ETSI TS 125 460-2016 Universal Mobile Telecommunications System (UMTS) UTRAN Iuant interface General aspects and principles (V13 0 0 3GPP TS 25 460 version 13 0 0 Release 13)《通用移动通.pdf

1、 ETSI TS 1Universal Mobile TelUTRAN Iuant interfa(3GPP TS 25.4TECHNICAL SPECIFICATION125 460 V13.0.0 (2016elecommunications System (face: General aspects and pri.460 version 13.0.0 Release 1316-01) (UMTS); rinciples 13) ETSI ETSI TS 125 460 V13.0.0 (2016-01)13GPP TS 25.460 version 13.0.0 Release 13R

2、eference RTS/TSGR-0325460vd00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The

3、 present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization o

4、f ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware t

5、hat the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:

6、/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be m

7、odified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benef

8、it of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 125 460 V13.0.0 (2016-01)23GPP TS 25.460 version 13.0.0 Release

9、13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Proper

10、ty Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searc

11、hes, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produce

12、d by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference betwe

13、en GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2

14、of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 460 V13.0.0 (2016-01)33GPP TS 25.460 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword

15、 . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 5g32 References 5g33 Abbreviations . 5g34 General aspects . 6g34.1 Introduction 6g34.2 Iuant interface general principles . 6g34.3 Iuant interface specification objectives 6g34.4 Iuant interface characteristics . 6g35 Functions of the Iuant inte

16、rface protocols 7g35.1 Physical layer functions 7g35.2 Data link layer functions 7g35.3 Application layer functions 8g35.3.1 Control of RET antennas 8g35.3.2 Application software and configuration data download . 8g35.3.3 Alarm reporting 8g35.3.4 Operator specific data storage . 8g35.3.5 Control of

17、Tower Mounted Amplifiers (TMAs) . 8g36 Other Iuant interface specifications 9g36.1 UTRAN Iuant interface: Layer 1 (TS 25.461) 9g36.2 UTRAN Iuant interface: Signalling Transport (TS 25.462) . 9g36.3 RETAP specification (TS 25.463) 9g36.4 Summary of UTRAN Iuant interface Technical Specifications . 9g3

18、6.5 UTRAN Iuant interface: Application part specification (TS 25.466) . 9g3Annex A (informative): OSI model overview . 10g3Annex B (informative): Change History 11g3History 12g3ETSI ETSI TS 125 460 V13.0.0 (2016-01)43GPP TS 25.460 version 13.0.0 Release 13Foreword This Technical Specification has be

19、en produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identify

20、ing change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes o

21、f substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 460 V13.0.0 (2016-01)53GPP TS 25.460 version 13.0.0 Release 131 Scope The present document is an introduction to

22、the 3GPP TS 25.46x series of Technical Specifications that define the Iuant Interface for UMTS and E-UTRAN. The logical Iuant interface is a Node B/eNB internal interface between the implementation specific O - The Data Link Layer (Layer 2) for the Signalling Transport uses a specific class of the H

23、DLC standard as defined in ISO/IEC 13239 5; - The Application Layer (Layer 7) defines the data payload format and the required command set. This layer is called the “Iuant: Application Part“. This compact model for the control interface provides an efficient protocol stack suitable for implementatio

24、n on a single embedded micro-controller. 4.3 Iuant interface specification objectives The Iuant interface specifications shall facilitate the following: - Controlling the tilting of RET antennas remotely from the O - Indicating of TMA alarms and optionally controlling the gain of TMAs remotely from

25、the O - Interfacing a mix of RET antennas, TMAs and Node Bs from different vendors; - Providing RET or TMAs functionality in the UTRAN/E-UTRAN accompanied by an appropriate set of signalling commands and control parameters - Support of error and alarm handling. 4.4 Iuant interface characteristics Th

26、e Iuant interface has a protocol structure as shown below in figure 4.4.1. ETSI ETSI TS 125 460 V13.0.0 (2016-01)73GPP TS 25.460 version 13.0.0 Release 13O - An addressing scheme; - A master/slave relationship whereby the primary device controls the half duplex timing; - A message checksum scheme to

27、 protect from transmission errors; - A message sequence numbering scheme which protects layer 7 from: ETSI ETSI TS 125 460 V13.0.0 (2016-01)83GPP TS 25.460 version 13.0.0 Release 13- Duplicated messages; - Deleted messages; - Receiving messages in the wrong order. - A flow control mechanism protecti

28、ng each device from being overrun by messages. These functions provide layer 7 with a safe full-duplex connection between the primary device and any secondary device. This full duplex connection allows both the primary and secondary device to transmit layer 7 messages to the opposite device of the c

29、onnection, whenever they need to. Actual delivery time on layer 2 will depend on the layer 2 polling frequency, which is chosen by the primary device. 5.3 Application layer functions The list of functions on the Iuant interface is the following: - Control of RET antennas; - Application software and

