ETSI TS 126 201-2016 Digital cellular telecommunications system (Phase 2+) Universal Mobile Telecommunications System (UMTS) LTE Speech codec speech processing functions Adaptive M.pdf

1、 ETSI TS 1Digital cellular telecoUniversal Mobile TelSpeech codec sAdaptive Multi-Rate - F(3GPP TS 26.2TECHNICAL SPECIFICATION126 201 V13.0.0 (2016communications system (Phaelecommunications System (LTE; c speech processing functionWideband (AMR-WB) speecFrame structure .201 version 13.0.0 Release 1

2、316-01) hase 2+); (UMTS); ons; ech codec; 13) ETSI ETSI TS 126 201 V13.0.0 (2016-01)13GPP TS 26.201 version 13.0.0 Release 13Reference RTS/TSGS-0426201vd00 Keywords GSM,LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N

3、 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The c

4、ontent of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable D

5、ocument Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.

6、org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical,

7、including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standa

8、rds Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are

9、Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 126 201 V13.0.0 (2016-01)23GPP TS 26.201 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these ess

10、ential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updat

11、es are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web serve

12、r) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identitie

13、s or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not

14、“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct cita

15、tion. ETSI ETSI TS 126 201 V13.0.0 (2016-01)33GPP TS 26.201 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 5g32 References 5g33 Definitions and Abbreviations 5g33.1 Definitions 5g33.2 Abbreviations . 5g34 AMR-WB codec

16、Interface format 1 (AMR-WB IF1) . 6g34.1 AMR-WB Header and AMR-WB Auxiliary Information 6g34.1.1 Frame Type, Mode Indication, and Mode Request . 6g34.1.2 Frame Quality Indicator 7g34.1.3 Mapping to TX_TYPE and RX_TYPE 7g34.1.4 Codec CRC . 8g34.2 AMR-WB Core Frame . 8g34.2.1 AMR-WB Core Frame with sp

17、eech bits: Bit ordering 8g34.2.2 AMR-WB Core Frame with speech bits: Class division 8g34.2.3 AMR-WB Core Frame with comfort noise bits 9g34.3 Generic AMR-WB Frame Composition . 10g3Annex A (normative): AMR-WB Interface Format 2 (with octet alignment) 12g3Annex B (normative): Tables for AMR-WB Core F

18、rame bit ordering 14g3Annex C (informative): Change history . 23g3History 24g3ETSI ETSI TS 126 201 V13.0.0 (2016-01)43GPP TS 26.201 version 13.0.0 Release 13Foreword This Technical Specification (TS) has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present docum

19、ent are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where:

20、x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incr

21、emented when editorial only changes have been incorporated in the document. ETSI ETSI TS 126 201 V13.0.0 (2016-01)53GPP TS 26.201 version 13.0.0 Release 131 Scope The present document describes a generic frame format for the Adaptive Multi-Rate Wideband (AMR-WB) speech codec. This format shall be us

22、ed as a common reference point when interfacing speech frames between different elements of the 3G system and between different systems. Appropriate mappings to and from this generic frame format will be used within and between each system element. Annex A describes a second frame format which shall

23、 be used when octet alignment of AMR-WB frames is required. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number,

24、 etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. 1 3GPP TS 26.190: “AMR Wideband Speech Codec; Speech Transcoding Functions“. 2 3GPP TS 26.193: “AMR Wideband Speech Codec; Source Controlled Rate Operation“.

