ETSI TS 125 116-2018 Universal Mobile Telecommunications System (UMTS) UTRA repeater radio transmission and reception (LCR TDD) (V15 0 0 3GPP TS 25 116 version 15 0 0 Release 15).pdf

1、 ETSI TS 125 116 V15.0.0 (2018-07) Universal Mobile Telecommunications System (UMTS); UTRA repeater radio transmission and reception (LCR TDD) (3GPP TS 25.116 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 125 116 V15.0.0 (2018-07)13GPP TS 25.116 version 15.0.0 Release 15Reference R

2、TS/TSGR-0425116vf00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present d

3、ocument can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In

4、 case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the do

5、cument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:

6、/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be m

7、odified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trade

8、marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 125 116 V15.0.0 (2018-07)23GPP TS 25.116 version 15.0

9、.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI S

10、R 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no inv

11、estigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present docum

12、ent may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks

13、in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical spec

14、ifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Mo

15、dal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are

16、 NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 116 V15.0.0 (2018-07)33GPP TS 25.116 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definitions, symbols and

17、abbreviations . 6g33.1 Definitions 6g33.2 Symbols 7g33.3 Abbreviations . 7g34 General . 7g34.1 Relationship between Minimum Requirements and Test Requirements 8g34.2 Regional requirements 9g35 Frequency bands and channel arrangement 11g35.1 General . 11g35.2 Frequency bands . 11g35.3 TX-RX frequency

18、 separation . 11g35.4 Channel arrangement 11g35.4.1 Channel spacing 11g35.4.2 Channel raster . 11g35.4.3 Channel number 11g36 Output power 11g36.1 Maximum output power . 12g36.1.1 Minimum Requirements . 12g37 Frequency stability . 12g37.1 Minimum requirement 12g38 Out of band gain . 12g38.1 Minimum

19、requirement 12g39 Unwanted emission 13g39.1 Spectrum emission mask 13g39.2 Spurious emissions . 15g39.2.1 Mandatory Requirements 15g39.2.1.1 Spurious emissions (Category A) 15g39.2.1.1.1 Minimum Requirement . 15g39.2.1.2 Spurious emissions (Category B) 15g39.2.1.2.1 Minimum Requirement . 16g39.2.2 C

20、o-existence with GSM 900 . 16g39.2.2.1 Operation in the same geographic area . 16g39.2.2.1.1 Minimum Requirement . 16g39.2.2.2 Co-located base stations 16g39.2.2.2.1 Minimum Requirement . 16g39.2.3 Co-existence with DCS 1800 17g39.2.3.1 Operation in the same geographic area . 17g39.2.3.1.1 Minimum R

21、equirement . 17g39.2.3.2 Co-located base stations 17g39.2.3.2.1 Minimum Requirement . 17g39.2.4 Co-existence with UTRA-FDD 17g39.2.4.1 Operation in the same geographic area . 17g39.2.4.1.1 Minimum Requirement . 18g39.2.4.2 Co-located base stations 18g39.2.4.2.1 Minimum Requirement . 18g3ETSI ETSI TS

22、 125 116 V15.0.0 (2018-07)43GPP TS 25.116 version 15.0.0 Release 159.2.5 Co-existence with unsynchronised TDD 19g39.2.5.1 Operation in the same geographic area . 19g39.2.5.1.1 Minimum Requirement . 19g39.2.5.2 Co-located base stations 19g39.2.5.2.1 Minimum Requirement . 19g310 Modulation accuracy 20

23、g310.1 Error Vector Magnitude . 20g310.1.1 Minimum requirement 20g310.2 Peak code domain error 20g310.2.1 Minimum requirement 20g311 Input intermodulation . 20g311.1 General requirement . 20g311.1.1 Minimum requirement 20g312 Output intermodulation 21g312.0 General . 21g312.1 Minimum requirement 21g

24、313 Adjacent Channel Rejection Ratio (ACRR) . 21g313.1 Definitions and applicability 21g313.2 Co-existence with UTRA . 21g313.2.1. Minimum Requirements . 21g314 Timing Accuracy 22g314.1 Minimum requirement 22g3Annex A (normative): Environmental requirements for the Repeater equipment 23g3Annex B (in

25、formative): Change history . 24g3History 25g3ETSI ETSI TS 125 116 V15.0.0 (2018-07)53GPP TS 25.116 version 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work wit

26、hin the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG

27、for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes ha

28、ve been incorporated in the document. ETSI ETSI TS 125 116 V15.0.0 (2018-07)63GPP TS 25.116 version 15.0.0 Release 151 Scope The present document establishes the minimum RF characteristics of LCR TDD Repeater. 2 References The following documents contain provisions which, through reference in this t

29、ext, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the

30、case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 ITU-R Recommendation SM.329, “Unwanted emissions

