FORD FLTM BN 108-09-2001 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CARPETS《汽车地毯的结须和结霜试验》.pdf

1、FORD LABORATORY TEST METHOD BN 108-09 Date 2001 10 31 2000 03 07 1994 O9 28 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CARPETS Action Revisions Revised Editorial - no technical change A. Cockman Revised Editorial - no technical change A. Cockman Application This procedure is used to determine the res

2、istance to bearding and frosting of automotive carpeting. Apparatus Required Flexing Machine Flex and Fold Tester or equivalent device which has a stroke adjustment of 63 - 100 mm, a reciprocating rate of 37 double strokes per minute, equipped with a reciprocating arm drilled and tapped as shown in

3、Illustration 1. Source: Custom Scientific Instruments Division of Atlas Electric Devices 13 Wing Drive Cedar Knolls, N.J. 07927 fax: 973-984-6793 ph: 973-538-8500 Mounting Base Base for holding carpet specimen. (See Illustration 2.) Clamp Bars Two clamps to hold mounting base. (See Illustration 3.)

4、Weight 680 g steel plate 150 x 100 mm. (See Illustration 4.) Carrier 100 x 150 x 12 mm wood platform for attaching card clothing. (See Illustration 4.) Card Clothing 22 mm height - 3 rib set, 6 rows, 11 Noggs #30 wire 5 ply rubber backing. (See Illustration 4.) Source: Howard Brothers Manufacturing

5、Company Auburn, Ma ph: 508-793-7070 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 108-09 Bolts Four 1/4 in diameter bolts, 4 in long. (See Illustration 4.) Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlle

6、d atmosphere of 23 +/- 2 “C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. 2. 3. 4. 5. 6. 7. Cut a carpet sample 100 x 200 mm with the long dimension in the across machine direction of the carpet.

7、 Mount the sample on the mounting base, with the long dimension in the direction of the stroke. Staple the sample on each side in several locations. Assure that sample lies flat and is rigid. Position carrier on reciprocating arm with the 680 g weight, as shown in Illustration 5. Assure that carriag

8、e bolts do not bind in holes in reciprocating arm, preventing carrier from wobbling, or “floating“ during operation. Position mounting base with carpet sample on Flex and Fold Tester with two clamp tars. Center carpet sample under card clothing at middle of stroke. Set the machine for 88 mm stroke.

9、Start tester and test for 1 O0 cycles. At the end of test, evaluate sample for degree of bearding and frosting according to engineering specification requirement. Procedure for Breaking In Card Clothing New card clothing must be broken in to remove burrs and sharp edges on wire ends, by operating 2,

10、000 cycles using a carpet specimen of any BCF nylon loop pile carpeting. A second carpet specimen must then be tested and compared to a specimen tested with previous card clothing to assure that results are similar. Card clothing and carrier must be replaced whenever the bearding results on a contro

11、l carpet become less severe than the original control carpet sample that was run after the breaking-in period. If card clothing bristles become too flexible or base shows evidence of delaminating, card clothing should be replaced. No card clothing brush should be used after 10,000 cycles. Chemicals,

12、 materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Page 2 of 7 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 108-09 BEARDING AND FROSTING TE

13、ST FOR AUTOMOTIVE CARPETS 5116 in. -TAP 118 IN N.D.T. 11/32 IN. TAP DRILL 16 DEEP - 61 1 118 IN. DRILL - v r Y 25.4 4 602 0.75 X 45“- CHAMFER ALL EDGES 15.8 IN. DIA. 1 * F I H I I - fl *ML 25.4 tt 4 13 794 DIMENSIONS IN MM UNLESS OTHERWISE SPECIFIED RECIPROCATING ARM MATERIAL: STEEL Illustration 1 P

14、age 3 of 7 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 108-09 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CARPETS MATERIAL BIRCH MOUNTING BASE - I REQD ALL DIMENSIONS IN MM Illustration 2 Page 4 of 7 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METH

15、OD BN 108-09 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CARPETS MATERIAL: BIRCH L2 HOLES - 8.8 DIA. CLAMPING BAR - 2 REQD. ALL DIMENSIONS IN MM T Illustration 3 Page 5 of 7 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 108-09 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CAR

16、PETS 4 HOLES 5/16 IN. DIA. SAME LOCATION AS CARRIER 1 WEIGHT - 1 REQD MATERIAL: STEEL WEIGHT: 680g CARRIER - 1 REQD MATERIAL: BIRCH OR EQUIVALENT HARDWOOD DIMENSIONS IN MM UNLESS OTHERWISE INDICATED Illustration 4 Page 6 of 7 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD B

17、N 108-09 BEARDING AND FROSTING TEST FOR AUTOMOTIVE CARPETS NOTE: 114 IN. DIA. CARRIAGE BOLTS ASSEMBLED THROUGH 5/16“ 18 TAP HOLES ALLOWS CARRIER TO WOBBLE OR “FLOAT“ DURING TESTING - DIMENSIONS IN MM UNLESS OTHERWISE INDICATED RECIPROCATING ARM CARPET SAMPLE MOUNTING BASE Illustration 5 Page 7 of 7 Copynght02001, Ford Global Technologies, Inc