25、 3 3GPP TS 26.192: “AMR Wideband Speech Codec; Comfort Noise Aspects“. 3 Definitions and Abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: AMR-WB mode: one of the nine AMR-WB codec bit-rates denoted also with indices 0 to 8 where 0 map

26、s to the 6.60 kbit/s mode and 8 maps to the 23.85 kbit/s mode. AMR-WB codec mode: same as AMR-WB mode. RX_TYPE: classification of the received frame as defined in 2. TX_TYPE: classification of the transmitted frame as defined in 2. 3.2 Abbreviations For the purposes of the present document, the foll

27、owing abbreviations apply: CRC Cyclic Redundancy Check FQI Frame Quality Indicator GSM Global System for Mobile communication LSB Least Significant Bit MSB Most Significant BitRX Receive SCR Source Controlled Rate operation SID Silence Descriptor (Comfort Noise Frame) TX Transmit ETSI ETSI TS 126 20

28、1 V13.0.0 (2016-01)63GPP TS 26.201 version 13.0.0 Release 134 AMR-WB codec Interface format 1 (AMR-WB IF1) This clause describes the generic frame format for both the speech and comfort noise frames of the AMR-WB speech codec. This format is referred to as AMR-WB Interface Format 1 (AMR-WB IF1). Ann

29、ex A describes AMR-WB Interface Format 2 (AMR-WB IF2). Each AMR-WB codec mode follows the generic frame structure depicted in figure 1. The frame is divided into three parts: AMR-WB Header, AMR-WB Auxiliary Information, and AMR-WB Core Frame. The AMR-WB Header part includes the Frame Type and the Fr

30、ame Quality Indicator fields. The AMR-WB auxiliary information part includes the Mode Indication, Mode Request, and Codec CRC fields. The AMR-WB Core Frame part consists of the speech parameter bits or, in case of a comfort noise frame, the comfort noise parameter bits. In case of a comfort noise fr

31、ame, the comfort noise parameters replace Class A bits of AMR-WB Core Frame while Class B and C bits are omitted. It is to be noted that unlike AMR, AMR-WB uses only two bit protection classes A and B. In no case bits are assigned to protection class C and, correspondingly, no RAB subflow needs to b

32、e allocated for such a class. The mentioning of class C is only done for the purpose of keeping uniformity of this specification with the corresponding specification for AMR. Frame Type (4 bits) Frame Quality Indicator (1 bit) Mode Indication (4 bits) Mode Request (4 bits) Codec CRC (8 bits) Class A

33、 bits Class B bits Class C bits Figure 1. Generic AMR-WB frame structure 4.1 AMR-WB Header and AMR-WB Auxiliary Information This subclause describes the AMR-WB Header of figure 1. 4.1.1 Frame Type, Mode Indication, and Mode Request Table 1a defines the 4-bit Frame Type field. Frame Type can indicate

34、 the use of one of the nine AMR-WB codec modes, comfort noise frame, lost speech frame, or an empty frame. In addition, four Frame Type Indices are reserved for future use. The same table is reused for the Mode Indication and Mode Request fields which are 4-bit fields each and are defined only in th

35、e range 08 to specify one of the nine AMR-WB codec modes. AMR-WB Header AMR-WB Auxiliary Information (for Tandem Free Operation, Mode Adaptation, and Error Detection) AMR-WB Core Frame (speech or comfort noise data) ETSI ETSI TS 126 201 V13.0.0 (2016-01)73GPP TS 26.201 version 13.0.0 Release 13Table

36、 1a: Interpretation of Frame Type, Mode Indication and Mode Request fields. Frame Type Index Mode Indication Mode Request Frame content (AMR-WB mode, comfort noise, or other) 0 0 0 AMR-WB 6.60 kbit/s 1 1 1 AMR-WB 8.85 kbit/s 2 2 2 AMR-WB 12.65 kbit/s 3 3 3 AMR-WB 14.25 kbit/s 4 4 4 AMR-WB 15.85 kbit

37、/s 5 5 5 AMR-WB 18.25 kbit/s 6 6 6 AMR-WB 19.85 kbit/s 7 7 7 AMR-WB 23.05 kbit/s 8 8 8 AMR-WB 23.85 kbit/s 9 - - AMR-WB SID (Comfort Noise Frame) 10-13 - - For future use 14 - speech lost15 - - No Data (No transmission/No reception) - 4.1.2 Frame Quality Indicator The content of the Frame Quality In

