FORD ESB-M6J93-A-2015 PRIMER WASH - CORROSION INHIBITING TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2015 01 22 N Status No replacement named G. Weber, NA 2008 04 16 Revised Inserted 3.0; Deleted 3.7 Revised 5. 1965 02 25 Released AV1 #778 Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 3 PRIMER, WASH

2、- CORROSION INHIBITING ESB-M6J93-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a corrosion inhibiting wash primer. This material is composed of a blend of chromate pigments and suitable resins and solvents to provide the required adhesion and corrosion resist

3、ance properties. This material is mixed thoroughly with ESB-M14J206-A Acid Catalyst Solvent before use. 2. APPLICATION This specification was released originally for primers used in low visibility areas to provide good adhesion for black-out enamel topcoats on zinc substrates and other metal surface

4、s where a phosphate coating cannot be applied. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 PHYSICAL PROPERTIES OF PRIMER 3.1.1 Non-Volatile,

5、min 10% (FLTM BI 102-01) 3.1.2 Weight Per Volume 7.3 +/- 0.3 (ASTM D 1475) lb/gal (0.87 +/- 0.03 kg/l) 3.1.3 Viscosity 25 +/- 5 s (FLTM BI 111-01) 3.1.4 Stability (FLTM BI 102-03) The material shall not jell or liver on standing. The viscosity shall not increase more than 10 s. 3.2 PHYSICAL PROPERTI

6、ES OF CATALYZED PRIMER 3.2.1 Mixing Ratio This material is catalyzed by thoroughly mixing the components in the following proportions: 4 parts (by volume) ESB-M6J93-A Wash Primer 1 part (by volume) ESB-M14J206-A Catalyst Solvent ENGINEERING MATERIAL SPECIFICATION ESB-M6J93-A Copyright 2015, Ford Glo

7、bal Technologies, LLC Page 2 of 3 3.2.2 Working Life The catalyzed material shall have a working life of 8 h min when mixed in drum quantities. Use of catalyzed primer after the 8 h period is not recommended. 3.2.3 Stability 3.2.3.1 Viscosity Stability (FLTM BI 111-01) The catalyzed primer shall not

8、 exhibit agglomeration of pigment or vehicle on hard settling. The viscosity shall not increase more than 5 s after 6 h aging at 38 +/- 1 C in a sealed container. 3.2.3.2 Adhesion and Performance Stability The catalyzed primer, when applied during its working life, shall meet the adhesion requiremen

9、ts of this specification. Test Method: Age catalyzed primer in a sealed container for 6 h at 38 +/- 1 C before preparing panels according to paragraph 3.3. Test for conformance to the following requirements. Adhesion (see paragraph 3.4.3) Water Resistance (see paragraph 3.5.1) 3.2.4 Toxicity This ma

10、terial shall contain no benzol (benzene), chlorinated or toxic compounds, or hydrolyzable chlorine derivatives, nor have any obnoxious or objectionable odors. 3.3 PREPARATION OF TEST PANELS Note: Duplicate panels must be prepared on two substrates. In addition, some tests must be performed on panels

11、 prepared with freshly catalyzed primer and material that has been aged after catalyzing (see paragraph 3.2.3.2). 3.3.1 Substrates 3.3.1.1 Bright Zinc; Conforming to ESF-M1P3-A 3.3.1.2 Galvanized Steel: Conforming to ESB-M1A59-A 3.3.2 Application of Primer Solvent wipe test panels with M14J210. Cata

12、lyze primer as described in paragraph 3.2.1 and spray apply a thin film (0.0001 - 0.0003 in (3 - 8 m). Allow to flash for 30 s and apply a 0.001 - 0.0015 in (26 - 38 m) (dry film thickness) coat of ESB-M2J200 quality black (1724 G) enamel. Bake 17 min at 129 C and age 72 h min at 23 +/- 2 C prior to

13、 testing. ENGINEERING MATERIAL SPECIFICATION ESB-M6J93-A Copyright 2015, Ford Global Technologies, LLC Page 3 of 3 3.4 FILM PROPERTIES 3.4.1 Appearance The enamel shall bake out to a presentable, serviceable film showing no craters, pinholes, seediness, nor abnormal roughness. 3.4.2 Total of Film Th

14、ickness 0.001 - 0.0015 in (FLTM BI 117-01) (26-38 m) 3.4.3 Adhesion No flaking or (FLTM BI 106-01) chipping 3.5 RESISTANCE PROPERTIES 3.5.1 Water Resistance, min 96 h (FLTM BI 104-01) Remove parts from water and immediately scribe lines through the enamel to the metal. Blow off entire painted surfac

15、e with air at 25 - 30 psi (173 - 206 kPa), using a 3/32 in (2.4 mm) orifice and holding the nozzle at approximately 45 and 1 - 2 in (25 - 50 mm) from the part, attempting to remove enamel film at scribe marks. Removal of paint beyond 1/8 in (3 mm) from any scribe mark shall be cause for rejection. B

16、listering shall be permitted. 3.5.2 Salt Spray Resistance, min 96 h (ASTM B 117) Remove parts from salt fog atmosphere and immediately scribe lines through the enamel to the metal. Blow off entire painted surface with air at 25 - 30 psi (173 206 kPa), using a 3/32 in (2.4 mm) orifice and holding the

17、 nozzle at approximately 45 and 1 - 2 in (25 - 50 mm) from the part attempting to remove enamel film at scribe marks. Removal of paint beyond 1/8 in (3 mm) from any scribe mark, blistering or peeling shall be cause for rejection. 5. GENERAL INFORMATION The information given below is provided for cla

18、rification and assistance in meeting the requirements of this specification. When mixed with the Acid Catalyst Solvent, ESB-M14J206-A, the catalyzed mixture has a pot life of approximately 8 h, hence, care should be taken to mix only that amount of material which will be used in an 8 h period. For satisfactory performance of this primer, it is essential that it be thinned only with Acid Catalyst Solvent, ESB-M14J206-A, supplied by the same vendor and that the mixing instructions be followed explicitly.