ETSI TS 146 022-2016 Digital cellular telecommunications system (Phase 2+) Half rate speech Comfort noise aspects for the half rate speech traffic channels (V13 0 0 3GPP TS 46 022 .pdf

1、 ETSI TS 1Digital cellular telecoHComfort noise aspects f(3GPP TS 46.0TECHNICAL SPECIFICATION146 022 V13.0.0 (2016communications system (PhaHalf rate speech; s for the half rate speech traffi.022 version 13.0.0 Release 13GLOBAL SYSTEMOBILE COMMUN16-01) hase 2+); ffic channels 13) TEM FOR ICATIONSRET

2、SI ETSI TS 146 022 V13.0.0 (2016-01)13GPP TS 46.022 version 13.0.0 Release 13Reference RTS/TSGS-0446022vd00 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucrat

3、if enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the pre

4、sent document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network d

5、rive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the presen

6、t document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized

7、 by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTEST

8、STM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.

9、ETSI ETSI TS 146 022 V13.0.0 (2016-01)23GPP TS 46.022 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI membe

10、rs and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.

11、org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the

12、present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being

13、 references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “wi

14、ll not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 146 022 V13.0.0 (2016-01)33GPP TS 46.0

15、22 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 5g32 References 5g33 Definitions, symbols and abbreviations . 5g33.1 Definitions 5g33.2 Symbols 6g33.3 Abbreviations . 6g34 General . 6g35 Functions on the transmit (TX

16、) side . 7g35.1 Background acoustic noise evaluation . 7g35.2 Modification of the speech encoding algorithm during SID frame generation 8g35.3 SID-frame encoding . 9g36 Functions on the receive (RX) side 10g36.1 Averaging of the GS parameters 10g36.2 Comfort noise generation and updating 11g37 Compu

17、tational details . 11g3Annex A (informative): Change Request History 12g3History 13g3ETSI ETSI TS 146 022 V13.0.0 (2016-01)43GPP TS 46.022 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The present document gives the

18、detailed requirements for the correct operation of the background acoustic noise evaluation, noise parameter encoding/decoding and comfort noise generation within the digital cellular telecommunications system. The present document is part of a series covering the half rate speech traffic channels a

19、s described below: GSM 06.02 “Digital cellular telecommunications system (Phase 2+); Half rate speech; Half rate speech processing functions“. GSM 06.06 “Digital cellular telecommunications system (Phase 2+); Half rate speech; ANSI-C code for the GSM half rate speech codec“. GSM 06.07 “Digital cellu

20、lar telecommunications system (Phase 2+); Half rate speech; Test sequences for the GSM half rate speech codec“. GSM 06.20 “Digital cellular telecommunications system (Phase 2+); Half rate speech; Half rate speech transcoding“. GSM 06.21 “Digital cellular telecommunications system (Phase 2+); Half ra

21、te speech; Substitution and muting of lost frames for half rate speech traffic channels“. GSM 06.22 “Digital cellular telecommunications system (Phase 2+); Half rate speech; Comfort noise aspects for half rate speech traffic channels“. GSM 06.41 “Digital cellular telecommunications system (Phase 2+)

22、; Half rate speech; Discontinuous Transmission (DTX) for half rate speech traffic channels“. GSM 06.42 “Digital cellular telecommunications system (Phase 2+); Half rate speech; Voice Activity Detector (VAD) for half rate speech traffic channels“. The contents of the present document are subject to c

23、ontinuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1

24、 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editori

25、al only changes have been incorporated in the document. ETSI ETSI TS 146 022 V13.0.0 (2016-01)53GPP TS 46.022 version 13.0.0 Release 131 Scope The present document gives the detailed requirements for the correct operation of the background acoustic noise evaluation, noise parameter encoding/decoding

26、 and comfort noise generation in GSM Mobile Stations (MS)s and Base Station Systems (BSS)s during Discontinuous Transmission (DTX) on half rate speech traffic channels. The requirements described in the present document are mandatory for implementation in all GSM MSs capable of supporting the half r

27、ate speech traffic channel. The receiver requirements are mandatory for implementation in all GSM BSSs capable of supporting the half rate speech traffic channel, the transmitter requirements are only for those where downlink DTX will be used. 2 References The following documents contain provisions

28、which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, t

29、he latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 GSM 01.04: “Digital cellular telecommunication system (Phase 2+); Abbr

30、eviations and acronyms“. 2 GSM 06.20: “Digital cellular telecommunications system (Phase 2+); Half rate speech transcoding“. 3 GSM 06.41: “Digital cellular telecommunications system (Phase 2+); Half rate speech; Discontinuous Transmission (DTX) for half rate speech traffic channels“. 4 GSM 06.42: “D

31、igital cellular telecommunications system (Phase 2+); “Half rate speech; Voice Activity Detector (VAD) for half rate speech traffic channels“. 5 GSM 06.06: “Digital cellular telecommunications system (Phase 2+); Half rate speech; ANSI-C code for the GSM half rate speech codec“. 3 Definitions, symbol

32、s and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply. frame: time interval of 20 ms corresponding to the time segmentation of the half rate speech transcoder, also used as a short term for a traffic frame. H(Z): combination of the sh

