ETSI TS 125 111-2018 Universal Mobile Telecommunications System (UMTS) Location Measurement Unit (LMU) performance specification User Equipment (UE) positioning in UTRAN (V15 0 0 3.pdf

1、 ETSI TS 125 111 V15.0.0 (2018-07) Universal Mobile Telecommunications System (UMTS); Location Measurement Unit (LMU) performance specification; User Equipment (UE) positioning in UTRAN (3GPP TS 25.111 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 125 111 V15.0.0 (2018-07)13GPP TS

2、25.111 version 15.0.0 Release 15Reference RTS/TSGR-0425111vf00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (0

3、6) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without

4、the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the p

5、resent document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comme

6、nt to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. Th

7、e content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefi

8、t of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 125 111 V1

9、5.0.0 (2018-07)23GPP TS 25.111 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members

10、and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org

11、/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the pre

12、sent document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and

13、/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The p

14、resent document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under

15、http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expressio

16、n of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 111 V15.0.0 (2018-07)33GPP TS 25.111 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g3Introductio

17、n 5g31 Scope 6g32 References 6g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 General . 7g34.1 Main concepts 7g34.2 LMU Classes 7g34.3 U-TDOA architecture . 7g35 LMU radio characteristics 8g35.1 Frequency bands . 8g35.2 Channel arrangement 8g35.3 Reference sensitiv

18、ity level 9g35.4 Dynamic range . 9g35.5 Adjacent Channel Selectivity (ACS) 9g35.6 Blocking characteristics . 9g35.7 Intermodulation characteristics 13g35.8 Spurious emissions . 14g36 LMU measurement requirements . 15g36.1 General . 15g36.2 RRC States supported . 15g36.3 Maximum response times . 15g3

19、6.4 Nominal time accuracy . 15g36.5 Multipath scenarios 16g36.6 Moving scenario . 16g36.7 Cross correlation 16g3Annex A (informative): Change history . 17g3History 18 ETSI ETSI TS 125 111 V15.0.0 (2018-07)43GPP TS 25.111 version 15.0.0 Release 15Foreword This Technical Specification has been produce

20、d by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change

21、 of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. Y the second digit is incremented for all changes of substanc

22、e, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 111 V15.0.0 (2018-07)53GPP TS 25.111 version 15.0.0 Release 15Introduction In order to ensure correctness and consistency o

23、f the specifications (i.e., technical specifications and technical reports) under responsibility of the Technical Specification Groups (TSG) of the 3rdGeneration Partnership Project (3GPP), clear, manageable and efficient mechanisms are necessary to handle version control, change control, document u

24、pdating, distribution and management. Also, the fact that the specifications are/will be implemented by industry almost in parallel with the writing of them requires strict and fast procedures for handling of changes to the specifications. It is very important that the changes that are brought into

25、the standard, from the past, at present and in the future, are well documented and controlled, so that technical consistency and backwards tracing are ensured. The 3GPP TSGs, and their sub-groups together with the Support Team are responsible for the technical content and consistency of the specific

26、ations whilst the Support Team alone is responsible for the proper management of the entire documentation, including specifications, meeting documents, administrative information and information exchange with other bodies. ETSI ETSI TS 125 111 V15.0.0 (2018-07)63GPP TS 25.111 version 15.0.0 Release

27、151 Scope The present document establishes the Location Measurement Unit (LMU) minimum RF characteristics of the FDD mode of UTRA. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either spe

28、cific (identified by date of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-

29、specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 25.104: “Base Station (BS) radio transmission and reception (FDD)”. 2 3GPP TS 45.004: “Modulation”. 3 3GPP TS 25.141: “Base Station (BS) conformance testing (FDD)”. 4 3G

30、PP TR 25.942: “Radio Frequency (RF) system scenarios”. 5 3GPP TR 21.905: “Vocabulary for 3GPP Specifications”. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 21.905 5 and the following apply. A term defined in the prese

31、nt document takes precedence over the definition of the same term, if any, in TR 21.905 5. Mean power: When applied to a W-CDMA modulated signal this is the power (transmitted or received) in a bandwidth of at least (1+ ) times the chip rate of the radio access mode. The period of measurement shall

32、be at least one timeslot unless otherwise stated. NOTE: The roll-off factor is defined in clause 6.8.1 of 1. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in TR 21.905 5 and the following apply. An abbreviation defined in the present document takes precedence ov

33、er the definition of the same abbreviation, if any, in TR 21.905 5. ACS Adjacent Channel Selectivity BS Base Station BER Bit Error Ratio BLER Block Error Ratio CW Continuous Wave (unmodulated signal) DL Down Link (forward link) FDD Frequency Division Duplexing GSM Global System for Mobile Communicat

