ETSI TS 132 111-2-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) LTE Telecommunication management Fault Manageme.pdf

1、 ETSI TS 132 111-2 V15.0.0 (2018-07) Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); LTE; Telecommunication management; Fault Management; Part 2: Alarm Integration Reference Point (IRP): Information Service (IS) (3GPP TS 32.111-2 versio

2、n 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)13GPP TS 32.111-2 version 15.0.0 Release 15Reference RTS/TSGS-0532111-2vf00 Keywords GSM,LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Si

3、ret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print.

4、The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Porta

5、ble Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal

6、.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic

7、or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All righ

8、ts reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Member

9、s. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)23GPP TS 32.111-2 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declare

10、d to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is

11、 available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETS

12、I SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any

13、 which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Forewor

14、d This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corres

15、ponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “canno

16、t“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)33GPP TS 32.111-2 version 15.0.0 Rel

17、ease 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 7g3Introduction 7g31 Scope 9g32 References 9g33 Definitions and abbreviations . 10g33.1 Definitions 10g33.2 Abbreviations . 10g34 Basic aspects 11g34.1 Void 11g34.2 System Context 11g35 Information Ob

18、ject Classes 12g35.1 Imported information entities and local labels . 12g35.2 Class diagram . 12g35.2.0 Introduction. 12g35.2.1 Attributes and relationships 12g35.2.2 Inheritance 13g35.3 Information Object Class Definitions . 13g35.3.1 AlarmInformation 13g35.3.1.1 Definition 13g35.3.1.2 Attribute 14

19、g35.3.1.3 State diagram. 14g35.3.2 AlarmList . 16g35.3.2.1 Definition 16g35.3.2.2 Attribute 16g35.3.3 AlarmIRP . 17g35.3.3.1 Definition 17g35.3.3.2 Attribute 17g35.3.3.3 Notification Table . 17g35.3.4 Comment . 17g35.3.4.1 Definition 17g35.3.4.2 Attribute 17g35.3.5 CorrelatedNotification 17g35.3.5.1

20、 Definition 17g35.3.5.2 Attribute 18g35.3.6 MonitoredEntity 18g35.3.6.1 Definition 18g35.3.6.2 Attribute 18g35.4 Information relationships definition . 19g35.4.1 relation-AlarmIRP-AlarmList (M) 19g35.4.1.1 Definition 19g35.4.1.2 Role . 19g35.4.1.3 Constraint 19g35.4.2 relation-AlarmList-AlarmInforma

21、tion (M) . 19g35.4.2.1 Definition 19g35.4.2.2 Role . 19g35.4.2.3 Constraint 19g35.4.3 relation-AlarmInformation-Comment (M) . 19g35.4.3.1 Definition 19g35.4.3.2 Role . 20g35.4.3.3 Constraint 20g3ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)43GPP TS 32.111-2 version 15.0.0 Release 155.4.4 relation-AlarmIn

22、formation-CorrelatedNotification (M) . 20g35.4.4.1 Definition 20g35.4.4.2 Role . 20g35.4.4.3 Constraint 20g35.4.5 relation-AlarmedObject-AlarmInformation (M) . 20g35.4.5.1 Definition 20g35.4.5.2 Role . 20g35.4.5.3 Constraint 20g35.4.6 relation-backUpObject-AlarmInformation (O) . 21g35.4.6.1 Definiti

23、on 21g35.4.6.2 Role . 21g35.4.6.3 Constraint 21g35.5 Information attribute definition 22g35.5.1 Definition and legal values . 22g35.5.2 Constraints 25g36 Interface Definition 26g36.1 Class diagram . 26g36.2 Generic rules 27g36.3 Interface AlarmIRPOperations_1 (M) 28g36.3.1 acknowledgeAlarms (M) 28g3

24、6.3.1.1 Definition 28g36.3.1.2 Input Parameters . 28g36.3.1.3 Output Parameters. 29g36.3.1.4 Pre-condition . 29g36.3.1.5 Post-condition . 29g36.3.1.6 Exceptions . 30g36.3.2 getAlarmList (M) 30g36.3.2.1 Definition 30g36.3.2.2 Input Parameters . 31g36.3.2.3 Output Parameters. 32g36.3.2.4 Pre-condition

25、 . 35g36.3.2.5 Post-condition . 35g36.3.2.6 Exceptions . 35g36.4 Interface AlarmIRPOperation_2 (O) 35g36.4.1 getAlarmCount (M) 35g36.4.1.1 Definition 35g36.4.1.2 Input Parameters . 36g36.4.1.3 Output Parameters. 36g36.4.1.4 Pre-condition . 37g36.4.1.5 Post-condition . 37g36.4.1.6 Exceptions . 37g36.

