ETSI TS 186 014-2-2017 Core Network and Interoperability Testing (INT) Communication Diversion (CDIV) using IP Multimedia (IM) Core Network (CN) subsystem (3GPP Release 12) Part 2 .pdf

1、 ETSI TS 186 014-2 V4.1.1 (2017-12) Core Network and Interoperability Testing (INT); Communication Diversion (CDIV) using IP Multimedia (IM) Core Network (CN) subsystem; (3GPP Release 12); Part 2: Test Suite Structure and Test Purposes (TSS Essential, or potentially Essential, IPRs notified to ETSI

2、in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existe

3、nce of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI clai

4、ms no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations as

5、sociated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability Testing (INT). The present document is part 2 of a multi-part deliverable covering Communication Diversion (CDIV), as identified below: Part 1: “

6、Protocol Implementation Conformance Statement (PICS)“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification“. Modal verbs terminology In the present document “shall“, “

7、shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in di

8、rect citation. Introduction The Communications Diversion (CDIV) services enables the diverting user, to divert the communications addressed to diverting user to another destination. ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)51 Scope The present document specifies the Test Suite Structure and Test Purpo

9、ses (TSS Universal Mobile Telecommunications System (UMTS); LTE; Communication Diversion (CDIV) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol specification (3GPP TS 24.604 Release 12)“. 2 ETSI TS 186 014-1: “Core Network and Interoperability Testing (INT); Communication Diversion (C

10、DIV) using IP Multimedia (IM) Core Network (CN) subsystem; (3GPP Release 12); Part 1: Protocol Implementation Conformance Statement (PICS)“. 3 ISO/IEC 9646-1:1994: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 IE

11、TF RFC 7044: “An Extension to the Session Initiation Protocol (SIP) for Request History Information“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version

12、 applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are no

13、t necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)63 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definiti

14、ons given in ETSI TS 124 604 1 and the following apply: Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 3. Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 3. PICS pro forma: Refer to ISO/IEC 9646-1 3. Point of control and observation: Refer to ISO/IEC 9646-1 3. Protocol Implementation Co

15、nformance Statement (PICS): Refer to ISO/IEC 9646-1 3. System Under Test (SUT): Refer to ISO/IEC 9646-1 3. Test Purpose (TP): Refer to ISO/IEC 9646-1 3. 3.2 Symbols For the purposes of the present document, the following symbols apply: Gm Reference Point between a UE and a P-CSCF Mg Reference Point

16、between an MGCF and a CSCF Mw Reference Point between a CSCF and another CSCF Mx Reference Point between a CSCF/BGCF and IBCF 3.3 Abbreviations For the purposes of the present document, the abbreviations given in ETSI TS 124 604 1 and the following apply: ISC IP Multimedia Subsystem Service Control

17、NDUB Network Determined User Busy NNI Network - Network Interface TSS Test Suite Structure UDUB User Determined User Busy ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)74 Test Suite Structure (TSS) 4.0 Table of Test suite Structure Table 1: Test suite structure Netw ASdivertingUser/DivProcedures CDIV_N01_x

18、xx ASdivertingUser/NotOrigUser CDIV_N02_xxxASdivertingUser/NotTermUser CDIV_N03_xxxASdivertingUser/NotDivUser CDIV_N04_xxxASdiverted-to CDIV_N05_xxx User OrigUE CDIV_U01_xxxDiverted-toUE CDIV_U02_xxx ivertingUE CDIV_U03_xxxInteraction TIP CDIV_N06_xxx IR CDIV_N07_xxxOIR CDIV_N08_xxxACR-CB CDIV_N09_x

19、xxECT CDIV_N10_xxx 4.1 Configuration The scope of the present document is to test the signalling and procedural aspects of the stage 3 requirements as described in ETSI TS 124 604 1. The stage 3 description respects the requirements to several network entities and also to requirements regarding to e

20、nd devices. Therefore several interfaces (reference points) are addressed to satisfy the test of the different entities. Therefore, to test the appropriate entities, the configurations below are applicable: Testing of the Application Server: This entity is responsible to perform the service. Hence t

21、he ISC interface is the appropriate access point. Figure 1 points to this. Figure 1: Applicable interface to test AS functionalities If the ISC interface is not accessible it is also applicable to perform the test of the AS using any NNI (Mw, Mg, Mx) interface (consider figure 2). In case only the G

