ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:26.87KB ,
资源ID:747209      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747209.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM BN 105-1-2000 SHRINKAGE TEST FOR TEXTILES AND ARTIFICIAL LEATHERS (Replaces FLTM BN 005-01 FLTM EU-BN 005-01).pdf)为本站会员(eveningprove235)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM BN 105-1-2000 SHRINKAGE TEST FOR TEXTILES AND ARTIFICIAL LEATHERS (Replaces FLTM BN 005-01 FLTM EU-BN 005-01).pdf

1、 FORD LABORATORY TEST METHOD BN 105-01 Date Action Revisions 2000 08 07 Editorial no technical change A. Cockman 1992 02 07 Printed copies are uncontrolled Page 1 of 2 Copyright 2000, Ford Global Technologies, Inc. SHRINKAGE TEST FOR TEXTILES AND ARTIFICIAL LEATHERS Application This procedure is use

2、d to determine the dimensional changes of textile seating fabrics, artificial leathers, carpet materials and other similar materials after wetting and subsequent drying . Apparatus Required Water Tray Having the following minimum dimensions: 300 x 300 mm, 50 mm deep 300 x 300 mm wire mesh screen Wit

3、h weights or glass rods. Distilled Water Cutting Dies 300 x 300 mm 250 x 250 mm Indelible Ink Cutting Tool Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than

4、 24 h prior to testing and tested under the same conditions unless o therwise specified. Procedure 1. Preferred Method Die cut a 300 x 300 mm specimen. Make a 25 mm cut on each of the sides of 250 x 250 mm section midway between the corners with the cutting tool. FORD LABORATORY TEST METHOD BN 105-0

5、1 Page 2 of 2 Copyright 2000, Ford Global Technologies, Inc. Alternative Method Mark off a 250 x 250 mm section wi th indelible ink with a line as fine as possible. For carpets cut a 250 x 250 mm specimen directly. 2. Place the test specimen in a tray containing distilled water at 23 +/ - 2 C and ke

6、ep it immersed until it is thoroughly soaked. The immersion period s hall be a minimum of one hour. To prevent movement of the test specimen to the surface, use the wire mesh screen to weigh it down, if necessary using additional weights or glass rods. 3. After thoroughly soaking, lay the test speci

7、men flat on a raised wi re mesh screen (removing weights or glass rods from the specimens surface) and allow the specimen to dry using a low temperature forced air system for a minimum of 24 hours at 23 +/ - 2 C and a relative humidity of 50 +/ - 5 %, if not otherwise specified, until it reaches moi

8、sture equilibrium with that of the room. 4. Measure the dimensional changes of the test specimen, i.e. shrinkage or the extension of the specimen, within the area of the marked square. Evaluation Calculate the shrinkage or extensio n of the specimen and report the result as a plus or minus percentage. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its fac ilities.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1