FORD FLTM BO 015-03-2000 RESISTANCE OF WOODGRAIN FILMS TO HIGH INTENSITY ULTRAVIOLET EXPOSURE《木纹薄膜的高强度紫外线照射耐受性》.pdf

1、 FORD LABORATORY TEST METHOD BO 015-03 Date Action Revisions 2000 11 09 Revised Editorial no technical change A. Cockman 1992 07 20 Printed copies are uncontrolled Page 1 of 4 Copyright 2000, Ford Global Technologies, Inc. RESISTANCE OF WOODGRAIN FILMS TO HIGH INTENSITY ULTRAVIOLET EXPOSURE Applicat

2、ion This procedure is used to test the resistance of wood grain films to artificial weathering by simultaneous exposure to intense ultraviolet energy and water immersion. Apparatus Required A modified oven equipped with four Westinghouse FS20T - 12 fluorescent sunlamps, five General Electric G25T -8

3、 germicidal lamps, and a rotating platform is required. The oven shall be maintained at 32 +/ - 3 C for this test. Oven Grieves He ndry, Model PL - 1, 1000 watts. O.D. - 30 inches wide, 25 inches deep, 24 inches high. I.D. - 28 1/2 inches wide, 24 inches deep, 20 1/2 inches high. 110 V, AC, 50 - 60

4、cycle, single phase motor. The oven is to be equipped with thermostat control and red pi lot light. An oven stand is optional. Lamp Fixture 20 gage still box with screw cover. Two two - lamp, 20 watt high power factor ballasts for sunlamps. Five one - lamp, 25 watt high power factor ballasts for ger

5、micidal lamps. Seven manual fluorescent starter switch assemblies. Cover - 20 gage steel with Alzak aluminum reflector overlay. Four pairs of fluorescent lamp holders. Five pairs of germicidal lamp holders. Five G25T - 8 germicidal lamps (General Electric) or equivalent. Rear of box shall be provide

6、d wi th four 1/4 - 20 mounting studs and screened ventilation sunlamps. Four FS20T - 12 fluorescent sunlamps (Westinghouse) or equivalent. Lamps are to be mounted alternately. The above lamp fixture is to be installed in the oven ceiling. Rotating Platform One 12 inch diameter platform. 110 V, AC, 5

7、0 - 60 cycle, single phase motor - gear assembly capable of rotating platform at 3 - 5 rpm. Adjustable stand to position motor and platform. Pyrex Tray 6 x 10 inches (or equivalent non - metallic tray). FORD LABORATORY TEST METHOD BO 015-03 Page 2 of 4 Copyright 2000, Ford Global Technologies, Inc.

8、Test Panels Ty pe 301 stainless steel, sheared from bright annealed strip, approximately .076 cm thickness. Panels to be approximately 5 x 5 cm. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosp here of 23 +/ - 2 C and 50 +/ -

9、5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure Caution: Severe eye damage can result from direct or indirect viewing of the germici dal lamps with the unprotected eye. 1. Apply woodgrain film to a 2 x 2 inch st

10、ainless steel panel. 2. Lay panels in the Pyrex tray assuring no panels overlapping. 3. Add distilled water to a depth of approximately 1/8 inch above test samples. 4. Mainta in water level throughout UV exposure period. 5. Adjust distance of rotating platform to 3 1/4 inches below lamps. 6. Expose

11、samples to the number of cycles specified in the material specification. Each cycle consists of the following: 8 h UV (germicid al and sunlamp) exposure at 32 +/ - 3 C. Remove from cabinet, hold at 23 +/ - 2 C and ambient humidity for 16 h. 7. The platform is to be rotated continuously during the 8

12、h exposure period at 3 to 5 rpm. 8. At the conclusion of the specified number of cycles, including the 16 h recovery, place the samples in a 70 +/ - 3 C oven for 15 minutes. Reporting Examine and report any changes in appearance or other physical properties occurring as a result of this test as requ

13、ired by the material specification . Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BO 015-03 Page 3 of 4 Copyright 2000, Ford Global Technologies, Inc. RESISTANCE OF WOODGRAIN FILMS TO HIGH INTENSITY ULTRAVIOLET EXPOSURE FORD LABORATORY TEST METHOD BO 015-03 Page 4 of 4 Copyright 2000, Ford Global Technologies, Inc. RESISTANCE OF WOODGRAIN FILMS TO HIGH INTENSITY ULTRAVIOLET EXPOSURE