22、m interface is accessible this shall be used instead. In this case, be aware that the verification of several requirements is impeded. ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)8Figure 2: Applicable interfaces to test using the (generic) NNI interface Figure 3 illustrates the usage of any NNI interface

23、. Testing of User Equipment: There are several requirements regarding to the end devices. Therefore, a special configuration appears. Figure 3: Applicable configuration to test the User Equipment 5 Test Purposes (TP) 5.1 Introduction 5.1.1 TP naming convention TPs are numbered, starting at 001, with

24、in each group. Groups are organized according to the TSS. Additional references are added to identify the actual test suite and whether it applies to the network or the user (see figure 4). Identifier: _ = supplementary service: e.g. “CDIV“ = type of IUT: U User N Networkyyy service = group 2 digit

25、field representing group reference according to TSS = sequential number (001-999) Figure 4: TP identifier naming convention scheme ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)95.1.2 Test strategy As the base standard ETSI TS 124 604 1 contains no explicit requirements for testing, the TPs were generated

26、as a result of an analysis of the base standard and the PICS specification ETSI TS 186 014-1 2. 5.2 Signalling requirements 5.2.1 Actions at the AS of the diverting User 5.2.1.1 Diversion procedures TSS Netw/ASdivertingUser/DivProcedures TP CDIV_N01_001 Reference 1, 4.5.2.6.1 Selection expression PI

27、CS 4.5.1/2 AND PICS 4.7.1/2 Test purpose Served user has activated CFB, maximum number of diversion exceeded. Ensure that the 486 (Busy here) final response with a Warning header is sent to the original user if the served user has activated the CFB simulation service and the served user is busy and

28、if the maximum number of diversions is exceeded. SIP header values: INVITE: sip:SIP#n SIP/2.0 History-Info: ;index=1, Build additional entries with non significant uri values ;index=1.n.1 Warning: is present NOTE: For each redirection a history-entry is added the History-Info header and the relevan

29、t index is incremented according the rules described in clause 4.5.2.6.2.3 of 1. In short: each redirection is represented by a “.“ (dot) in the latest history-entry. Comments: SIP#1 AS SIP#n SIP#n+1 INVITE 1 barb4right barb4right INVITE 1 barb4left 486 Busy Here 486 (Busy here) barb4left barb4right

30、 ACK ACK barb4right ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)10TSS Netw/ASdivertingUser/DivProcedures TP CDIV_N01_002 Reference 1, 4.5.2.6.1 Selection expression PICS 4.5.1/2 AND PICS 4.7.1/3 Test purpose Served user has activated CFNR, maximum number of diversion exceeded. Ensure that the 480 (Tempor

31、arily unavailable) final response with a Warning header is sent to the original user if the served user does not answer the communication request and if the maximum number of diversions is exceeded. SIP header values: INVITE: sip:SIP#n SIP/2.0 History-Info: ;index=1, Build additional entries with n

32、on significant uri values ;index=1.n.1 Warning: is present NOTE: For each redirection a history-entry is added the History-Info header and the relevant index is incremented according the rules described in clause 4.5.2.6.2.3 of 1. In short: each redirection is represented by a “dot“ in the latest hi

33、story-entry. Comments: SIP#1 AS SIP#n SIP#n+1 INVITE barb4right barb4right INVITE 180 Ringing barb4left barb4left 180 Ringing No reply timer expires 480 (Temporarily unavailable) barb4left barb4right CANCEL ACK barb4right barb4left 200 OK CANCEL barb4left 487 Request Terminated barb4right ACK TSS Ne

34、tw/ASdivertingUser/DivProcedures TP CDIV_N01_003 Reference 1, 4.5.2.6.1 Selection expression PICS 4.5.1/2 AND PICS 4.7.1/1 Test purpose Served user has activated CFU, maximum number of diversion exceeded. Ensure that the 480 (Temporarily unavailable) final response with a Warning header is sent to t

35、he original user if the served user has activated the CFU simulation service and if the maximum number of diversions is exceeded. SIP header values: INVITE: sip:SIP#n SIP/2.0 History-Info: ;index=1, Build additional entries with non significant uri values ;index=1.n.1 Warning: is present NOTE: For

36、each redirection a history-entry is added the History-Info header and the relevant index is incremented according the rules described in clause 4.5.2.6.2.3 of 1. In short: each redirection is represented by a “dot“ in the latest history-entry. Comments: SIP#1 AS SIP#n SIP#n+1 INVITE barb4right 480 (

