ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:42.90KB ,
资源ID:745042      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-745042.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD ESB-M11P8-A-2013 ADHESION REQUIREMENTS PRESSURE SENSITIVE ADHESIVE - SPONGE RUBBER TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(livefirmly316)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD ESB-M11P8-A-2013 ADHESION REQUIREMENTS PRESSURE SENSITIVE ADHESIVE - SPONGE RUBBER TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2013 12 11 N Status No replacement named L. Sinclair, NA 2007 06 27 Revised Inserted 3.0; Deleted 3.4 & 4 1965 06 14 Released AV1 #931 Controlled document at www.MATS Copyright 2013, Ford Global Technologies, LLC Page 1 of 2 ADHESION REQUIREM

2、ENTS, PRESSURE SENSITIVE ADHESIVE - ESB-M11P8-A SPONGE RUBBER NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the bond requirements for pressure sensitive adhesive coated sponge rubber. 2. APPLICATION This specification was released originally for assemblies consisting of pressure

3、sensitive, closed cell sponge rubber, bonded to chromium plated substrates. The pressure sensitive adhesive is intended as an assembly aid. Consequently, it should be used only where the sponge rubber is mechanically retained in final assembly. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTIO

4、N MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 ADHESION (ASTM D 903) 3.1.1 As Received, min 60 oz/in (0.66 N/mm) of width 3.1.2 Aged, min 3.1.2.1 Heat Aged 20 oz/in (0.22 N/mm) of width Test Method:

5、Condition of specimens for 14 days in a mechanical convection oven at 88 +/- 1 C. Allow a 4 h recovery at 23 +/- 2 C and 50 +/- 5% relative humidity before checking adhesion. 3.1.2.2 Humidity Aged 40 oz/in (0.44 N/mm) of width Test Method: Condition the specimens for 14 days at 95 - 100% relative hu

6、midity and 37 +/- 1 C. Allow a 4 h recovery at 23 +/- 2 C and 50 +/- 5% relative humidity before checking adhesion. 3.2 QUALITY The release film shall readily be removed from the pressure sensitive adhesive so as not to interfere with normal production processing. The bonded sponge rubber shall be s

7、ecurely retained and shall not fall off in normal shipping and handling. ENGINEERING MATERIAL SPECIFICATION ESB-M11P8-A Copyright 2013, Ford Global Technologies, LLC Page 2 of 2 3.3 SPONGE RUBBER As specified on the engineering drawing. 5. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 TEST SAMPLES When the production parts do not lend itself to testing, suitable test specimens shall be prepared from typical production slab stock materials.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1