38、dicator field is defined in Table 1b. The field length is one bit. The Frame Quality Indicator indicates whether the data in the frame contains errors. Table 1b: Definition of Frame Quality Indicator Frame Quality Indicator (FQI) Quality of data 0 Bad frame or Corrupted frame (bits may be used to as

39、sist error concealment) 1 Good frame 4.1.3 Mapping to TX_TYPE and RX_TYPE Table 1c shows how the AMR-WB Header data (FQI and Frame Type) maps to the TX_TYPE and RX_TYPE frames defined in 2. Table 1c: Mapping of Frame Quality Indicator and Frame Type to TX_TYPE and RX_TYPE 2, respectively Frame Quali

40、ty Indicator Frame Type Index TX_TYPE or RX_TYPE Comment 1 0-8 SPEECH_GOOD The specific Frame Type Index depends on the bit-rate being used. 0 0-8 SPEECH_BAD The specific Frame Type Index depends on the bit-rate being used. The corrupted data may be used to assist error concealment. 0 14 SPEECH_LOST

41、 No useful information. An erased or stolen frame with no data usable to assist error concealment. 1 9 9 SID_FIRST or SID_UPDATE SID_FIRST and SID_UPDATE are differentiated using one Class A bit: STI. 0 9 SID_BAD 1 15 NO_DATA Typically a non-transmitted frame. ETSI ETSI TS 126 201 V13.0.0 (2016-01)8

42、3GPP TS 26.201 version 13.0.0 Release 134.1.4 Codec CRC Generic AMR-WB codec frames with Frame Type 09 are associated with an 8-bit CRC for error-detection purposes. The Codec CRC field of AMR-WB Auxiliary Information in figure 1 contains the value of this CRC. These eight parity bits are generated

43、by the cyclic generator polynomial: - G(x)=D8+ D6+ D5+ D4+ 1 which is computed over all Class A bits of AMR-WB Core Frame. Class A bits for Frame Types 08 are defined in subclause 4.2.2 (for speech bits) and for Frame Type 9 in subclause 4.2.3 (for comfort noise bits). When Frame Type Index of table

44、 1a is 14 or 15, the CRC field is not included in the Generic AMR-WB frame. 4.2 AMR-WB Core Frame This subclause contains the description of AMR-WB Core Frame of figure 1. The descriptions for AMR-WB Core Frame with speech bits and with comfort noise bit are given separately. 4.2.1 AMR-WB Core Frame

45、 with speech bits: Bit ordering This subclause describes how AMR-WB Core Frame carries the coded speech data. The bits produced by the speech encoder are denoted as s(1),s(2),.,s(K), where K refers to the number of bits produced by the speech encoder as shown in table 2. The notation s(i) follows th

46、at of 1. The speech encoder output bits are ordered according to their subjective importance. This bit ordering can be utilized for error protection purposes when the speech data is, for example, carried over a radio interface. Tables B.1 to B.9 in Annex B define the AMR-WB IF1 bit ordering for all

47、the nine AMR-WB codec modes. In these tables the speech bits are numbered in the order they are produced by the corresponding speech encoder as described in the relevant tables of 3GPP TS 26.190 1. The reordered bits are denoted below, in the order of decreasing importance, as d(0),d(1),.,d(K-1). Th

48、e ordering algorithm is described in pseudo code as: - for j = 0 to K-1 - d(j) := s(tablem(j)+1); where tablem(j) refers to the relevant table in Annex B depending on the AMR-WB mode m=08. The Annex B tables should be read line by line from left to right. The first element of the table has the index

49、 0. 4.2.2 AMR-WB Core Frame with speech bits: Class division The reordered bits are further divided into three indicative classes according to their subjective importance. The three different importance classes can then be subject to different error protection in the network. The importance classes are Class A, Class B, and Class C. Class A contains the bits most sensitive to errors and any error in these bits typically results in a corrupted speech frame which should not be decoded without applying appropriate error concealment. This class is p