34、ions LMU Location Measurement Unit UARFCN UTRA Absolute Radio Frequency Channel Number UE User Equipment UL Up Link (reverse link) ETSI ETSI TS 125 111 V15.0.0 (2018-07)73GPP TS 25.111 version 15.0.0 Release 15U-TDOA Uplink Time Difference Of Arrival WCDMA Wideband Code Division Multiple Access 4 Ge

35、neral 4.1 Main concepts The LMU is either located as a separate unit in an existing network or typically located at Node B or BTS sites. Therefore the LMU radio requirements assume that the isolation between the LMU and any other network to be protected is to be at least 30dB. The communication link

36、 between LMU and Stand-Alone SMLC is not a radio interface over the air. Requirements in this document therefore do not cover the situation when the LMU is transmitting over the air on this interface between LMU and Stand-Alone SMLC. 4.2 LMU Classes The requirements in this specification apply to Wi

37、de Area LMUs and Medium Range LMUs. Wide Area LMUs are characterised by requirements derived from Macro Cell scenarios with an LMU to UE minimum coupling loss equal to 70 dB. Medium Range LMUs are characterised by requirements derived from Micro Cell scenarios with an LMU to UE minimum coupling loss

38、 equal to 53 dB. For Pico Cell scenarios, the location of the BS provides sufficient accuracy; therefore, a Local Area LMUs class is not specified. 4.3 U-TDOA architecture A sample architecture is shown in Figure 3.1 depicting the LMUs relationship with other network elements. The LMU is typically l

39、ocated at the Node B. The LMUs communicate with the SMLC that distributes UTDOA reference data from the reference LMU to other cooperating LMUs when performing UE positioning. ETSI ETSI TS 125 111 V15.0.0 (2018-07)83GPP TS 25.111 version 15.0.0 Release 15Figure 3.1: Example of UTDOA deployment 5 LMU

40、 radio characteristics An LMU performs BS receiver functions to obtain reference data for use at a cooperating LMU. The following clause describes the required LMU radio characteristics when performing these functions. 5.1 Frequency bands a) The LMU is designed to operate in the following bands: Tab

41、le 4.1: Frequency bands Operating Band UL Frequencies UE transmit, LMU receive I 1920 1980 MHz II 1850 -1910 MHz III 1710-1785 MHIV 1710-1755 MHz V 824 849MHz VI 830-840 MHz VII 2500 2570 MHz VIII 880 915 MHz IX 1749.9 1784.9 MHz X 1710-1770 MHb) Deployment in other frequency bands is not precluded

42、5.2 Channel arrangement The channel arrangement shall be as specified in Section 5.4 of 1. Node BNode BStand-AloneSMLCRNCRNCMSCSGSNIubIubIupcIupcLMULMULMULMULMUTypically located atNodeBETSI ETSI TS 125 111 V15.0.0 (2018-07)93GPP TS 25.111 version 15.0.0 Release 155.3 Reference sensitivity level Usin

43、g the reference measurement channel specification in TS 25.104 Annex A 1, the reference sensitivity level and performance of the LMU shall be as specified in Table 4.2. Table 4.2: LMU reference sensitivity levels LMU Class Reference measurement channel data rate LMU sensitivity level (dBm) BER Wide

44、Area LMU 12.2 kbps -121 BER shall not exceed 0.001 Medium Range LMU 12.2 kbps -111 BER shall not exceed 0.001 5.4 Dynamic range Receiver dynamic range is the receiver ability to handle a rise of interference in the reception frequency channel. The receiver shall fulfil a specified BER requirement fo

45、r a specified sensitivity degradation of the wanted signal in the presence of an interfering AWGN signal in the same reception frequency channel. The BER shall not exceed 0.001 for the parameters specified in Table 4.3. Table 4.3: Dynamic range Parameter Level Wide Area LMU Level Medium Range LMU Un

46、it Reference measurement channel data rate 12.2 12.2 kbps Wanted signal mean power -91 -81 dBmInterfering AWGN signal -73 -63 dBm/3.84 MHz 5.5 Adjacent Channel Selectivity (ACS) Adjacent channel selectivity (ACS) is a measure of the LMU receiver ability to receive a wanted signal at its assigned cha

47、nnel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the LMU receiver filter attenuation on the assigned channel frequency to the receiver filter attenuation on the adjacent channel(s). The int

48、erference signal is offset from the wanted signal by the frequency offset Fuw. The interference signal shall be a W-CDMA signal as specified in Annex C of TS 25.104 1. The BER shall not exceed 0.001 for the parameters specified in Table 4.4. Table 4.4: LMU Adjacent channel selectivity Parameter Leve

49、l Wide Area LMU Level Medium Range LMU Unit Data rate 12.2 12.2 kbps Wanted signal mean power -115 -105 dBmInterfering signal mean power -52 -42 dBm Fuw offset (Modulated) 5 5 MHz 5.6 Blocking characteristics The blocking characteristics are a measure of the LMU receiver ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the adjacent channels. The performance as specified in Table 4.5-4.10 shall be met with a wanted and an interfering signal c