26、5 Interface AlarmIRPOperation_3 (O) 37g36.5.1 unacknowledgeAlarms (M) 37g36.5.1.1 Definition 37g36.5.1.2 Input Parameters . 37g36.5.1.3 Output Parameters. 38g36.5.1.4 Pre-condition . 38g36.5.1.5 Post-condition . 38g36.5.1.6 Exceptions . 39g36.6 Interface AlarmIRPOperation_4 (O) 39g36.6.1 setComment

27、(M) . 39g36.6.1.1 Definition 39g36.6.1.2 Input Parameters . 39g36.6.1.3 Output Parameter 39g36.6.1.4 Pre-condition . 40g36.6.1.5 Post-condition . 40g36.6.1.6 Exceptions . 40g36.7 Interface AlarmIRPOperation_5 (O) 40g36.7.1 clearAlarms (M) 40g36.7.1.1 Definition 40g36.7.1.2 Input Parameter . 41g3ETSI

28、 ETSI TS 132 111-2 V15.0.0 (2018-07)53GPP TS 32.111-2 version 15.0.0 Release 156.7.1.3 Output Parameter 41g36.7.1.4 Pre-condition . 41g36.7.1.5 Post-condition . 41g36.7.1.6 Exceptions . 42g36.8 Notification AlarmIRPNotifications_1 (M) . 42g36.8.0 Introduction. 42g36.8.1 notifyNewAlarm (M) 42g36.8.1.

29、1 Definition 42g36.8.1.2 Input Parameters . 43g36.8.1.3 Input Parameters for notification related to security alarm . 44g36.8.1.4 Triggering Event . 44g36.8.1.4.1 From-state 44g36.8.1.4.2 To-state 45g36.8.2 notifyAckStateChanged (M) . 45g36.8.2.1 Definition 45g36.8.2.2 Input Parameters . 46g36.8.2.3

30、 Triggering Event . 46g36.8.2.3.1 From-state 46g36.8.2.3.2 To-state 46g36.8.3 notifyClearedAlarm (M) . 47g36.8.3.1 Definition 47g36.8.3.2 Input Parameters . 47g36.8.3.3 Triggering Event . 47g36.8.3.3.1 From-state 47g36.8.3.3.2 To-state 48g36.8.4 notifyAlarmListRebuilt (M) 48g36.8.4.1 Definition 48g3

31、6.8.4.2 Input Parameters . 48g36.8.4.3 Triggering Event . 50g36.8.4.3.1 From-state 50g36.8.4.3.2 To-state 50g36.9 Notification AlarmIRPNotification_2 (O) 50g36.9.1 notifyChangedAlarm (M) . 50g36.9.1.1 Definition 50g36.9.1.2 Input Parameters . 51g36.9.1.3 Triggering Event . 51g36.9.1.3.1 From-state 5

32、1g36.9.1.3.2 To-state 51g36.10 Notification AlarmIRPNotification_3 (O) 52g36.10.1 notifyComments (M) 52g36.10.1.1 Definition 52g36.10.1.2 Input Parameters . 52g36.10.1.3 Triggering Events 52g36.10.1.3.1 From-state 52g36.10.1.3.2 To-state 53g36.11 Notification AlarmIRPNotification_4 (O) 53g36.11.1 no

33、tifyPotentialFaultyAlarmList (M) . 53g36.11.1.1 Definition 53g36.11.1.2 Input Parameters . 54g36.11.1.3 Triggering Event . 54g36.11.1.3.1 From-state 54g36.11.1.3.2 To-state 54g36.12 Notification AlarmIRPNotification_5 (O) 55g36.12.1 notifyCorrelatedNotificationChanged (M) . 55g36.12.1.1 Definition 5

