FORD FLTM BP 122-01-2007 DETERMINATION OF COLD ADHESION REQUIREMENTS OF WEATHERSTRIP LOW FRICTION COATINGS TO PAINTED METAL OR GLASS《挡风雨条的低摩擦涂层对涂漆金属或玻璃的低温粘附力要求的测定》.pdf

1、 FORD LABORATORY TEST METHODBP 122-01Date Action Revisions 2007 02 21 Revised Updated to reflect general apparatus conditions K. Mueller 2001 09 25 Revised Editorial no technical change A. Cockman 1996 11 15 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 1 of 4 DE

2、TERMINATION OF COLD ADHESION REQUIREMENTS OF WEATHERSTRIP LOW FRICTION COATINGS TO PAINTED METAL OR GLASS Application This method was developed to determine the ice release properties of coatings applied to body seals, such as weatherstrips. Materials and Apparatus Required Weatherstrip Ice Release

3、Apparatus (Figure 1) Model NTS 96148 or equivalent with operating speed of 250 +/- 10 mm/minute. Apparatus or prints can be supplied by: Source: National Technical Systems 12601 Southfield Road Detroit, MI 48223 Telephone: (313) 835-0044 FAX: (313) 272-1190 Weatherstrip Mounting Block Block designed

4、 to hold weatherstrip at proper angle and to fit apparatus. Force Gage Chatillon Force Gage Model #DFG-50 or equivalent to fit apparatus. Environmental Chamber CSZ Chamber Model #ZH3222H/AC or equivalent front opening chamber capable of -40 C with wall port approximately 50 mm in diameter. Contact P

5、anel Steel Panel painted per FLTM BI 103-02, or as specified, for body closure seals or glass plate for sliding glass seals. Cleaning Items Isopropyl alcohol. Paper toweling, low lint, nonabrasive. FORD LABORATORY TEST METHODBP 122-01Printed copies are uncontrolled Copyright 2007, Ford Global Techno

6、logies, LLC Page 2 of 4 Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified

7、 Adequate humidity is required to provide sufficient moisture condensation on the test surfaces, which forms the ice coating interface upon freezing. A front opening environmental chamber, rather than a top opening chamber, is utilized to allow the humid air exchange necessary to establish this con

8、densation. Procedure 1. Cut five 150 mm sections off the weatherstrip to be tested. Five specimens are to be tested for each weatherstrip coating to obtain a final average value. 2. Mount a cut section of the weatherstrip onto the mounting block, and mount the appropriate contact panel onto the oppo

9、sing backing plate of the test fixture. 3. After mounting, clean the weatherstrip and contact panel with isopropyl alcohol and paper toweling to remove any contamination from handling. 4. Mount the Ice Release Apparatus through the environmental chamber wall in such a position that the force gauge i

10、s vertical/horizontal outside the chamber, and the weatherstrip mounting block holder is vertical/horizontal inside the chamber. Place the test fixture (mounting block and backing plate) into the apparatus. The panel backing plate must be securely locked to the actuator rod so that it separates stra

11、ight away from the weatherstrip during the test. It shall not be allowed to pivot or tilt, which would result in a peeling type of separation. 5. Adjust the actuator stop bracket on the apparatus so that the test sample compressed position duplicates the in-body closed position. There should be no s

12、pacers or adjusting screws between the mounting block and the contact panel or panel backing plate. They may freeze to the surfaces and cause erroneous force readings. 6. With non load on the weatherstrip, zero the force gauge in the tension ode. 7. Fully compress the weatherstrip by running the act

13、uator until it contacts the stop bracket and stops or slips. 8. Close the environmental chamber door and allow the fixture to cool to -40 C for 1 hour. 9. After 1 hour turn off the chamber and start the actuator motor so that the painted panel separates from the weatherstrip. Note any load from the

14、force gauge. 10. Open the environmental chamber door and allow the painted panel and weatherstrip to accumulate the maximum amount of moisture condensation on the surfaces, which should occur in approximately 15 minutes. The condensing moisture first appears as a uniform coating of frost. When the f

15、rost changes to a wet phase, it has achieved the optimum condition. Proceed immediately from this condition. No additional moisture should be required. 11. With no load on the weatherstrip, rezero the force gauge in the tension mode. 12. Fully compress the weatherstrip by running the actuator to the

16、 stop bracket again. FORD LABORATORY TEST METHODBP 122-01Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 3 of 4 13. Close the environmental chamber door and allow the fixture to cool to -40 C for 1 hour. 14. After 1 hour turn off the chamber and start the actuator

17、motor so that the painted panel separates from the weatherstrip. Record the peak load from the force gauge. 15. Repeat the test five times using a different specimen of weatherstrip each time. Dry and clean the painted or glass panel prior to each test. Note: A soft wiper seal may be required around

18、 the force gauge extension rod to prevent frost buildup and possible erroneous force readings. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHODBP 122-01Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 4 of 4 TEST APPARATUS Figure 1