ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:39.71KB ,
资源ID:746334      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-746334.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD ESF-M99J293-D-2012 SILICONE COATING CONFORMAL - MEDIUM VISCOSITY TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESF-M99J293-A)《中粘度保形硅胶涂层 与福特WSS-M99P1111-A 一起使用 在福特ESF-.pdf)为本站会员(figureissue185)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD ESF-M99J293-D-2012 SILICONE COATING CONFORMAL - MEDIUM VISCOSITY TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESF-M99J293-A)《中粘度保形硅胶涂层 与福特WSS-M99P1111-A 一起使用 在福特ESF-.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revision Rev 03 2012 02 16 N Status No replacement named N. Benipal, NA 2005 08 15 Revised Inserted 3.0; deleted 3.3, 3.4 and 4 1977 04 28 Released (Was XF-M99JX9) F4G52 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page

2、 1 of 2 SILICONE COATING, CONFORMAL ESF-M99J293-A SILICONE COATING, CONFORMAL - LOW VISCOSITY ESF-M99J293-B SILICONE COATING, CONFORMAL - MEDIUM VISCOSITY ESF-M99J293-D NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by these specifications are silicone conformal coatings which may be c

3、ured by air drying or baking. 2. APPLICATION These specifications were released originally for materials used as a conformal coating on the circuit board in the electronic engine control module. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers

4、must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 FOR LOT APPROVAL A B D 3.1.1 Non-volatiles, % min 70 25 50 (FLTM BI 102-01) 3.1.2 Viscosity at 25 C, mPa.s 600-1000 60-100 100-180 (ASTM D 446) 3.1.3 Specific Gravity 1.02-1.10 0.80-0.85 0.97-1.0 (ASTM

5、D 154 at 25 C) 3.1.4 Drying Time, max Tack free in 24 h or 30 min (2 mil film at 25 C and at 25 C and 50% R.H. plus 30 50% R.H.) min at 100 C 3.1.5 Flash Point, C, min 11 15 5 (ASTM D 93 closed) 3.2 TESTS TO BE RUN FOR INITIAL APPROVAL AND AS REQUIRED BY QUALITY CONTROL Tests to be run on 0.8 mm thi

6、ck clean CRLC panels dipped and cured 24 h at 25 C. Thickness of coating to be 0.05-0.10 mm. 3.2.1 Dielectric Strength, min 50 kV/mm (ASTM D 115 - short time) ENGINEERING MATERIAL SPECIFICATION ESF-M99J293-A/B/D Copyright 2012, Ford Global Technologies, LLC Page 2 of 2 3.2.2 Heat Resistance No blist

7、ering, (24 h at 210 C) flaking or loss of adhesion 3.2.3 Salt Spray, min 100 h (ASTM B 117) 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of these specifications. 5.1 FLAMMABILITY AND/OR TOXICITY This material represents a

8、 potential fire and/or health hazard. The Manufacturing Engineering Department must notify both the Plant Security and the Safety personnel of its presence in the plant to assure that proper fire and/or health precautions are provided. The location in which it is used or stored must be included in the notification.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1