30、configuration data download; - Alarm Reporting; - Operator specific data storage; - Control of Tower Mounted Amplifiers (TMAs). 5.3.1 Control of RET antennas A RET device provides means to adjust the electrical tilt of one or multiple antennas. The set of procedures to control RET antennas provides

31、means to control the electrical tilt of one or more RET antennas remotely. The procedures are defined in TS 25.466 7. 5.3.2 Application software and configuration data download The interface provides means for downloading new application software and configuration data to a secondary device. The sup

32、port of application software download to a secondary device is optional. If a secondary device supports application software download, it shall reset itself and start running the new application software automatically after the completed download. Further details on the software download procedure (

33、e.g. the different states of the secondary device and the supported elementary procedures in these states) are described in subclause 6.1 of TS 25.466 7. 5.3.3 Alarm reporting The secondary device reports every change in error status after subscription for alarm reporting by transmitting alarm messa

34、ges to the primary device. Alarm information can also be interrogated in the application layer. 5.3.4 Operator specific data storage The secondary device provides means for storage of operator specific data, e.g. inventory information. 5.3.5 Control of Tower Mounted Amplifiers (TMAs) The TMA device

35、provides means to indicate alarms and optionally to adjust the gain of TMAs. The set of procedures to control TMAs are defined in TS 25.466 7. ETSI ETSI TS 125 460 V13.0.0 (2016-01)93GPP TS 25.460 version 13.0.0 Release 136 Other Iuant interface specifications 6.1 UTRAN Iuant interface: Layer 1 (TS

36、25.461) TS 25.461 2 specifies the standards allowed for implementation of Layer 1 (physical layer) on the Iuant interface. 6.2 UTRAN Iuant interface: Signalling Transport (TS 25.462) TS 25.462 3 specifies the signalling transport related to RETAP and TMAAP signalling to be used across the Iuant inte

37、rface. 6.3 RETAP specification (TS 25.463) Void. 6.4 Summary of UTRAN Iuant interface Technical Specifications The relationship between the technical specifications that define the UTRAN Iuant interface is shown in figure 6.4.1. RETAP TMAAP TS 25.466 Transport Layer TS 25.461 Radio Network Layer Iua

38、nt Transport TS 25.462 Physical Layer Figure 6.4.1: Iuant Interface Technical Specifications 6.5 UTRAN Iuant interface: Application part specification (TS 25.466) TS 25.466 7 specifies protocols for application part to be used over the Iuant interface. ETSI ETSI TS 125 460 V13.0.0 (2016-01)103GPP TS

39、 25.460 version 13.0.0 Release 13Annex A (informative): OSI model overview Figure A.1: Relevant OSI model layers Figure A.1 shows the relevant OSI model layers and the communication paths between the primary and secondary device. The two important aspects of the OSI model are: - It defines a layered

40、 structure for the communication software; - It provides each layer with an apparent direct link to the same layer at the other device. However, in real life, the only actual message path between the two devices is through the physical connection between the two layer 1 entities. The layer 2 entitie

41、s appear to communicate directly. In actual fact, a message passed from the first device to the second device takes the following path: - Layer 2 at the first device passes the message down to Layer 1; - Layer 1 transmits the message across the physical connection (for instance a wire) to layer 1 at

42、 the second device; - Layer 1 at the second device passes the message up to Layer 2 at the second device. Likewise, layer 7 entities appear to communicate directly. In actual fact, a message passed from the first device to the second device takes the following path: - Layer 7 at the first device pas

43、ses the message down to Layer 2; - Layer 2 at the first device passes the message down to Layer 1; - Layer 1 transmits the message across the physical connection (for instance a wire) to layer 1 at the second device; - Layer 1 at the second device passes the message up to Layer 2 at the second devic

44、e; - Layer 2 at the second device passes the message up to Layer 7 at the second device. 7 Application 7 Application1 Physical2DataLink1 Physical2DataLinkActual message pathApparent message pathETSI ETSI TS 125 460 V13.0.0 (2016-01)113GPP TS 25.460 version 13.0.0 Release 13Annex B (informative): Cha

45、nge History TSG # TSG Doc. CR Rev Subject/Comment New 06/2008 - - - Creation of Rel-8 version based on v7.1.0 8.0.0 40 RP-080309 0007 Correction of figure 6.4.1 8.0.0 43 RP-090085 0008 1 RET and TMA support in LTE 8.1.0 12/2009 - - - Creation of Rel-9 version based on v8.1.0 9.0.0 01/2011 - - - Crea

46、tion of Rel-10 version based on v9.0.0 10.0.0 03/2011 SP-100629 Clarification on the use of References (TS 21.801 CR#0030) 10.0.1 09/2012 Update to Rel-11 version (MCC) 11.0.0 09/2014 Update to Rel-12 version (MCC) 12.0.0 12/2015 Update to Rel-13 version (MCC) 13.0.0 ETSI ETSI TS 125 460 V13.0.0 (2016-01)123GPP TS 25.460 version 13.0.0 Release 13History Document history V13.0.0 January 2016 Publication