ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:63.56KB ,
资源ID:747018      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747018.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM BI 120-2-2001 DETERMINATION OF THROWING POWER OF ELECTROCOATING MATERIALS (Replaces FLTM BI 020-02 A FLTM BI 020-02 C FLTM EU-BI 020-02 A FLTM EU-BI 020-02 C).pdf)为本站会员(王申宇)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM BI 120-2-2001 DETERMINATION OF THROWING POWER OF ELECTROCOATING MATERIALS (Replaces FLTM BI 020-02 A FLTM BI 020-02 C FLTM EU-BI 020-02 A FLTM EU-BI 020-02 C).pdf

1、 FORD LABORATORY TEST METHOD BI 120-02 Date Action Revisions 2001 03 19 Revised Editorial no technical change A. Cockman 1991 05 28 Printed copies are uncontrolled Page 1 of 5 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF “THROWING POWER“ OF ELECTROCOATING MATERIALS Application Thi

2、s test is used to determine the ability of electrocoating materials to extend a protective coating into recessed areas. Apparatus and Materials Required Power Source Zero to 1000 Volt DC Zero to 10 Amp. Note 1: The maximum peak to peak value of the primary AC ripple must not exceed 10 % of the indic

3、ated coating voltage. Note 2: Equipment having a lower voltage range may be used providing voltages higher than the maximum required by the materials are available. Coating Tank Cylindrical non-conducting, acid resistant container, e.g. glass, having a minimum internal diameter of approximately 150

4、mm and a height of approximately 320 mm. Laboratory Stirrer (Acid Resistant) Zero to 700 rpm, electrically insulated shaft of suitable design to give adequate circulation. Throwing Power Box (See Drawing) This is an open ended box made using two 105 x 300 mm test panels and two insulated acid resist

5、ant strips 10 x 4 x 300 mm. The strips are inserted between the edges of the panels which are then fixed together using waterproof insulating tape or clips to prevent deposition beneath the strips. The cathode holder shall have dimensions giving satisfactory electrical contact with both test panels.

6、 FORD LABORATORY TEST METHOD BI 120-02 Page 2 of 5 Copyright 2001, Ford Global Technologies, Inc. Test Panels and Anode Ford Quality Control approved test panels UMA0018005 - (phosphated) or as specified in the relevant material specification. The two panels are electrically connected by a conductin

7、g bridge using crocodile clips. Phosphate coated panels must be dried at 105 C (metal temperature) for 3 minutes minimum, stored in a desiccator up to 24 hours or used within 1 hour. Note: Alternative panels may be used for special test purposes, e.g. Plant phosphated panels, after notification and

8、agreement with Quality Control. The type of phosphate and coating weight used must be stated. This coating must be in accordance with WSK-M3P1-C unless otherwise stated in the material specification. Thermostat Capable of controlling bath temperature to +/- 2 C. Note: A coolant system is necessary t

9、o maintain the bath at 20 C or as currently used in production. The cooling tube must be acid resistant. Mechanical Convection Oven Capable of maintaining temperatures up to 200 C within +/- 2 C. Low Conductivity Water Conductivity must not be greater than 10 uS/cm at 20 C. Electrode Holder (Insulat

10、ing Material) To support cathode (test box) and anode panel (105 x 300 mm) parallel to each other and 50 mm apart. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not les

11、s than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST METHOD BI 120-02 Page 3 of 5 Copyright 2001, Ford Global Technologies, Inc. Procedure 1. A paint sample is stirred with a spatula allowing the tip to contact the bottom of the container

12、. Mixing is adequate if no evidence of settling is indicated when the spatula is withdrawn and examined. 2. A suitable quantity of material is made up using the specified formulation. The solids, pH, and conductivity should be adjusted to suppliers recommendation. This sample is stirred for 16 hours

13、 minimum before use. Note: Production tank samples are used as received, without additions. Suitable stirring time after sampling and transportation is required immediately on arrival at appropriate laboratory. 3. Position the stirrer in the tank so that the propeller is at least 25 mm from the bott

14、om. The desired amount of paint is then poured into the tank and stirred. Note: Stirring speed must be sufficiently low to ensure that in this and subsequent operations air will not be induced. 4. Control the bath at an operating temperature of 20 +/- 2 C or as recommended by the supplier. 5. Positi

15、on the throwing power box and anode in the tank so that the lower end is 50 +/- 5 mm from the bottom. 6 Connect the cathode (both panels of box) and the anode to the power source. 7. The voltage is raised from zero to the coating voltage within 15 seconds. Maintain the voltage for 120 seconds and th

16、en reduce to zero in 2 seconds. Note: The coating voltage shall be the same as that determined for preparing test panels at the specified film thickness. 8. Remove the box assembly from the tank. Rinse with the low conductivity water and remove surplus water with oil free compressed air. Separate te

17、st panels, rinse and redry as before. Note: Clean the insulated strips ready for use again. 9. Bake the electrocoated test panels in accordance with the relevant material specifications. 10. Age the electrocoated panels for either 16 hours at 45 +/- 2 C or 72 hours at 23 +/- 2 C. FORD LABORATORY TES

18、T METHOD BI 120-02 Page 4 of 5 Copyright 2001, Ford Global Technologies, Inc. Evaluation 1. Measure the length of the thrown paint film on each metal panel. The average length in mm is the visual throwing power of the paint. Measure the wedge length from bottom edge of panel at 10 micrometre film th

19、ickness along the line of the throw. 2. To determine the “Salt Spray Throwing Power“: Tape the long sides of the test panels to prevent rusting of the unpainted edges. Do not “X“ scribe the panels. Expose the test panels to a 240 hour salt spray test in accordance with ASTM B 117 unless otherwise sp

20、ecified in the relevant material specification. Rinse the panels with water. Remove excess water with compressed air and examine for blistering and rusting. Do not consider edge rusting. Measure the distance from the painted end of the test panel to the point at which blistering and/or rust are evid

21、ent. This distance in mm is the “Salt Spray Throwing Power“ of the material under test. 3. Report the following in mm: a) Visual throw b) 10 micrometre line c) Throwing power corrosion line Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BI 120-02 Page 5 of 5 Copyright 2001, Ford Global Technologies, Inc. THROWING POWER BOX

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1