ImageVerifierCode 换一换
格式:PDF , 页数:1 ,大小:61.98KB ,
资源ID:744979      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-744979.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD ESA-M4P8-C-2003 HARDCOAT ANODIZE FINISH FOR ALUMINUM - UNSEALED TO BE USED WITH FORD WSS-M99P1111-A 《用于不密封的铝面的阳极化处理硬涂层 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(sumcourage256)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD ESA-M4P8-C-2003 HARDCOAT ANODIZE FINISH FOR ALUMINUM - UNSEALED TO BE USED WITH FORD WSS-M99P1111-A 《用于不密封的铝面的阳极化处理硬涂层 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2003 08 28 Revised Para 3.0 inserted; Para 3.6 & 4 deleted 1979 08 17 Released CW2K-822892-C Printed copies are uncontrolled Copyright 2003, Ford Global Technologies, Inc. Page 1 of 1 HARDCOAT ANODIZE FINISH FOR ALUMINUM UNSEALED ESA-M4P8-C 1.

2、 SCOPE This specification covers the hard coating of aluminum parts. 2. APPLICATION This process is generally used to provide added wear resistance to aluminum parts for use in brake systems. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers mus

3、t conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 PROCESS The method used shall be an electrolytic treatment with the part forming the anode and with contact points on non-critical portions of the part. The parts shall not be sealed. Washing in water at 6

4、5 C max temperature to facilitate drying is permissible. 3.2 COATING THICKNESS, min 0.0127 mm 3.2.1 Test Method: Microscopic examination (Umpire Method) is performed by direct measurement under the microscope. The sample to be measured is mounted and polished as for metallographic examination so tha

5、t a cross section of the film (coating) is presented to view. The coating thickness is determined by measurement with a calibrated micrometer eyepiece. Alternate methods of thickness determination which the supplier can demonstrate as correlating with microscopic examination are permissible. 3.3 UNI

6、FORMITY OF COATING The hard coating shall be continuous, smooth, adherent, uniform in appearance and shall be free from powdery areas, loose films, discontinuities such as breaks and scratches or other damage. The size and number of contact marks shall be kept to a minimum consistent with good pract

7、ice. 3.4 SURFACE HARDNESS File hard to Rc 50 file using test procedure outlined in SAE J 864. Test must be performed on area of sample such that the full width of the file can be utilized. File width should be no greater than 12 mm. 3.5 PROCESS CONTROL All processing must be documented. Any changes in processing must have prior engineering approval.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1