ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:73.35KB ,
资源ID:745423      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-745423.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD ESB-M3G147-A-2005 TAPE CELLULOSE - PRESSURE SENSITIVE TO BE USED WITH FORD WSS-M99P1111-A 《压敏纤维素胶带 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(fatcommittee260)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD ESB-M3G147-A-2005 TAPE CELLULOSE - PRESSURE SENSITIVE TO BE USED WITH FORD WSS-M99P1111-A 《压敏纤维素胶带 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2005 11 28 Revised Inserted 3.0, Deleted 3.1, 3.2, 3.10, 4 1985 09 09 Released CAP1-DR533561 L. W. Moriarty Printed copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 1 of 3 TAPE, CELLULOSE - PRESSURE SENSITIVE ESB-M3G1

2、47-A 1. SCOPE The material defined by this specification is a cellulose (cellophane) pressure sensitive tape. 2. APPLICATION This specification was released originally for material used for identification purposes on ignition wire assemblies. 3. REQUIREMENTS: 3.0 STANDARD REQUIREMENTS FOR PRODUCTION

3、 MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 APPEARANCE The labels shall be free of streaks, blisters, wrinkles, ragged edges, and any other surface imperfections which will make them unsuitable for

4、 the intended usage. The design and color shall be as specified on the engineering drawing. 3.4 SETTING TIME FOR NORMAL HANDLING The label shall set sufficiently to permit normal handling immediately after application. 3.5 PHYSICAL PROPERTIES 3.5.1 Tensile Strength, min 4.4 N/mm width (ASTM D 1000)

5、3.5.2 Elongation, min 15% (ASTM D 1000) 3.5.3 Unwind Pull, max 350 N/mm width (ASTM D 1000) 3.6 FILM PROPERTIES 3.6.1 Appearance Specified on Engineering Drawing 3.6.2 Thickness (ASTM D 100) Tape Plus Adhesive, min 0.05 mm ENGINEERING MATERIAL SPECIFICATIONESB-M3G147-APrinted copies are uncontrolled

6、 Copyright 2005, Ford Global Technologies, LLC Page 2 of 3 3.6.3 Gloss (FLTM BI 110-01) The gloss of production material shall not vary more than +/- 7 units with a 60 (1 rad) glossmeter. 3.7 PREPARATION OF LABELS ON TEST PANELS Except where otherwise noted, test shall be conducted on the convolute

7、substrate part listed below. Tape to be wrapped around the convolute to ensure a suitable surface to surface bond. 3.7.1 Substrate 3.7.1.1 Nylon (Type 6) Heat Stabilized (ESF-M4D101-A) 3.8 RESISTANCE PROPERTIES After each of the resistance properties exposure, the film or label must not show evidenc

8、e of delamination, loss of printing, loss of adhesion, or any other effect which would detract from its proper function or appearance. 3.8.1 Humidity Resistance No curling of edges or visible loss of adhesion, blistering, and no loss of readability or any other effect which would detract from its pr

9、oper function or appearance. Test Method: Place the test panel in the humidity cabinet for 48 h at 38 +/- 1 C and 95 - 100% relative humidity. 3.8.2 Water Resistance, min 48 h (FLTM BI 104-01) No curling of edges or visible loss of adhesion or permanent change in color or gloss. The permanency of an

10、y color or gloss change shall be evaluated 7 +/- 1 h after the test panel is removed from the water bath and allowed to recover at 23 +/- 2 C and 50 +/- 5% relative humidity. 3.8.3 Heat and Cold Resistance No curling of the edges or other visible loss of adhesion in the specified 5 cycles of testing

11、. 4 h at 70 +/- 1 C 4 h at 38 +/- 1 C and 95 - 100% relative humidity 16 h at -29 +/- 1 C 3.8.4 Salt Spray Resistance, min 48 h (FLTM BI 103-01) No blistering, loss of adhesion, or permanent change in color or gloss. The permanency of any color or gloss change shall be evaluated 7 +/- 1 h after the

12、test panel is removed from the salt spray chamber and allowed to recover at 23 +/- 2 C and 50 +/- 5% relative humidity. ENGINEERING MATERIAL SPECIFICATIONESB-M3G147-APrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 3 of 3 3.8.5 Abrasion Resistance, min 100 cycles (F

13、LTM BN 108-02, CS-10 wheels, 500 g load) No visible substrate or loss of legibility is permitted in the abraded area. 3.8.6 Print Adhesion Place a ESB-M3G68-A cellophane or ESF-M3G40-A acetate fiber tape on the side of the film or label containing printing and remove with a quick snap. There shall b

14、e no effect on the printing. 3.8.7 Label Strength During installation the label must not break, tear, or deface. 3.9 FINISHED PARTS 3.9.1 Quality The quality required is that obtainable with the best commercial practice. 3.9.1.1 Cleanliness All substrates to be covered by the film shall be clean in

15、keeping with good commercial practice. Oil, grease, dust, and other foreign material which would affect the adhesion of the film shall be removed prior to material application. 3.9.1.2 Appearance Parts shall match initial samples approved by Quality Control for: Color and uniformity Smoothness (absence of blisters) Absence of scratches and tool marks

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1