ETSI TS 144 013-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Performance requirements on the mobile radio interface (V15 0 0 3GPP TS 44 013 version 15 0 0 Relea.pdf

1、 ETSI TS 144 013 V15.0.0 (2018-07) Digital cellular telecommunications system (Phase 2+) (GSM); Performance requirements on the mobile radio interface (3GPP TS 44.013 version 15.0.0 Release 15) TECHNICAL SPECIFICATION GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI TS 144 013 V15.0.0 (2018-07)13GP

2、P TS 44.013 version 15.0.0 Release 15Reference RTS/TSGC-0144013vf00 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grass

3、e (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified with

4、out the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of t

5、he present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your c

6、omment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI

7、. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the be

8、nefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 144 01

9、3 V15.0.0 (2018-07)23GPP TS 44.013 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI memb

10、ers and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi

11、.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the

12、 present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark

13、 and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). T

14、he present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found un

15、der http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expre

16、ssion of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 144 013 V15.0.0 (2018-07)33GPP TS 44.013 version 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope

17、 5g32 References 5g33 Abbreviations and definitions 5g33.1 Abbreviations . 5g33.2 Definitions 6g34 Default conditions 6g35 Requirements 6g35.1 General requirements . 6g35.1.1 Response to layer 3 message. 6g35.1.2 Response to an erroneous layer 3 message . 6g35.2 Layer 3 Radio Resource signalling . 6

18、g35.2.0 Paging . 6g35.2.1 Paging and cell reselection after channel release 7g35.2.2 Paging commands and immediate assignment rejection (Timer T3122) 7g35.2.3 Immediate assignment (Timer T3101) 7g35.2.4 Channel assignment 7g35.2.5 Channel mode modify . 7g35.2.6 Handover access . 7g35.2.6.1 Finely, p

19、seudo and pre synchronized cases . 7g35.2.6.2 Non synchronized case 8g35.2.7 Encryption. 8g35.2.8 Classmark change . 8g35.2.9 Classmark interrogation 9g35.2.10 Release (Timer T3110) . 9g35.2.11 Early sending of the CLASSMARK CHANGE message . 9g35.3 Layer 3 Mobility Management signalling 9g35.3.1 Per

20、iodic location updating timer . 9g35.3.2 Identification . 9g35.3.3 Authentication . 9g35.3.4 T3240 expiry . 9g35.3.5 TMSI reallocation . 9g35.3.6 IMSI detach 9g35.3.7 Location updating with random access failure 10g35.3.8 Follow on call . 10g35.4 Layer 3 Call Control signalling 10g35.4.1 Time to sen

21、d SETUP message 10g35.4.2 Response times to CC messages . 10g35.4.3 User alerting 11g35.4.4 Call establishment . 11g35.4.5 Call reestablishment 11g35.4.6 In call modification . 11g35.4.7 DTMF . 11g35.5 Supplementary service signalling . 11g35.5.1 Advice of Charge Charging (AoCC) 11g35.6 Short Messag

22、e Services Point-to-Point 11g35.6.1 CP-DATA . 12g35.6.2 RP-DATA . 12g3Annex A (informative): Change History 13g3History 14g3ETSI ETSI TS 144 013 V15.0.0 (2018-07)43GPP TS 44.013 version 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project

23、(3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version

24、 number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections

25、, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 144 013 V15.0.0 (2018-07)53GPP TS 44.013 version 15.0.0 Release 151 Scope The present document specifies measurable performance requirements for signalling aspects of Mob

26、ile Stations (MS)s. To allow implementation flexibility it has been chosen to specify requirements on the whole Mobile Station rather than to specify requirements on each “OSI layer“. As a consequence the performance requirements do not fit conveniently in specifications such as 3GPP TS 24.008 4 and

27、 3GPP TS 44.018 4a (layer 3 only) or 3GPP TS 44.006 3 (layer 2 only). The main aim of the present document is to provide the justification for testing of requirements that are not included in other GSM specifications. Where specific requirements are included in other GSM specifications they are not

28、duplicated here. MSs have to perform a wide variety of functions. As a consequence most performance measurements have to be made under a set of defined conditions: where necessary, these are included in the present document. Where necessary certain assumptions are made about the interaction times be

29、tween the mobile equipment and the SIM. If the (test) SIM does not respond within the assumed time then appropriate allowances shall be made. Additionally, it is intended that the present document should contain sufficient requirements to enable some undefined network timers in 3GPP TS 24.008 4 and

30、3GPP TS 44.018 4a to be calculated. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific

31、. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release

32、 as the present document. 1 Void. 1a 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 3GPP TS 43.022: “Functions related to Mobile Station (MS) in idle mode and group receive mode“. 3 3GPP TS 44.006: “Mobile Station - Base Station System (MS - BSS) interface; Data Link (DL) layer specificatio

