ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:39.79KB ,
资源ID:746820      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-746820.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM AQ 002-01-2001 CONTROL TESTS FOR PHOSPHATE COATING PROCESS《磷酸盐涂层工艺的控制试验》.pdf)为本站会员(postpastor181)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM AQ 002-01-2001 CONTROL TESTS FOR PHOSPHATE COATING PROCESS《磷酸盐涂层工艺的控制试验》.pdf

1、 FORD LABORATORY TEST METHOD AQ 002-01 Date Action Revisions 2001 01 31 Revised Editorial no technical change A. Cockman 2000 04 19 Editorial no technical change A. Cockman 1992 05 01 Printed copies are uncontrolled Page 1 of 7 Copyright 2001, Ford Global Technologies, Inc. CONTROL TESTS FOR PHOSPHA

2、TE COATING PROCESS Application These test methods are used where applicable to check the concentration of the solutions used in the phosphate coating process described in the Material Standards PL 53-07, PL 53-09, and PL 53-32. The analytical techniques listed which utilize a “point system“ for the

3、titration of solutions is designed to provide for simple conversion of results in points to concentration of a solution. This procedure eliminates the need for relatively complicated manipulations of gram equivalent weights, specific gravity, etc. If it is necessary to express concentrations in actu

4、al percentage concentrations this may be accomplished by substituting into the following conversion formula. % unknown = mL titer used x normality x factor x 100 wt. sample Solutions Required See Ford Laboratory Test Method AZ 2-1 for preparation of solutions and indicators. Standard Sodium Hydroxid

5、e 0.1 N Reagent No. 1 Standard Hydrochloric Acid 0.1 N Reagent No. 4 Standard Potassium Permanganate 0.042 N Reagent No. 9 Use 1.34 g and dilute to 1 liter or take 420 mL of 0.1 N solution and dilute to 1 liter. titration factor = normality 0.042 Standard Potassium Ferrocyanide Reagent No. 12 Standa

6、rd Ferrous Sulfate Solution 0.1 N Reagent No. 10 Standard Sodium Thiosulfate Solution 0.1 N Reagent No. 14 Standard Potassium Dichromate Solution 0.1 N Reagent No. 15 Indicators Phenolphthalein Reagent No. 101 Brom Cresol Green Reagent No. 108 Brom Phenol Blue Reagent No. 109 Diphenylamine Reagent N

7、o. 110 Iron Test Paper Reagent No. 111 Starch Solution Reagent No. 113 Orthophenanthroline Reagent No. 114 FORD LABORATORY TEST METHOD AQ 002-01 Page 2 of 7 Copyright 2001, Ford Global Technologies, Inc. Titrating and Indicator Solutions Supply List Prepared solutions required for control tests may

8、be obtained from the Amchem Products, Inc. or Parker Rust Proof Co. when ordered by their respective numbers as shown: Standard Solutions Amchem Parker Sodium Hydroxide 0.1 N 11 11 Hydrochloric Acid 0.1 N 20 - Potassium Permanganate 0.042 N 15 15 Sulphuric Acid 0.1 N - 20 Potassium Ferrocyanide (1 g

9、 = 0.015 g/Zn) 16 - Sodium Thisulfate 0.1 N 31 - Ferrous Sulfate 0.1 N - 31 Potassium Dichromate 0.1 N - 30 Indicators Amchem Parker Phenolphthalein 3 3 Brom Cresol Green 2 2 Brom Phenol Blue 10 11 Diphenylamine 7 7 Indicator Paper Iron 2005 17 Orthophenanthroline - 12 Conditioning and Test Conditio

10、ns All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure Test A Cleaner Control Free Alkali 1. Pipet

11、 10 mL of sample into a 150 mL Erlenmeyer flask. 2. Add 5 drops of phenolphthalein indicator. 3. Titrate with 0.1 N HCl until solution changes from pink to colorless. 4. mL of HCl used = free alkali value. FORD LABORATORY TEST METHOD AQ 002-01 Page 3 of 7 Copyright 2001, Ford Global Technologies, In

