced modulation. In this case the user may indicate preference for channel coding symmetry, downlink biased channel coding asymmetry, or uplink biased channel coding asymmetry. The channel coding asymmetry indication is only applicable in direction UE to network. 4.

45、4.1.1 T services The ME or the network may propose to modify the FNUR. The calling entity may accept or release the call. Autobauding is not allowed. The AIUR is always equal to the FNUR. Fax Group 3 can make use of HSCSD. The GERAN channel coding selected must be one of the channel coding(s) indica

46、ted in the channel coding(s) acceptable parameter, the number of TCH/F selected shall not exceed the maximum number of TCH/F parameter, and the combination of the two shall result in an AIUR that is equal to the FNUR. 4.4.1.2 NT services The ME or the network may propose to modify the FNUR. The call

47、ing entity may accept or release the call. Autobauding is allowed. The wanted AIUR is indicated by the mobile at call set-up. 4.4.2 Network initiated modification 4.4.2.1 T services For transparent calls the radio resource parameters must remain within limits that allow the transparent call to maint

48、ain it is characteristics of fixed end to end throughput and delay. This means that in GERAN the channel coding and the number of TCH/F used may change during the call as long as a channel coding indicated in the channel coding(s) acceptable parameter is used, the maximum number of TCH/F is not exce

49、eded and the AIUR is kept constant. 4.4.2.2 NT services For NT calls the network may modify the number of TCH/F and the channel coding used at GERAN and thus also the AIUR during the call as long as the maximum number of TCH/F, and the channel coding(s) acceptable are all respected. The network shall try to reach the wanted GERAN AIUR indicated, as long as the resource situation allows it. ETSI ETSI TS 122 034 V14.0.0 (2017-03)93GPP TS 22.034 version 14.0.0 Release 144.4.3 User initiated modification The in-call modification feature shall be supported in c