FORD ESA-M12G80-A2-2012 LAMINATE CERAMIC SHEET ALUMINUM FOIL HEAT SHIELD TO BE USED WITH FORD WSS-M99P1111-A 《层压陶瓷板铝箔防热罩 与福特WSS-M99P1111-A 一起使用》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2000 09 11 Revised Updated A. Cockman 1991 03 25 NC00-E 10079774- 005 (RD) L. Mastrofrancesco Released Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. LAMINATE, CER

2、AMIC SHEET, ALUMINUM FOIL, ESA-M12G80-A2 HEAT SHIELD 1. SCOPE The material defined by this specification is a wet formed ceramic sheet with aluminum foil laminated to one or both sides as required by the end use. 2. APPLICATION This spec ification was released originally for material used as a heat

3、shield for chassis components such as power steering gear and powertrain isolation hydromount. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the Companys

4、 Quality System Requirements. 3.2 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwis

5、e specified. 3.3 CONSTRUCTION 3.3.1 Ceramic Construction Wet- formed sheet with organic bind er 3.3.2 Ceramic Content 86 - 94 % ceramic fiber 6 - 14 % organic binder 3.3.3 Ceramic Weight 160 Kg/cu meter +/- 10 % 3.3.4 Ceramic Thickness 1.50 +/- 0.13 mm 3.3.5 Aluminum Type 1100 or 1145 alloy, dead so

6、ft, oil free NOT TO BE USED FOR NEW DESIGN 2012 01 18 N Status No replacement named N. Benipal, NAENGINEERING MATERIAL SPECIFICATION ESA-M12G80-A2 Page 2 of 3 Copyright 2000, Ford Global Technologies, Inc. 3.3.6 Foil Thickne ss 0.076 +/- 0.013 mm 3.3.7 Laminating Adhesive Type Polyamide 3.3.8 Adhesi

7、ve Thickness 0.025 mm 3.4 PHYSICAL PROPERTIES (of the ceramic alone) 3.4.1 Temperature Resistance 1260 C Must withstand 1 hour at temperature in muffle furnace with no dimensional change. 3.4.2 Tensile Strength, min (ASTM D 828) MD & AMD 500 kN/sq.m 3.4.3 Mullen Burst, min 8.7 kPa (ASTM D 774) 3.4.4

8、 Tear Strength, min 350 g (ASTM D 689, for 75 mm wide sample) 3.4.5 Thermal Conductivity, target 0.04 W (m. C) (ASTM D 2214, modified method) 3.4.6 Adhesive Strength When the material is forcefully delaminated, the bond of the glass fiber to the adhesive shall be greater than the internal strength o

9、f the paper. 3.5 ADDITIONAL REQUIREMENTS Additional requirements for material and/or manufactured parts may be specified on the Engineering drawing, Engineering parts specification, performance specification, System Design Specification (SDS) and/or Component Design Specification (CDS). ENGINEERING

10、MATERIAL SPECIFICATION ESA-M12G80-A2 Page 3 of 3 Copyright 2000, Ford Global Technologies, Inc. 3.6 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes

11、to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notifica

12、tion of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this

13、document. The restrictions are identified in Restricted Substance Management Standard WSS- M99P9999- A1. 4. APPROVAL OF MATERIALS This specification is intended to define the performance and/or properties of finished parts or systems of combined materials. An Engineering Material Approved Source lis

14、ting is not applicable for this specification. Product Engineering materials referenced in this document and/or the affected engineering drawing, which require prior Engineering approval, are shown in the Engineering Material Approved Source List under the specification cited. 5. GENERAL INFORMATION

15、 The information given below is provided for clarification and assistance in meeting the requirements of this specification. The physical properties noted in section 3.4 are for the ceramic material only. The properties will differ significantly from the stated values depending on whether foil is laminated to one or both sides of the ceramic. Contact the supplier where further values on the laminate itself are required.