33、n“. 4 3GPP TS 24.008: “Mobile radio interface; Layer 3 specification“. 4a 3GPP TS 44.018: “Mobile radio interface layer 3 specification; Radio Resource Control Protocol“. 5 3GPP TS 24.086: “Advice of Charge (AoC) supplementary services; Stage 3“. 6 3GPP TS 45.002: Multiplexing and multiple access on

34、 the radio path“. 7 3GPP TS 45.008: “Radio subsystem link control“. 3 Abbreviations and definitions 3.1 Abbreviations For the purposes of the present document, the abbreviations given in 3GPP TR 21.905 1a apply. ETSI ETSI TS 144 013 V15.0.0 (2018-07)63GPP TS 44.013 version 15.0.0 Release 153.2 Defin

35、itions For the purposes of the present document, the following definition applies: ready to transmit: in the present document the phrase “ready to transmit the message before time x“ is defined to mean that the MS shall transmit part of that message no later than the first burst of the first TCH or

36、control channel block that occurs after time x. 4 Default conditions Unless otherwise stated, throughout the present document the following conditions are associated with the requirements: - ideal radio link with an insignificant bit error rate; - no other signalling is in progress on the main DCCH;

37、 - messages sent by the network are correctly formed; - the only established data link (or the only data link to be established) is on SAPI 0; - any Starting Time IE that is included in a message sent by the network does not require the action to be delayed; - cells are not barred and all access cla

38、sses are allowed; - the layer 2 performance of the network shall satisfy the “System Performance Requirements“ of subclause 5.9 of 3GPP TS 44.006 3; - messages sent by the network may contain any set of optional IEs, and any permitted set of conditional IEs; - the mobile has a valid SIM inserted, is

39、 powered on, and the SIMs update status is “updated“; and - on the CCCH, the Page Mode IE is not set to “paging reorganization“ or “same as before“. 5 Requirements 5.1 General requirements 5.1.1 Response to layer 3 message The requirements of subclause 5.1.1 apply if there are no specific requiremen

40、ts for a layer 3 message in other parts of clause 5. If the last timeslot of the message block containing a network command occurs at time T, then the MS shall be ready to transmit the response before time T + 500 ms. 5.1.2 Response to an erroneous layer 3 message If the last timeslot of the message

41、 block containing an erroneous RR, MM or CC message occurs at time T and if 3GPP TS 24.008 4 and 3GPP TS 44.018 4a requires a status message to be returned to the network then the MS shall be ready to transmit the RR-STATUS or MM-STATUS or STATUS message before T + 500 ms. 5.2 Layer 3 Radio Resource

42、 signalling 5.2.0 Paging If access to the network is allowed and the MS has been camped on a suitable cell for at least 2 s and if the last timeslot of the message block containing a PAGING REQUEST message addressing the MS occurs at time T, then the MS shall be ready to transmit the CHANNEL REQUEST

43、 message before T + 0,7 s. ETSI ETSI TS 144 013 V15.0.0 (2018-07)73GPP TS 44.013 version 15.0.0 Release 155.2.1 Paging and cell reselection after channel release If the last timeslot of the message block containing a CHANNEL RELEASE message occurs at time T the MS shall respond to PAGING REQUEST mes

44、sages sent later than T + 1,0 s. 5.2.2 Paging commands and immediate assignment rejection (Timer T3122) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT REJECT message is sent at time T and contains a Wait Indication of W seconds then the MS shall at least respond to PAGI

45、NG REQUEST messages sent later than T + (W + 1) s. 5.2.3 Immediate assignment (Timer T3101) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT (or IMMEDIATE ASSIGNMENT EXTENDED) message is transmitted at time T then, the MS shall be ready to transmit the SABM frame with its

46、 information field before T + 25 ms. This requirement shall apply for assignment to TCH/F, TCH/H and SDCCH. 5.2.4 Channel assignment If the last timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T, then the MS shall be ready to transmit the ASSIGNMENT COMPLETE message bef

47、ore T + 600 ms. If the last timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the A

48、SSIGNMENT FAILURE message on the old channel before T + 2 s. If the last timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS shall not attempt to establish a layer 2 link on the new channel, then the MS shall be ready to tra

49、nsmit any ASSIGNMENT FAILURE message on the old channel before T + 500 ms. 5.2.5 Channel mode modify If the last timeslot of the message block containing a CHANNEL MODE MODIFY message occurs at time T, then the MS shall be ready to transmit the CHANNEL MODE MODIFY ACKNOWLEDGE message before T + 300 ms. In the case that the call is a voice group or voice broadcast call the MS shall be ready to transmit the CHANNEL MODE ACKNOWLEDGE message before T + 50 ms. 5.2.6 Handover access 5.2.6.1 Finely, pseudo and pre synchronized cases If the last ti