34、5g36.12.1.2 Input Parameters . 55g36.12.1.3 Triggering Events 55g36.12.1.3.1 From-state 55g36.12.1.3.2 To-state 56g36.13 Notification AlarmIRPNotification_6 (O) 56g36.13.1 notifyChangedAlarmGeneral (M) . 56g36.13.1.1 Definition 56g3ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)63GPP TS 32.111-2 version 15

35、.0.0 Release 156.13.1.2 Input Parameters . 57g36.13.1.3 Input Parameters for notification related to security alarm . 58g36.13.1.4 Triggering Event . 58g36.13.1.4.1 From-state 58g36.13.1.4.2 To-state 59g3Annex A (normative): Event Types 60g3Annex B (normative): Probable Causes . 61g3Annex C (informa

36、tive): Examples of using notifyChangedAlarm 70g3Annex D (informative): Examples of using correlatedNotification . 72g3Annex E (informative): AcknowledgeAlarms operation scenario 73g3Annex F (informative): Change history . 74g3History 75g3ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)73GPP TS 32.111-2 vers

37、ion 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the pre

38、sent document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under ch

39、ange control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introduction The present document is part of a TS-family covering

40、 the 3rdGeneration Partnership Project: Technical Specification Group Services and System Aspects; Telecommunication management; as identified below: 32.111-1 “Fault Management; Part 1: 3G fault management requirements“. 32.111-2 “Fault Management; Part 2: Alarm Integration Reference Point (IRP): In

41、formation Service (IS)“. 32.111-6 “Fault Management; Part 6: Alarm Integration Reference Point (IRP): Solution Set (SS) definitions. The present document is part of a set of TSs which describes the requirements and information model necessary for the Telecommunication Management (TM) of 3GPP systems

42、. The TM principles and TM architecture are specified in 3GPP TS 32.101 6 and 3GPP TS 32.102 7. A 3GPP system is composed of a multitude of Network Elements (NE) of various types and, typically, different vendors inter-operate in a co-ordinated manner in order to satisfy the network users communicat

43、ion requirements. The occurrence of failures in a NE may cause a deterioration of this NEs function and/or service quality and will, in severe cases, lead to the complete unavailability of the NE. In order to minimize the effects of such failures on the Quality of Service (QoS) as perceived by the n

44、etwork users it is necessary to: - detect failures in the network as soon as they occur and alert the operating personnel as fast as possible; isolate the failures (autonomously or through operator intervention), i.e. switch off faulty units and, if applicable, limit the effect of the failure as muc

45、h as possible by reconfiguration of the faulty NE/adjacent NEs; - if necessary, determine the cause of the failure using diagnosis and test routines; and, - repair/eliminate failures in due time through the application of maintenance procedures. This aspect of the management environment is termed “F

46、ault Management“ (FM). The purpose of FM is to detect failures as soon as they occur and to limit their effects on the network QoS as far as possible. The latter is achieved by bringing additional/redundant equipment into operation, reconfiguring existing equipment/NEs, or by repairing/eliminating t

47、he cause of the failure. Fault Management (FM) encompasses all of the above functionalities except commissioning/decommissioning of NEs and potential operator triggered reconfiguration (these are a matter of Configuration Management). ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)83GPP TS 32.111-2 version

48、 15.0.0 Release 15FM also includes associated features in the Operations System (OS), such as the administration of alarm list, the presentation of operational state information of physical and logical devices/resources/functions, and the provision and analysis of the alarm and state history of the

49、network. ETSI ETSI TS 132 111-2 V15.0.0 (2018-07)93GPP TS 32.111-2 version 15.0.0 Release 151 Scope The present document defines the Alarm Integration Reference Point (IRP) Information Service (IS), which addresses the alarm surveillance aspects of Fault Management (FM), applied to the Itf-N. The purpose of the AlarmIRP is to define an interface through which a “system“ (typically a Network Element Manager or a Network Element) can communicate alarm information for its managed objects to one or several Manager Systems (typically Network Management Systems). The Alarm IRP