12、c. Total Alkali 1. Pipet 10 mL of sample into a 150 mL Erlenmeyer flask. 2. Add 10 drops of brom cresol green indicator. 3. Titrate with 0.1 N HCl until color changes from purple red to yellow. 4. mL of 0.1 N HCl indicates total alkali value. Test B Rinse Water Control (After Alkaline Cleaning) Tota

13、l Alkali 1. Pipet 10 mL of the rinse water into a 150 mL Erlenmeyer flask. 2. Add 5 drops of brom cresol green indicator. 3. Titrate with 0.1 N HCl to yellow end point. Report mL of HCl as total alkali value 4. If solution turns yellow after addition of indicator, discard sample and proceed as follo

14、ws: (See Note) (a) Pipet 10 mL of sample into a 150 mL Erlenmeyer flask. (b) Add 5 drops of phenolphthalein indicator. (c) Titrate with 0.1 N NaOH to a pink color. (d) mL of 0.1 N NaOH = points total acid Note: This is an abnormal condition and indicates that phosphate solution is getting into the r

15、inse water, possibly through a misdirected nozzle. Test C Phosphate Coating Control M1178C or M3B1 with M13844 Accelerator Total Acid 1. Pipet 10 mL of sample into a 150 mL Erlenmeyer flask. 2. Add 5 drops of phenolphthalein indicator. 3. Titrate with 0.1 N NaOH to the development of a pink color. 4

16、. mL of 0.1 N NaOH = points total acid. FORD LABORATORY TEST METHOD AQ 002-01 Page 4 of 7 Copyright 2001, Ford Global Technologies, Inc. Free Acid 1. Pipet 10 mL of sample into a 150 mL Erlenmeyer flask. 2. Add 3 drops of brom phenol blue indicator. 3. Titrate with 0.1 N NaOH to a color change from

17、yellow to light blue. 4. mL of 0.1 N NaOH used = free acid points. Accelerator Test Before testing for the amount of accelerator, dip a strip of iron test paper in phosphate solution. If the paper turns pink, it is an indication that no accelerator is present. Small additions of accelerator should b

18、e made to the phosphate solution tank until no change in color of a fresh indicator paper occurs. When no change in color of the test paper appears, proceed to determine the amount of accelerator as follows: 1. Pipet 25 mL of the phosphate solution into a 150 mL Erlenmeyer flask. 2. Add 10 20 drops

19、of dilute C.P. H2SO4 (1:1). 3. Titrate with standard 0.042 N KMnO4 drop by drop while swirling; until a persistent pink color is obtained which remains for 10 seconds. 4. mL of KMnO4 x titration factor = points of accelerator present. Test D Phosphate Coating Control M1171B with M1172B Accelerator A

20、ccelerator Test 1. Pipet 10 mL of the filtered bath into a 350 mL Erlenmeyer flask. 2. Dilute to 100 mL with water. 3. Add 10 mL of dilute H2SO4 (1:1). 4. Titrate to a permanent pink color with 0.042 N. KmnO4. 5. The number of mL of KmnO4 used x titration factor is the accelerator concentration. (Sa

21、ve Sample for phosphate test.) FORD LABORATORY TEST METHOD AQ 002-01 Page 5 of 7 Copyright 2001, Ford Global Technologies, Inc. Phosphate Test Based on Zinc Content of Bath 1. Add 0.5 mL of standard KmnO4 (0.042 N) to the sample just titrated for accelerator. 2. Add 3 4 drops of diphenylamine indica

22、tor. 3. Titrate with standard potassium ferrocyanide to a green end point as follows: Add 2 drops of titrating solution at a time, swirling 5 seconds between additions. Continue until the color of the solution changes to a light blue and then a violet. At this point add only 1 drop of the titrating

23、solution at a time, swirling for 30 seconds between additions. The end point is reached when a light green color persists which does not revert to a violet color on stirring. The end point is a very sharp if instructions are followed exactly. 4. The number of mL potassium ferrocyanide used x factor

