FORD C-10-2003 VEHICLE AND BODY LAYOUT REFERENCE PLANES (Version 28).pdf

1、 FECDS C-10Engineering CAD & Drafting Standards Ford Proprietary and/or Confidential Information - Do not distribute to others w/o prior written authorization. Version 28 TOC Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20031231C101 Printed copies are uncontrolled.VEHICLE

2、 AND BODY LAYOUT REFERENCE PLANES 1 INTRODUCTION 1.1 Increasing emphasis on the coordinated worldwide products reinforces the need for common reference planes on both passenger cars and trucks throughout all Ford Product Engineering locations. Such reference planes will facilitate vehicle comparison

3、, design or derivative vehicles and the multi-use of major vehicle elements. These reference planes are in accordance with the SAE J1100 JUN93 SAE Recommended Practice. 2 DEFINITIONS 2.1.1 Inside Top of Frame a horizontal plane tangent to the frame side rail top flange inner surface. 2.1.2 Underside

4、 of Cab Floor a horizontal plane tangent to the lowest predominating surface on the underside surface of the cab floor at the centerline of driver (RHD or LHD) disregarding flanges and localized depressions. 2.1.3 Centerline of the Front Wheel a vertical plane at the intersection of the wheel axis a

5、nd the mid plane of the wheel at design position. 2.1.4 Front of Dash a vertical plane tangent to the foremost predominating surface of the passenger compartment at the centerline of driver (RHD or LHD) disregarding flanges and localized depressions. 2.2 RELOCATION OF FEATURES/SURFACES 2.2.1 In the

6、development of the vehicle, the feature/surface identified as the reference to establish the grid may need to be moved. In these circumstances, the zero reference planes already established must not be moved. The original surface/feature may therefore, cease to be coincident with the established gri

7、d line. 3 REQUIREMENTS 3.1 This standard applies to all new design passenger cars and trucks regardless of design office locations. Exception to use of the reference planes as shown in this standard may be made where an existing vehicle underbody structure using the previous reference plane system i

8、s carried over to a new body skin. Return to TOC ENGINEERING CAD & DRAFTING STANDARDS 3.2 REFERENCE PLANE SELECTION 3.2.1 When the initial concept vehicle is drawn onto the 100 grid (see Figure C10.1) features/surfaces to locate the vehicle will be as follows: NOTE: For some of the terms that are us

9、ed to describe the reference planes see DEFINITIONS for explanations. REFERENCE PLANE CARS LIGHT TRUCKS XPlane Front of Dash Front of Dash YPlane Center Line of Vehicle Center Line of Vehicle ZPlane Frame Vehicles Inside Top of Frame Frame Vehicles Inside Top of Frame Unitized Vehicles Top of Sill H

10、eel Line Unitized Vehicles Underside of Floor 3.2.2 The grid lines on which the features/surfaces are located are as follows: REFERENCE PLANES CARS LIGHT TRUCKS XPlane 2000 Line 2000 Line YPlane 0 Line 0 Line ZPlane 500 Line 700 Line 3.3 REQUIREMENTS 3.3.1 The initial concept vehicle, body and seati

11、ng layouts should be drawn with the specified vehicle reference planes located on the designated grid lines. 3.3.2 Figure C10.1 through Figure C10.3 show the passenger car in relation to the reference planes. Figure C10.4 and Figure C10.5 show light trucks. Original Issue: 19960419 Copyright, Ford M

12、otor Company. Latest Re-issue: 20031231C102 Printed copies are uncontrolled.Return to TOC ENGINEERING CAD & DRAFTING STANDARDS Figure C10.1 Figure C10.2 Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20031231C103 Printed copies are uncontrolled.Return to TOC ENGINEERING CAD

13、 & DRAFTING STANDARDS Figure C10.3 LIGHT TRUCK FRAME VEHICLE Figure C10.4 Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20031231C104 Printed copies are uncontrolled.Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20031231C105Return to TOC ENGINEERING CAD & DRAFTING STANDARDS Figure C10.5 4 SPECIFICATIONS (Reserved) 5 ADDENDUM (Reserved) Printed copies are uncontrolled.