ETSI TS 123 146-2017 Universal Mobile Telecommunications System (UMTS) Technical realization of facsimile Group 3 non-transparent (V14 0 0 3GPP TS 23 146 version 14 0 0 Release 14).pdf

1、 ETSI TS 123 146 V14.0.0 (2017-04) Universal Mobile Telecommunications System (UMTS); Technical realization of facsimile Group 3 non-transparent (3GPP TS 23.146 version 14.0.0 Release 14) TECHNICAL SPECIFICATION ETSI ETSI TS 123 146 V14.0.0 (2017-04)23GPP TS 23.146 version 14.0.0 Release 14Reference

2、 RTS/TSGC-0323146VE00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present

3、 document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI.

4、In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the

5、document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: http

6、s:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be

7、 modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the ben

8、efit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 123 146 V14.0.0 (2017-04)33GPP TS 23.146 version 14.0.0 Releas

9、e 14Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Prop

10、erty Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR sea

11、rches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produ

12、ced by the ETSI 3rdGeneration Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference

13、between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause

14、 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 123 146 V14.0.0 (2017-04)43GPP TS 23.146 version 14.0.0 Release 14Contents Intellectual Property Rights 2g3For

15、eword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definition and abbreviations 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Network architecture 8g34.1 Service definition . 8g34.2 Network architecture 9g35 Reference configuration at the mobile station 9g35.1 FA funct

16、ionality . 10g35.2 UMTS facsimile machine functionality . 10g36 Connection types 10g36.1 Protocol model . 11g36.2 Mobile to mobile calls 12g36.3 Procedure interrupts . 12g36.4 Radio channel modification 12g37 Facsimile adaptor . 12g37.1 Principles of the Facsimile Protocol Adaptation 12g37.2 FA func

17、tionality . 13g37.2.1 Packet elements between FAs . 14g37.2.2 Interactions between and interventions within the FAs 15g37.2.3 BCS phase . 16g37.2.3.1 BCS command/response procedures . 16g37.2.3.2 Compatibility checking . 17g37.2.3.3 Training Check 17g37.2.3.4 Control of transmission rate 18g37.2.4 M

18、essage phase 18g37.2.4.1 Message Transcoding 18g37.2.4.2 Generation of the normal data packet 19g37.2.4.3 Generation of the error correction data packet 19g37.2.4.4 Normal facsimile data . 19g37.2.4.5 Error correction facsimile data 19g37.2.4.6 Controlling of facsimile coded data 20g37.2.4.6.1 Trans

19、mitting Fax Adapter 20g37.2.4.6.2 Receiving Fax Adapter 20g37.2.5 Disconnect procedure . 21g37.2.6 Timeouts . 21g38 Use of terminal adaptation functions 21g38.1 Principles of terminal adaptation functions 21g38.2 Specific TAFs for facsimile service . 22g39 Signalling aspects . 22g39.1 Handling of to

20、nal signals 22g39.2 Call establishment 22g39.2.1 Mobile terminated call 22g39.2.1.1 Speech then facsimile 23g39.2.1.2 Auto answer 23g3ETSI ETSI TS 123 146 V14.0.0 (2017-04)53GPP TS 23.146 version 14.0.0 Release 149.2.2 Mobile originated calls . 23g39.2.2.1 Speech then facsimile 23g39.2.2.2 Auto call

21、ing. 24g39.2.2.3 Manual calling . 24g310 Interworking to fixed networks 25g310.1 Interworking to PSTN 25g310.2 Interworking to ISDN . 25g3Annex A (normative): Structure and contents of the FA protocol elements 26g3A.1 Internet Fax Protocol 26g3A.2 Facsimile UDP Transport Layer Protocol 26g3A.3 User

22、Datagram Protocol . 26g3A.4 Internet Protocol . 27g3A.5 Point to Point Protocol . 27g3A.6 Mapping of FA frames . 27g3Annex B (informative): Abbreviations from ITU-T Recommendation T.30 and T.4 28g3Annex C (informative): Procedure examples . 29g3Annex D (normative): SDL Diagrams 41g3Annex E (normativ

23、e): ASN.1 notation . 79g3Annex F (informative): Change history . 80g3History 81g3ETSI ETSI TS 123 146 V14.0.0 (2017-04)63GPP TS 23.146 version 14.0.0 Release 14Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document defines

24、 the technical realization of facsimile group 3 using non-transparent network support within the 3GPP system. The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, i

25、t will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y

26、the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 123 146 V14.0.0 (2017-04)73GPP TS 23.146 version 14.0.0 Release 141

27、Scope The present document describes the procedures allowing the technical realization of the real time end-to-end facsimile group 3 service within the UMTS PLMN using non-transparent network support according to the definition of the Teleservices 61 and 62 specified in 3GPP TS 22.003. Within the pr

28、esent document particular attention is given to Teleservice “Alternate speech/facsimile group 3“ (Teleservice 61). However, the definitions apply also to Teleservice “Automatic facsimile group 3“ (Teleservice 62) with the exception of all actions concerned with the speech phase. Consequently, in the

29、 following descriptions the term “Teleservice“ denotes both Teleservice 61 and Teleservice 62 as appropriate. NOTE: V.25bis is outdated. References to V.25bis procedures need to be replaced by corresponding procedures based on V.250 and 3GPP TS 27.007. 2 References The following documents contain pr

30、ovisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific ref

31、erence, the latest version applies. 1 3GPP TS 22.003: “Circuit Teleservices supported by a Public Land Mobile Network (PLMN)“. 2 3GPP TR 23.910: “Circuit Switch Data Bearer Services“. 3 3GPP TS 24.008: “Mobile radio interface layer 3 specification“. 4 3GPP TS 27.001: “General on Terminal Adaptation

