FORD FLTM AN 102-02-2001 DETERMINATION OF WEIGHT OF COMPONENTS IN POLYETHYLENE-BACKED CARPET (Replaces FLTM EU-AN 002-02)《聚乙烯作衬地毯成分重量的测定》.pdf

1、 FORD LABORATORY TEST METHOD AN 102-02 Date Action Revisions 2001 01 30 Revised Editorial no technical change A. Cockman 2000 04 14 Editorial no technical change A. Cockman 1994 09 13 Printed copies are uncontrolled Page 1 of 4 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF WEIGHT O

2、F COMPONENTS IN POLYETHYLENE-BACKED CARPET Application This procedure is used to determine the weight of the various components of polyethylene-backed automotive carpeting materials used as floor coverings, luggage liners, trim panels and other applications. This extraction procedure will remove pol

3、yethylene, wax and other materials which are soluble in toluene or xylene. Apparatus Required Beakers One - 2000 mL Two - 1000 mL Watch Glass Appropriate size to cover 2000 mL beaker. Hot Plate Flameless hot plate - capable of maintaining the solvent at a moderate boil. Drying Ovens Mechanical Conve

4、ction - capable of being maintained at 38 +/- 2 C and 102 +/- 2 C. Screen U. S. No. 50 mesh sieve Desiccator Analytical Balance Accurate to +/- 0.0001 g. Cutting Die 152.4 x 152.4 mm FORD LABORATORY TEST METHOD AN 102-02 Page 2 of 4 Copyright 2001, Ford Global Technologies, Inc. Materials Required F

5、ilter Paper Whatman No. 42 or equivalent Absorbent Paper Towel Xylene or Toluene Technical grade. CAUTION: Low flash point. Refer to Fire Control Bulletin No. 18. Desiccant Drierte or equivalent. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a

6、 controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Die cut three test specimens across the width of the carpet. Each sample should be cut at least 250 mm from the

7、edge of the roll. 2. Clean and dry the beakers and place in an oven for 15 minutes at 102 C. 3. Remove the beakers from the oven and place in a desiccator. Allow to cool to 23 +/- 2 C. 4. Weigh each beaker to the nearest milligram (1000 mL beaker = W1 and W1*; 2000 mL beaker = W2). 5. Place a test s

8、pecimen in the 2000 mL beaker and record weight (W3). W3 - W2 = Weight of test specimen (W4) 6. Add approximately 600 mL of xylene or toluene to the 2000 mL beaker containing the sample, and cover with a watch glass. 7. Place the beaker on a hot plate and adjust the hot plate to maintain moderate bo

9、iling of the solvent. 8. Boil for 10 minutes, then rotate the sample and boil for at least another 10 minutes until all of the polyethylene visually appears to be in solution. FORD LABORATORY TEST METHOD AN 102-02 Page 3 of 4 Copyright 2001, Ford Global Technologies, Inc. 9. Pour off the xylene thro

10、ugh the 50 mesh sieve to collect any loose fiber in the solution. Place the solvent-treated sample and all the loose fiber on a sheet of filter paper, backed by several sheets of absorbent paper towel. Allow the solvent to evaporate from the sample under a hood for one hour, then dry the sample in a

11、n oven at 38 +/- 2 C for one hour. 10. Remove the sample from the oven and condition for a minimum of 4 hours at 23 +/- 2 C and 50 +/- 5 R.H. 11. For a Needled Carpet: Place the sample and all loose fiber in one of the tared 1000 mL beakers. Weigh the beaker and sample and loose fiber (W5). Calculat

12、e the weight, in grams, of the sample and loose fiber (W6) by subtracting the weight of the tared beaker (W1). Weight of sample and loose fiber (W6) = W5 - W1. Obtain the weight of the polyethylene (W7) as follows: Weight of polyethylene (W7) = W4 - W6 12. For a Tufted Carpet: A. Carefully separate

13、the pile (using fingers or equivalent technique) from the tufting foundation. Place the pile fiber in one of the tared 1000 mL beakers (W1), along with any loose fiber in the filter paper. Place the tufting foundation in the other tared beaker (W1*). B. Weigh each beaker with the samples and record

14、the weight. Weight of pile fiber and beaker = Wp; weight of tufting foundation and beaker = WT. Calculate the weight of the pile fiber (W8) and tufting foundation (W9) by subtracting the weight of the tared beakers. Weight of pile fiber (W8) = Wp - W1 Weight of tufting foundation (W9) = WT - W1* C.

15、Calculate the weight of the polyethylene (W7) as follows: Weight of polyethylene (W7) = W4 - (W8 + W9) 13. Convert the weight (grams) of the various carpet components to a weight/unit area as required in the applicable material specification. To get: kg/m2 - multiply results by 0.043 FORD LABORATORY

16、 TEST METHOD AN 102-02 Page 4 of 4 Copyright 2001, Ford Global Technologies, Inc. 14. Report weight of pile fiber, primary and secondary backings (if applicable), and polyethylene backcoating. 15. Repeat for second and third samples. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.