24、is the concentration of the phosphate coating based on the zinc content. Test E Chromic Phosphoric Control Free Acid 1. Pipet 25 mL of test solution into a 150 mL Erlenmeyer flask. 2. Add 4 drops of brom cresol green indicator. Note: If the color of the sample turns from yellow to green after adding

25、 indicator, it indicates that no free acid is present; that additional chromic-phosphoric acid M13879 should be added to the rinse tank and another test made. 3. If the solution remains yellow, titrate to a green color with 0.1 N NaOH. Note: Save sample for Total Acid Test. 4. mL of 0.1 N NaOH used

26、indicates the points of free acid present. Total Acid 1. Add 5 drops of phenolphthalein to the sample used in the Free Acid Test and continue titrating with 0.1 N NaOH to a violet color which will last for 15 seconds. 2. The total number of mL of 0.1 N NaOH used in the Free Acid and Total Acid Tests

27、 is points of total acid present. FORD LABORATORY TEST METHOD AQ 002-01 Page 6 of 7 Copyright 2001, Ford Global Technologies, Inc. Test F Babcock Number Zinc Phosphate for Cold Forming PL 53-32 This test requires the use of a conical graduate, 100 mL Cassia flask, and a water bath. 1. Measure 50 mL

28、of the holt lubricant (190 +/- 5 F) into a conical graduate. 2. Pour into a 100 mL Cassia flask, rinsing the graduate into the flask with 20 25 mL of hot water. 3. Place the flask in a boiling water bath for 3 5 minutes. 4. Add 10 mL of dilute H2SO4 (1:1) and swirl the flask to mix thoroughly. 5. Pl

29、ace in the water bath and, after 15 minutes, add hot boiled water to bring the oily layer into the neck of the flask. 6. After 5 minutes, when the oily layer has separated sharply, take the readings of the lower and upper edges of the clear oily column in the neck while the flask is still in the wat

30、er bath. 7. The difference between the two readings is reported as the Babcock number. Test G Hexavalent Chromium Two optional methods are shown Method No. 1 for Amchem Products material and Method No. 2 for Parker Rust Proof material. Method No. 1 1. Pipet 25 mL of the sample into a 250 mL iodimetr

31、ic flask and dilute to 100 mL with distilled water. 2. Add approximately 1 g of potassium idodide and agitate until dissolved. 3. Add 15 mL of HCl (conc.) in 5 mL increments to the lip of the flask and raise the stopper slightly after each addition to allow the acid to run into the flask. 4. Rinse t

32、he lip of the flask several times with distilled water and replace the stopper. 5. After 1 minute, titrate the solution with 0.1 N sodium thiosulfate (Reagent No. 14) until a straw color is obtained. 6. Add 3 5 mL of soluble starch solution (Indicator No. 113) and continue the titration until the bl

33、ue-black color disappears. 7. The total number of mL of titrating solution used is the points of hexavalent chromium present. FORD LABORATORY TEST METHOD AQ 002-01 Page 7 of 7 Copyright 2001, Ford Global Technologies, Inc. Method No. 2 1. First be sure that the free acid is in the operating range. 2

34、. Pipet 25 mL of sample into a 250 mL beaker and add 25 mL of H2SO4 (1:1). 3. Add 35 mL of distilled water and 2 drops of orthophenanthroline (Indicator No. 114). 4. Titrate with 0.1 N ferrous sulfate (Reagent No. 10) until the solution changes through blue to a reddish brown color. Calculate points

35、 of hexavalent chromium (Parcolene 8) as follows: Points = mL 0.1 N FeSO4 x C (correction factor) Note: The 0.1 N FeSO4 is not stable and must be standardized weekly to determine its correction factor “C“ as follows: (a) Pipet 10 mL of 0.1 N potassium dichromate solution (Reagent No. 15) into a 250

36、mL beaker. (b) Add 25 mL of H2SO4 (1:1), 50 mL of distilled water and 2 drops of orthophenanthroline (Indicator No. 114). (c) Titrate with 0.1 N FeSO4 solution until the color changes through blue to a reddish brown color. Correction Factor “C“ = 10 (mL dichromate) mL of ferrous sulfite used Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper used and handling in its facilities.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1