FORD ESF-M2L1-A-2015 COPPER WIRE SOFT OR ANNEALED ROUND - BARE TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2015 10 30 N Status No usage or replacement L. Sinclair, NA 2003 06 24 Revised Para 3.0 inserted; Para 3.8 & 4 deleted 1978 06 12 Metricated & Retyped CF4H-RD 567168-21 1963 07 29 Released F6-1092 Copyright 2015, Ford Global Technologies, Inc

2、. Page 1 of 3 COPPER WIRE, SOFT OR ANNEALED ROUND BARE ESF-M2L1-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is soft or annealed bare round copper wire. 2. APPLICATION This specification was released originally for material used for electrical purposes. 3. REQU

3、IREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 WIRE SIZE The wire size shall be specified on the engineering drawing and/or release according to the Am

4、erican Wire Gage number desired. Example: #28 Gage ESF-M2L1-A. 3.2 CHEMICAL COMPOSITION The copper shall be of such quality and purity that the finished product shall have the physical properties and electrical characteristics herein required. 3.3 ELECTRICAL RESISTIVITY The electrical resistivity at

5、 a temperature of 20 C shall not exceed the following values: . 875.20 Ohm lb/mile2 (0.15328 Ohm g/m2) . 10.371 Ohm cmil/ft (0.017241 Ohm mm2/m) Resistance for any given wire must fall within the range obtained by calculating resistance for both the high and low diameter. The following formula may b

6、e used: Resistivity x Length Resistance = Cross Section Resistance will be in Ohms. Resistivity - 10.371 (0.017241) Length - feet (metre) Cross Section - circular mils (square millimetres) The circular mils for any diameter wire may be calculated by squaring the number of thousandths of inches in an

7、y given diameter. ENGINEERING MATERIAL SPECIFICATION ESF-M2L1-A Copyright 2015, Ford Global Technologies, Inc. Page 2 of 3 3.4 TENSILE STRENGTH AND ELONGATION Awg Tensile Strength Elongation in 10 Size psi (MPa), max in (254 mm) %, min 0 - 0000 36,000 (248) 35 1 - 9 37,000 (255) 30 10 - 23 38,500 (2

8、65) 25 24 - 29 20 30 - 40 15 3.5 DIMENSIONAL TOLERANCES The bare wire size shall conform to the specified diameter within the permissible variations shown in Table I. 3.6 FINISH The finished wire shall be free from all imperfections not consistent with the best commercial practice. 3.7 JOINTS The wi

9、re shall be one continuous length for each spool. There shall be as few joints as possible in the copper and such joints as are necessary to bring the wire up to the required spool weight shall be made by brazing with silver solder, or by welding. The diameter of the wire at the joint shall be subst

10、antially the same as of any other point on the wire. The surface of the wire at the joint shall be smooth. The tensile strength of the wire at the joint shall be at least 80% of the tensile strength of the wire 3 - 4 ft (0.9 - 1.2 m) from the joint. 5. GENERAL INFORMATION The information given below

11、 is provided for clarification and assistance in meeting the requirements of this specification. 5.1 DENSITY For the purpose of calculating weights, the density of the copper shall be taken as 8.89 g/cm3 (0.32117 lb/in3) at 20 C. ENGINEERING MATERIAL SPECIFICATION ESF-M2L1-A Copyright 2015, Ford Glo

12、bal Technologies, Inc. Page 3 of 3 TABLE 1 BARE WIRE DIAMETER Awg Size Diameter Tolerance, Plus Only in mm in mm 7 0.1428 3.627 0.0030 0.076 8 0.1272 3.231 0.0026 0.066 9 0.1133 2.878 0.0022 0.056 10 0.1009 2.563 0.0020 0.051 11 0.0898 2.281 0.0018 0.046 12 0.0800 2.032 0.0016 0.041 13 0.0713 1.811

13、0.0014 0.036 14 0.0635 1.613 0.0012 0.030 15 0.0565 1.435 0.0012 0.030 16 0.0503 1.278 0.0010 0.025 17 0.0448 1.138 0.0010 0.025 18 0.0399 1.013 0.0008 0.020 19 0.0355 0.902 0.0008 0.020 20 0.0317 0.805 0.0006 0.015 21 0.0282 0.716 0.0006 0.015 22 0.0250 0.635 0.0006 0.015 23 0.0224 0.569 0.0004 0.0

14、10 24 0.0199 0.505 0.0004 0.010 25 0.0177 0.450 0.0004 0.010 26 0.0157 0.399 0.0004 0.010 27 0.0141 0.358 0.0002 0.005 28 0.0125 0.318 0.0002 0.005 29 0.0112 0.284 0.0002 0.005 30 0.0099 0.251 0.0002 0.005 31 0.0088 0.224 0.0002 0.005 32 0.0079 0.201 0.0002 0.005 33 0.0070 0.178 0.0002 0.005 34 0.00

15、62 0.157 0.0002 0.005 35 0.0055 0.140 0.0002 0.005 36 0.0049 0.124 0.0002 0.005 37 0.0044 0.112 0.0002 0.005 38 0.0039 0.099 0.0002 0.005 39 0.0034 0.086 0.0002 0.005 40 0.0030 0.076 0.0002 0.005 41 0.0027 0.069 0.0002 0.005 42 0.0024 0.061 0.0002 0.005 43 0.0021 0.053 0.0002 0.005 44 0.0019 0.048 0.0002 0.00