ETSI TS 125 432-2016 Universal Mobile Telecommunications System (UMTS) UTRAN Iub interface signalling transport (V13 0 0 3GPP TS 25 432 version 13 0 0 Release 13)《通用移动通信系统(UMTS) UT.pdf

1、 ETSI TS 1Universal Mobile TelUTRAN Iub in(3GPP TS 25.4TECHNICAL SPECIFICATION125 432 V13.0.0 (2016elecommunications System (interface: signalling transport.432 version 13.0.0 Release 1316-01) (UMTS); ort 13) ETSI ETSI TS 125 432 V13.0.0 (2016-01)13GPP TS 25.432 version 13.0.0 Release 13Reference RT

2、S/TSGR-0325432vd00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present do

3、cument can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In

4、case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the doc

5、ument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.ets

6、i.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified wit

7、hout the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its M

8、embers. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 125 432 V13.0.0 (2016-01)23GPP TS 25.432 version 13.0.0 Release 13Intellect

9、ual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (

10、IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has be

11、en carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3

12、rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMT

13、S, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI

14、 Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 432 V13.0.0 (2016-01)33GPP TS 25.432 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal

15、 verbs terminology 2g3Foreword . 4g31 Scope 5g32 References 5g33 Definitions, symbols and abbreviations . 6g33.1 Definitions 6g33.2 Symbols 6g33.3 Abbreviations . 6g34 Data Link Layer . 6g34.1 ATM Transport Option 6g34.1.1 Protection switching at ATM Layer . 6g34.2 Data Link Layer for IP Transport O

16、ption . 6g35 NBAP signalling bearer 7g35.1 Introduction 7g35.2 Signalling bearer in case of ATM Transport Option 7g35.3 Signalling bearer in case of IP Transport Option . 7g3Annex A (informative): Change history . 9g3History 10g3ETSI ETSI TS 125 432 V13.0.0 (2016-01)43GPP TS 25.432 version 13.0.0 Re

17、lease 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document

18、, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control.

19、 y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 432 V13.0.0 (2016-01)53GPP TS 25.432 version 13.0.0 Release 1

20、31 Scope The present document specifies the signalling transport related to NBAP signalling to be used across the Iub Interface. The Iub interface is a logical interface for the interconnection of Node B and Radio Network Controller (RNC) components of the UMTS Terrestrial Radio Access Network (UTRA

21、N) for the UMTS system. The radio network control signalling between these nodes is based on the Node B application part (NBAP). 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specifi

22、c (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific

23、 reference implicitly refers to the latest version of that document in the same Release as the present document. 1 ITU-T Recommendation Q.2100 (1994-07): “B-ISDN signalling ATM adaptation layer (SAAL) overview description“. 2 ITU-T Recommendation Q.2130 (1994-07): “B-ISDN signalling ATM adaptation l

24、ayer Service specific coordination function for support of signalling at the user network interface (SSCFUNI)“. 3 ITU-T Recommendation Q.2110 (1994-07): “B-ISDN ATM adaptation layer Service specific connection oriented protocol (SSCOP)“. 4 ITU-T Recommendation I.363.5 (1996-08): “B-ISDN ATM Adaptati

25、on LayerSpecification : Type 5 AAL“. 5 ITU-T Recommendation I.361 (1995-11): “B-ISDN ATM layer specification“. 6 ITU-T Recommendation I.630 (1999-02): “ATM protection switching“. 7 IETF RFC 2960 (2000-10): “Stream Control Transmission Protocol“. 8 IETF RFC 2460 (1998-12): “Internet Protocol, Version

26、 6 (IPv6) Specification“. 9 IETF RFC 791 (1981-09): “Internet Protocol“. 10 IETF RFC 2474 (1998-12): “Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers“. 11 IETF RFC 1661 (1994-07): “The Point-to-Point Protocol (PPP)“. 12 IETF RFC 1662 (1994-07): “PPP in HDLC-li

27、ke Framing“. 13 IETF RFC 2507 (1999-02): “IP header compression“. 14 IETF RFC 1990 (1996-08): “The PPP Multilink Protocol (MP)“. 15 IETF RFC 2686 (1999-09): “The Multi-Class Extension to Multi-Link PPP“. 16 IETF RFC 2509 (1999-02): “IP Header Compression over PPP“. 17 IETF RFC 3153 (2001-08): “PPP M

28、ultiplexing“. 18 IETF RFC 2364 (1998-07): “PPP over AAL5“. ETSI ETSI TS 125 432 V13.0.0 (2016-01)63GPP TS 25.432 version 13.0.0 Release 1319 IETF RFC 3031 (2001-01): “Multiprotocol Label Switching Architecture“. 20 IETF RFC 3309 (2002-09): “Stream Control Transmission Protocol (SCTP) Checksum Change

29、“. 21 3GPP TS 25.433: “UTRAN Iub interface Node B Application Part (NBAP) signalling“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: IP UTRAN node: An UTRAN Node supporting the IP Transport Option 3.2 Sym