37、Temporarily unavailable) barb4left ACK barb4right ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)11TSS Netw/ASdivertingUser/DivProcedures TP CDIV_N01_004 Reference 1, 4.5.2.6.1 Selection expression PICS 4.5.1/2 AND PICS 4.7.1/4 OR PICS 4.7.1/5 Test purpose Served user has activated CD, maximum number of div

38、ersion exceeded. Ensure that the 480 (Temporarily unavailable) final response with a Warning header is sent to the original user if the served user has activated the CD simulation service and if the maximum number of diversions is exceeded. SIP header values: INVITE: sip:SIP#n SIP/2.0 History-Info:

39、 ;index=1, Build additional entries with non significant uri values ;index=1.n.1 Warning: is present NOTE: For each redirection a history-entry is added the History-Info header and the relevant index is incremented according the rules described in clause 4.5.2.6.2.3 of 1. In short: each redirection

40、is represented by a “dot“ in the latest history-entry. Comments: SIP#1 AS SIP#n SIP#n+1 INVITE barb4right barb4right INVITE 180 Ringing barb4left barb4left 180 Ringing barb4left barb4left 302 Moved Temporarily barb4right ACK 480 (Temporarily unavailable) barb4left ACK barb4right 5.2.1.2 Notification

41、 procedure of the originating terminating and diverting user 5.2.1.2.1 Originating user TSS Netw/ASdivertingUser/NotOrigUser TP CDIV_N02_001 Reference 1, 4.5.2.6.4 Selection expression PICS 4.5.1/2 AND PICS 4.7.3/3 AND (PICS 4.7.1/1 OR PICS 4.7.1/2 OR PICS 4.7.1/6 OR PICS 4.7.1/7) Test purpose Commu

42、nication forwarding using CFU or using CFB NDUB, CFNL or CFNRc with applying diversion condition; originating user is not notified. When Communication Diversion occurs and if the notification procedures of the originating user is supported then no 181 (Call Is Being Forwarded) response shall be sent

43、 towards the originating user if the served users subscription option is set to: Originating user receives notification that his communication has been diverted (forwarded or deflected) = no. Subscription options: Originating user receives notification that his communication has been diverted (forwa

44、rded or deflected) = no Comments: SIP#1 AS SIP#2 SIP#3 INVITE barb4right barb4right INVITE ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)12TSS Netw/ASdivertingUser/NotOrigUser TP CDIV_N02_002 Reference 1, 4.5.2.6.4 Selection expression PICS 4.5.1/2 AND PICS 4.7.3/3 AND PICS 4.7.3/4 AND PICS 4.7.3/5 AND (PI

45、CS 4.7.1/1 OR PICS1/2 OR PICS 4.7.1/6 OR PICS 4.7.1/7) Test purpose Communication forwarding using CFU or using CFB NDUB, CFNL or CFNRc with applying diversion condition; originating user is notified. When Communication Diversion occurs and if the notification procedures of the originating user is s

46、upported then a 181 (Call Is Being Forwarded) response shall be sent towards the originating user containing: a P-Asserted-Identity header with the URI of the served user and a History-Info header including a first entry with the hi-targeted-to-URI of the served, index = 1 and including a second ent

47、ry with the hi-targeted-to-URI of the diverted-to user, cause = CAU_VA and escaped Privacy header set to history, index = 1.1 and including the mp-param hi-target-param set to the index-val of this second hi-targeted-to-URI. Subscription options: Originating user receives notification that his commu

48、nication has been diverted (forwarded or deflected) = yes Served user allows the presentation of diverted to URI to originating user in diversion notification = yes Served user allows the presentation of his/her URI to originating user in diversion notification = yes SIP header values: 181 Call is B

49、eing Forwarded: P-Asserted-Identity: SIP#2 History-Info: ;index=1, ;index=1.1;mp=1.1 Comments: SIP#1 AS SIP#2 SIP#3 INVITE barb4right 181 Call is Being Forwarded barb4left barb4right INVITE ETSI ETSI TS 186 014-2 V4.1.1 (2017-12)13TSS Netw/ASdivertingUser/NotOrigUser TP CDIV_N02_003 Reference 1, 4.5.2.6.4 Selection expression PICS 4.5.1/2 AND PICS 4.7.3/3 AND (PICS 4.7.3/5 OR PICS 4.7.4/3) AND PICS 4.7.3/4 AND (PICS 4.7.1/1 OR PICS1/2 OR PICS 4.7.1/6 OR PICS 4.7.1/7) Te