32、Functions (TAF) for Mobile Stations (MS)“. 5 3GPP TS 27.002: “Terminal Adaptation Functions (TAF) for services using asynchronous bearer capabilities“. 6 3GPP TS 27.007: “AT command set for 3GPP User Equipment(UE)“. 7 3GPP TS 29.007: “3GPP; TSG CN; General requirements on interworking between the Pu

33、blic Land Mobile Network (PLMN) and the Integrated Services Digital Network (ISDN) or Public Switched Telephone Network (PSTN)“. 8 ITU-T Recommendation T.4: “Standardization of group 3 facsimile apparatus for document transmission“. 9 ITU-T Recommendation T.30: “Procedures for document facsimile tra

34、nsmission in the general switched telephone network“. 10 ITU-T Recommendation V.21: “300 bits per second duplex modem standardized for use in the general switched telephone network“. 11 ITU-T Recommendation V.24: “List of definitions for interchange circuits between data terminal equipment (DTE) and

35、 data circuit-terminating equipment (DCE)“. 12 ITU-T Recommendation V.27 ter: “4 800/2 400 bits per second modem standardized for use in the general switched telephone network“. 13 ITU-T Recommendation V.29: “9 600 bits per second modem standardized for use on point-to-point 4-wire leased telephone-

36、type circuits“. 14 ITU-T Recommendation V.17: “A 2-wire modem for facsimile applications with rates up to 14 400 bit/s“. ETSI ETSI TS 123 146 V14.0.0 (2017-04)83GPP TS 23.146 version 14.0.0 Release 1415 ITU-T Recommendation V.250: “Serial asynchronous automatic dialling and control“. 16 ITU-T Recomm

37、endation X.300: “General principles and arrangements for interworking between public data networks, and between public data networks and other networks“. 17 ITU-T Recommendation T.38: “Procedures for real-time Group 3 facsimile communication over IP networks“. 18 ITU-T Recommendation X.680: “Informa

38、tion technology - Abstract Syntax Notation One (ASN.1): Specification of basic notation“. 19 ITU-T Recommendation X.691: “Information technology ASN.1 encoding rules Specification of Packed Encoding Rules (PER)“. 20 IETF RFC 1662: “PPP in HDLC-like Framing“. 21 IETF RFC 1661: “The Point-to-Point Pro

39、tocol (PPP)“. 22 IETF RFC 1570: “PPP LCP Extensions“. 23 IETF RFC 1332: “The PPP Internet Protocol Control Protocol (IPCP)“. 24 IETF RFC 791: “Internet Protocol“. 25 IETF RFC 768: “User Datagram Protocol“. 3 Definition and abbreviations 3.1 Definitions For the purposes of the present document, the f

40、ollowing terms and definitions apply: E-T.38: to use E-T.38 between both the FAs across the radio interface. E-T.38 is based on ITU-T Recommendation T.38, but there are some differences with regards to the packet elements, transcoding methods, and the procedure of controlling signals. The same proce

41、dure as T.38 is used for the structure of the frame and the protocol stack (Refer to the following clause, annex A and T.38 for the details). TAF: TAF usually shows a function of the UE side, but when IWF has the function that is equal to the UE side TAF, TAF is used to express the function of the I

42、WF in the present document. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AAL2 ATM Adaptation Layer type 2 ARQ Automatic Retransmission Request BCS Binary coded signalling CCT Circuit(s) CD Data Call Direction CDMA Code Division Multiple Access CONTP

43、Character Oriented Non-Transparent Protocol DTCH Dedicated Traffic Channel E-T.38 Enhanced T.38 IE Information element IFP Internet Fax Protocol IP Internet ProtocolIWF Interworking Function I/F InterfaceL2RCOP Layer 2 Relay Character Oriented Protocol MAC Medium Access Control (protocol layering co

44、ntext) ETSI ETSI TS 123 146 V14.0.0 (2017-04)93GPP TS 23.146 version 14.0.0 Release 14MMI Man-Machine Interface MT Mobile Terminal PPP Point to Point Protocol PSTN Public Switched Telephone Network RCSD Reverse Call Setup Direction R-FA Reception side facsimile adaptor that does not have TAF capabil

45、ity R-FAX Reception side facsimile RLC Radio Link Control RLP Radio Link Protocol R-TAF Reception side terminal adaptation function SREJ Selective reject TAF Terminal Adapter Function TE Terminal Equipment T-FA Transmission side facsimile adaptor that does not have TAF capability T-FAX Transmission

46、side facsimile T-TAF Transmission side terminal adaptation function UE User Equipment UDP User Datagram Protocol UDPTL Facsimile UDP Transport Layer protocol The abbreviations for the facsimile specific protocol elements and signals are listed in annex B. 4 Network architecture 4.1 Service definitio

47、n The fixed network facsimile group 3 service is an international telematic service for document transmission between two facsimile group 3 terminals. The service specifications are comprised of two parts: - the control procedures described in ITU-T Recommendation T.30; - the document transmission c

48、oding described in ITU-T Recommendation T.4. The UMTS facsimile group 3 Teleservice allows connections between facsimile group 3 terminals using: - a UMTS PLMN as stand-alone facility for mobile-to-mobile communication; - a UMTS PLMN to have access to fixed networks PSTN and/or ISDN for mobile to/fr

49、om fixed network communication. For this Teleservice, the coding of the facsimile document is as per ITU-T Recommendation T.4 and the protocol as per ITU-T Recommendation T.30 both modified within the PLMN as detailed in the present document. The interworking between different networks is based on ITU-T Recommendation X.300. The particular features of this Teleservice are: - it uses point-to-point communication; - the information transfer mode is circuit, duplex, asynchronous; - the information transfer capability is