FORD ESB-M4D464-A2-2010 ACETAL HOMOPOLYMER MODIFIED - HIGH IMPACT GRADE - PIGMENTED TO BE USED WITH FORD WSS-M99P1111-A 《着色高抗冲级改性聚甲醛均聚物 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2010 01 07 N-STATUS No replacement named J. Crist, NA 2000 09 29 Revised Removed ESB-M4D464-B2, updated & renumbered B. Xu 1985 10 28 CDP1-RD534418 Released Printed copies are uncontrolled Page 1 of 4 Copyri

2、ght 2010, Ford Global Technologies, Inc. ACETAL HOMOPOLYMER, MODIFIED - HIGH ESB-M4D464-A2 IMPACT GRADE - PIGMENTED NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a high impact modified homopolymer acetal thermoplastic compound. 2. APPLICATION This specification

3、 was released originally for material used for anti-theft door switches and seat belt shoulder strap loops. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to

4、 the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra

5、and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h pr

6、ior to testing and tested under the same conditions unless otherwise specified. 3.4 MOLDING COMPOUND 3.4.1 Melt Flow Rate See Corporate (ASTM D 1238, 190 C, 2.16 kg) Approved Source List ENGINEERING MATERIAL SPECIFICATION ESB-M4D464-A2 Page 2 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.4.2

7、 Melting Point 170 - 186 C (ASTM D 2133) 3.5 MOLDED TEST SPECIMENS 3.5.1 Preparation of Test Specimens All test specimens shall be injection molded in accordance with ASTM D 1897. The values of this specification are based on injection molded specimens unless otherwise specified. 3.5.3 Color The col

8、or must be approved for production by the Design Center Color Laboratory. 3.5.4 Specific Gravity 1.31 - 1.37 (ASTM D 792) 3.5.5 Tensile Strength at Yield, min 37 MPa (ASTM D 638, Type I specimen, 3.2 mm thick, 5.0 mm/min test speed) 3.5.5.1 Elongation at Break, min 100% 3.5.6 Flexural Modulus, min 1

9、.1 GPa (ASTM D 790, Method I, Procedure A, 3.2 x 12.7 x 127 mm specimen, 5 mm/min) 3.5.7 Impact Strength, Izod, min 745 J/m (ASTM D 256, 3.2 x 12.7 x 63.5 mm specimen) 3.5.8 Heat Deflection Temperature, min (ASTM D 648, 3.2 x 12.7 x 127 mm specimens) . At 0.45 MPa 100 C . At 1.82 MPa 70 C ENGINEERIN

10、G MATERIAL SPECIFICATION ESB-M4D464-A2 Page 3 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.6 FLAMMABILITY 3.6.1 Burn Rate, max 100 mm/min (FLTM BN 24-2, without the lot sampling plan) In addition, the test specimen shall not exhibit any flashing or sudden flaming on either surface in excess

11、 of the above max value. 3.7 ADDITIONAL REQUIREMENTS 3.7.1 Additional requirements for material and/or manufactured parts may be specified on the Engineering drawing, Engineering parts specification, performance specification, System Design Specification (SDS) and/or Component Design Specification (

12、CDS). 3.7.2 Accelerated Weather Resistance Rating 4 - 5 400 h Weatherometer (FLTM BO 101-1, specimen size: 70 x 100 mm minimum, 3.1 +/- 0.1 mm thick, molded in smooth polished mold) After exposure, the material shall show no fading or color change in excess of specified AATCC rating (AATCC Gray Scal

13、e for Evaluating Change in Color, 10 step). In addition, there shall be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be achieved by washing with mild detergents and water (ratio 5:95 by volume). NOTE: This requi

14、rement is applicable only for exposed color pigmented materials released for interior applications. ENGINEERING MATERIAL SPECIFICATION ESB-M4D464-A2 Page 4 of 4 Copyright 2010, Ford Global Technologies, Inc. 3.8 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent

15、 in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the

16、 affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested

17、. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to

18、 the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approv

19、al of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstra

20、ting full compliance with all the requirements of this specification. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 MOLD SHRINKAGE (ASTM D 955, after 48 h, injection molded sample) 1.6 mm avg. thickness 0.006 3.2 mm avg. thickness 0.012 6.4 mm avg. thickness 0.018 5.2 COEFFICIENT OF LINEAR THERMAL EXPANSION 1.2 x 10-4/C 5.3 HARDNESS, DUROMETER D 58 - 68 (ASTM D 2240, instantaneous reading)