31、 in the spurious domain“. 3 ITU-R Recommendation M.1545: “Measurement uncertainty as it applies to test limits for the terrestrial component of International Mobile Telecommunications-2000”. 4 3GPP TS 25.153: “LCR TDD Repeater conformance testing” 5 3GPP TR 25.942: “RF system scenarios“. 6 IEC 60721

32、-3-3 (2002): “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weather protected locations“. 7 IEC 60721-3-4 (1995): “Classification of environmental conditions - Part 3: Classification of gr

33、oups of environmental parameters and their severities - Section 4: Stationary use at non-weather protected locations“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 21.905 1 and the following apply. A term def

34、ined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 1. Carrier: The modulated waveform conveying the LCR TDD physical channels Channel bandwidth: The RF bandwidth supporting a single LCR TDD RF carrier with the transmission bandwidth configured in

35、 the uplink or downlink of a cell. The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF requirements. Channel edge: The lowest and highest frequency of the LCR TDD carrier, separated by the channel bandwidth. Donor coupling loss: is the coupling loss be

36、tween the repeater and the donor base station. Downlink: Signal path where base station transmits and mobile receives. Maximum output power, Pmax: This is the mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition. ETSI ETSI TS 125 116 V15.0.0

37、 (2018-07)73GPP TS 25.116 version 15.0.0 Release 15Output power, Pout: This is the mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to the nominal load impedance of the transmitter. Pass band: The repeater can have one or several pass bands. The pass band

38、is the frequency range that the repeater operates in with operational configuration. This frequency range can correspond to one or several consecutive nominal channels. If they are not consecutive each subset of channels shall be considered as an individual pass band. Rated output power: Rated outpu

39、t power of the repeater is the mean power level per carrier that the manufacturer has declared to be available at the antenna connector. Repeater: A device that receives, amplifies and transmits the radiated or conducted RF carrier both in the down-link direction (from the base station to the mobile

40、 area) and in the up-link direction (from the mobile to the base station) Transmission bandwidth: Bandwidth of an instantaneous transmission from a UE or BS, measured in Resource Block units. Transmission bandwidth configuration: The highest transmission bandwidth allowed for uplink or downlink in a

41、 given channel bandwidth, measured in Resource Block units. Uplink: Signal path where mobile transmits and base station receives. 3.2 Symbols For the purposes of the present document, the following symbols apply: BWChannelChannel bandwidth BWConfigTransmission bandwidth configuration, expressed in M

42、Hz. BWMeasMeasurement bandwidth BWSignalBandwidth of the repeater input signal filling the repeater pass band FDL_low The lowest frequency of the downlink operating band FDL_high The highest frequency of the downlink operating band FUL_low The lowest frequency of the uplink operating band FUL_high T

43、he highest frequency of the uplink operating band f_offset_PB Distance from the channel edge frequency of the first or last channel in the pass band NDLDownlink LARFCN NOffs-DLOffset used for calculating downlink LARFCN NOffs-ULOffset used for calculating uplink LARFCN NRBTransmission bandwidth conf

44、iguration, expressed in units of resource blocks NULUplink LARFCN Pmax Maximum output power Pout Output power 3.3 Abbreviations For the purposes of the present document, the abbreviations given in TR 21.905 1 and the following apply. An abbreviation defined in the present document takes precedence o

45、ver the definition of the same abbreviation, if any, in TR 21.905 1. ACRR Adjacent Channel Rejection Ratio BS Base Station LARFCN LCR TDD Absolute Radio Frequency Channel Number PB Pass Band 4 General This specification applies only to LCR TDD repeaters. Unless otherwise stated, all requirements in

46、this specification apply to both the up-link and down-link directions. ETSI ETSI TS 125 116 V15.0.0 (2018-07)83GPP TS 25.116 version 15.0.0 Release 154.1 Relationship between Minimum Requirements and Test Requirements The Minimum Requirements given in this specification make no allowance for measure

47、ment uncertainty. The test specification TS 25.153 section 4 defines Test Tolerances. These Test Tolerances are individually calculated for each test. The Test Tolerances are used to relax the Minimum Requirements in this specification to create Test Requirements. The measurement results returned by

48、 the Test System are compared - without any modification - against the Test Requirements as defined by the shared risk principle. The Shared Risk principle is defined in ITU-R M.1545 3. ETSI ETSI TS 125 116 V15.0.0 (2018-07)93GPP TS 25.116 version 15.0.0 Release 154.2 Regional requirements Some requ

49、irements in the present document may only apply in certain regions. Table 4.2-1 lists all requirements that may be applied differently in different regions. Table 4.2-1: List of regional requirements ETSI ETSI TS 125 116 V15.0.0 (2018-07)103GPP TS 25.116 version 15.0.0 Release 15Clause number Requirement Comments 5.2 Channel bandwidth Some channel bandwidths may be applied regionally. 5.3 Frequency bands Some bands may be applied regionally. 5.4 Channel arrangement The requirement is applied according to what frequency bands in Clause 5.3 that are