30、bols (void) 3.3 Abbreviations AAL ATM Adaptation Layer ATM Asynchronous Transfer Mode HDLC High-level Data Link Control IP Internet Protocol NBAP Node B Application Part PPP Point-to-Point ProtocolRNC Radio Network Controller SAAL Signalling ATM Adaptation Layer SCTP Stream Control Transmission Prot

31、ocol SSCF Service Specific Coordination Function SSCOP Service Specific Connection Oriented Protocol UNI User-Network Interface 4 Data Link Layer 4.1 ATM Transport Option ATM shall be used in the radio network control plane according to ITU-T Rec. I.361 5. 4.1.1 Protection switching at ATM Layer If

32、redundancy of pathways at ATM layer between RNC and Node B is supported, it shall be implemented using ATM Protection Switching according to ITU-T Rec. I.630 6. 4.2 Data Link Layer for IP Transport Option A RNC or Node B supporting IP Transport Option shall support the PPP protocol with HDLC framing

33、 (IETF RFC 1661 11, IETF RFC 1662 12). NOTE: This does not preclude the single implementation and use of any other L2/L1 protocols (e.g. PPPMux/AAL5/ATM (IETF RFC 3153 17, IETF RFC 2364 18), PPP/AAL2/ATM, Ethernet, MPLS/ATM (IETF RFC 3031 19), etc.) fulfilling the UTRAN requirements towards the uppe

34、r layers. ETSI ETSI TS 125 432 V13.0.0 (2016-01)73GPP TS 25.432 version 13.0.0 Release 13A RNC or Node B supporting IP transport option and having interfaces connected via slow bandwidth PPP links like E1/T1/J1 shall also support IP Header Compression (IETF RFC 2507 13) and the PPP extensions ML/MC-

35、PPP (IETF RFC 1990 14, IETF RFC 2686 15). In this case, negotiation of header compression (IETF RFC 2507 13) over PPP shall be performed via (IETF RFC 2509 16). 5 NBAP signalling bearer 5.1 Introduction The Signalling Bearer for NBAP (TS 25.433 21) is a point-to-point protocol. There may be multiple

36、 point-to-point links between an RNC and a Node B. As shown in figure 1, the standard allows operators to choose one out of two protocol suites for transporting the NBAP messages. NodeB Application Part (NBAP) AAL Type 5 SSCF-UNI SSCOP NodeB Application Part (NBAP) Data Link Layer Physical Layer IP

37、SCTP Physical Layer ATM Protocol Suite for ATM Transport Option Protocol Suite for IP Transport Option Figure 1: Iub NBAP Signalling Transport 5.2 Signalling bearer in case of ATM Transport Option The signalling bearer in the Radio Network Control Plane is SAAL-UNI (ITU-T Rec. Q.2100 1) over ATM. Th

38、e protocols to be used to support NBAP signalling are SSCF-UNI (ITU-T Rec. Q.2130 2) on top of SSCOP (ITU-T Rec. Q.2110 3) and AAL Type 5 (ITU-T Rec. I.363.5 4). 5.3 Signalling bearer in case of IP Transport Option SCTP (IETF RFC 2960 7) over IP shall be supported as the transport for NBAP signallin

39、g bearer on Iub Interface. A RNC equipped with the SCTP stack option shall initiate the INIT procedure for establishing association. The data link layer is as specified in chapter 4.2. The checksum method specified in IETF RFC 3309 20 shall be used instead of the method specified in IETF RFC 2960 (7

40、). An IP UTRAN node shall support IPv6 (IETF RFC 2460 8). The support of IPv4 (IETF RFC 791 9) is optional. NOTE: This does not preclude single implementation and use of IPv4. IP dual stack is recommended for the potential transition period from IPv4 to IPv6 in the transport network. ETSI ETSI TS 12

41、5 432 V13.0.0 (2016-01)83GPP TS 25.432 version 13.0.0 Release 13Each signalling bearer between the RNC and Node B shall correspond to one single SCTP stream in UL and one single SCTP stream in DL direction, both streams belonging to the same SCTP association. IP Differentiated Services code point ma

42、rking (IETF RFC 2474 10) shall be supported. The Diffserv code point may be determined from the application parameters. ETSI ETSI TS 125 432 V13.0.0 (2016-01)93GPP TS 25.432 version 13.0.0 Release 13Annex A (informative): Change history Date / TSG TSG Doc. CR Rev Subject/Comment New 12/2008 - - - Cr

43、eation of Rel-8 version based on v7.1.0 8.0.0 12/2009 - - - Creation of Rel-9 version based on v8.0.0 9.0.0 SP-49 SP-100629 Clarification on the use of References (TS 21.801 CR#0030) 9.0.1 03/2011 Creation of Rel-10 version based on v9.0.1 10.0.0 52 RP-110685 0008 1 Correction to the References 10.1.0 09/2012 Update to Rel-11 version (MCC) 11.0.0 09/2014 Update to Rel-12 version (MCC) 12.0.0 12/2015 Update to Rel-13 version (MCC) 13.0.0 ETSI ETSI TS 125 432 V13.0.0 (2016-01)103GPP TS 25.432 version 13.0.0 Release 13History Document history V13.0.0 January 2016 Publication