FORD FLTM BN 153-01-2017 LIQUID REPELLENCY COATING VERFICIATION TEST.pdf

1、 FORD LABORATORY TEST METHOD BN 153-01 Date Action Revisions Rev. 0 2017 02 15 Released K. Waugh, L. Schmalz, FNA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 5 LIQUID REPELLENCY COATING VERFICIATION TEST Application This procedure is used to assess the pre

2、sence of liquid repellent coatings on interior seating fabric materials. Apparatus and Materials Required Deionized Water 5 mL Dosing Syringe, for dispensing deionized water onto specimens Digital Camera, for evaluation and documentation Ruler/Grid Board, for reference in photographs Chemicals, mate

3、rials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Procedure 1. Cut a 100 mm by 100 mm specimen from the fabric sample. The specimen shall not contain any decorative stitching

4、 and should lay flat (Figure 1). Specimens should have foam laminated at 3mm minimum thickness by a production lamination process for proper evaluation (Figure 2). 2. Condition the specimen for no less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidi

5、ty. Testing of the material should occur in the conditioning environment or soon after removal. 3. Place fabric specimen on flat surface with grid board or ruler for reference (Figure 1). Once placed, the fabric and ruler/grid should not be moved. 4. Using a syringe, slowly dispense 5 mL of room tem

6、perature deionized water from a height of approximately 10 mm onto the surface of the fabric, avoiding any splashing to allow the full 5mL of water to be dispensed onto the specimen. The water should create one continuous pool on the fabric surface. 5. Immediately after dispensing the DI water, take

7、 a photograph of the fabric with the water on the specimen. This photo should capture the entire specimen and the grid or ruler to reference the approximate size of the water pool on the fabric surface (Figures 3 & 5). 6. Wait 30 minutes and photograph the specimen again. This photo should capture t

8、he entire specimen and the grid or ruler to reference the approximate size of the water pool on the fabric surface (Figures 4 & 6). Evaluation 1. Compare the before and after photos of the specimen. Evaluate the approximate size of the pool of water using the ruler or grid in the photos as reference

9、. 2. Determine if the water has soaked into the fabric. FORD LABORATORY TEST METHOD BN 153-01 Copyright 2017, Ford Global Technologies, LLC Page 2 of 5 Report 1. Include photos as report documentation. 2. Indicate Pass or Fail using the criteria below: PASS (See Figure 4) Minimal or No Soak In The p

10、ool of water has not changed or is still apparent on the fabric surface. There is no significant change in size or shape to the water pool on the fabric surface. No change indicates the presence of a soil repellent coating. FAIL (See Figure 6) Complete Soak In The pool of water has completely soaked

11、 into the fabric. No water is apparent on the surface of the fabric. This indicates no soil repellent coating is applied. Figure 1: Example of specimen and ruler prior to test FORD LABORATORY TEST METHOD BN 153-01 Copyright 2017, Ford Global Technologies, LLC Page 3 of 5 Figure 2: Laminate backing o

12、n fabric required for test Figure 3: Example of specimen with soil repellent coating immediately after dispensing DI water FORD LABORATORY TEST METHOD BN 153-01 Copyright 2017, Ford Global Technologies, LLC Page 4 of 5 Figure 4: Example of specimen with soil repellant coating 30 minutes after dispen

13、sing DI water Figure 5: Example of specimen without soil repellant coating immediately after dispensing DI water FORD LABORATORY TEST METHOD BN 153-01 Copyright 2017, Ford Global Technologies, LLC Page 5 of 5 Figure 6: Example of specimen without soil repellant coating 30 minutes after dispensing DI water