33、ort term (spectral) filter A(z) and the spectral weighting filter W(z). SID codeword: fixed bit pattern for labelling a traffic frame as a SID frame. SID field: bit positions of the SID codeword within a SID frame. SID frame: frame characterized by the SID (Silence Descriptor) codeword. It conveys i

34、nformation on the acoustic background noise. ETSI ETSI TS 146 022 V13.0.0 (2016-01)63GPP TS 46.022 version 13.0.0 Release 13SP flag: speech flag. speech frame: traffic frame that cannot be classified as a SID frame. VAD flag: Voice Activity Detector flag. W(Z): spectral weighting filter of the GSM h

35、alf rate speech codec. Other definitions of terms used in the present document can be found in GSM 06.20 2 and GSM 06.41 3. The overall operation of DTX is described in GSM 06.41 3. 3.2 Symbols For the purposes of the present document, the following symbols apply: GS Energy tweak parameter. R0 Frame

36、 energy value. R(i) Unquantised (normalized) autocorrelation sequence. rjOptimal reflection coefficient. b SUM ( x(n) ) = x(a) + x(a+1) + + x(b-1) + x(b); (Accumulation). n=a GSP0 codeword Vector quantization index, joint vector quantization of the parameters GS and P0. P0 Power contribution of the

37、first excitation vector as a fraction of the total excitation power at a subframe. 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: AFLAT Autocorrelation Fixed Point LAttice Technique (used in the GSM half rate speech codec for the vector quantization of

38、 the LPC coefficients) BSS Base Station System DTX Discontinuous Transmission ETS European Telecommunication Standard GSM Global System for Mobile communications MS Mobile StationSID SIlence Descriptor RX Receive TX TransmitVAD Voice Activity Detector VQ Vector QuantizationFor abbreviations not give

39、n in this subclause, see GSM 01.04 1. 4 General A problem when using DTX is that the background acoustic noise, which is transmitted together with the speech, would disappear when the radio transmission is switched off, resulting in a modulation of the background noise. Since the DTX switching can t

40、ake place rapidly, it has been found that this effect may be annoying for the listener, especially in a car environment with high background noise levels. In bad cases, the speech may be hardly intelligible. The present document specifies a solution to overcome this problem by generating synthetic n

41、oise similar to the transmit (TX) side background noise on the receive (RX) side. The comfort noise parameters are estimated on the TX side and transmitted to the RX side before the radio transmission is switched off and at a regular low rate afterwards. This allows the comfort noise to adapt to the

42、 changes of the noise on the TX side. ETSI ETSI TS 146 022 V13.0.0 (2016-01)73GPP TS 46.022 version 13.0.0 Release 135 Functions on the transmit (TX) side The comfort noise evaluation algorithm uses the following parameters of the GSM half rate speech encoder, defined in GSM 06.20 2: - the unquantiz

43、ed frame energy value R0; - the unquantized (normalized) autocorrelation sequence R(i) derived from the optimal reflection coefficients rj; - the quantized energy tweak parameter GS. These parameters give information on the level (R0 and GS) and the spectrum (R(i) of the background noise. Two of the

44、 evaluated comfort noise parameters (R0 and R(i) are encoded into a special frame, called a SIlence Descriptor (SID) frame, for transmission to the RX side. While the energy tweak parameter GS can be evaluated in the encoder and decoder in the same way as given in subclause 5.1, therefore no transmi

45、ssion of GS is necessary. The SID frame also serves to initiate the comfort noise generation on the RX side, as a SID frame is always sent at the end of a speech burst, i.e. before the radio transmission is terminated. The scheduling of SID or speech frames on the radio path is described in GSM 06.4

46、1 3. 5.1 Background acoustic noise evaluation The comfort noise parameters to be encoded into a SID frame are calculated over 8 consecutive frames marked with Voice Activated Detector (VAD) flag = “0“, as follows: The frame energy values shall be averaged according to the equation: 7 mean (R0j) = 1/

47、8 SUM R0j-n; n=0 where: R0j is the frame energy value of the current frame j (n=0); R0j-n is the frame energy of the previous frames (n=1,.,7); n is the averaging period index n=0,1,.,7; j is the frame index. The averaged value mean(R0j) is encoded using the same encoding table that is also used by

48、the GSM half rate speech codec for the encoding of the non-averaged R0 values in ordinary speech encoding mode. The (normalized) autocorrelation sequence R(i) shall be averaged according to the equation: 7 mean (Rj(i) = 1/8 SUM Rj-n(i) i = 0,1,2.,10; n=0 where: Rj(i) is the ith autocorrelation value

49、 of the current frame j (n=0); Rj-n(i) is the ith autocorrelation value of one of the previous frames (n=1,.,7); n is the averaging period index n=0,1.,7; j is the frame index. ETSI ETSI TS 146 022 V13.0.0 (2016-01)83GPP TS 46.022 version 13.0.0 Release 13The averaged values mean(Rj(i) are used as input parameters of the Autocorrelation Fixed Point LAttice Technique (AFLAT) recursion algorithm which calculates the Vector Quantization (VQ) indices of the reflection coefficients, see GSM 06.20 2. The SID frame containin