ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:47.90KB ,
资源ID:747510      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747510.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM BU 003-2-2000 BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES.pdf)为本站会员(fuellot230)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM BU 003-2-2000 BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES.pdf

1、 FORD LABORATORY TEST METHOD BU 003-02 Date Action Revisions 2000 11 10 Revised Editorial no tech nical change A. Cockman 1992 03 02 Printed copies are uncontrolled Page 1 of 4 Copyright 2000, Ford Global Technologies, Inc. BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES Application This procedure

2、is used to test the block shear strength of thermosetting adhesives used for bonding metal to metal. Apparatus Required Press An air driven press which will deliver a constan t pressure to the test specimens during cure is required. The press is equipped with controlled electric heaters which heat t

3、he test specimens to required temperature during cure under pressure. (See sketch.) Oven A mechanical convection oven maintained at 175 +/ - 5 F is required for drying the adhesive coating. Tensile Tester A tensile testing machine with a scale range of 0 - 10,000 lbs and capable of applying a load a

4、t a uniform rate of 0.050 inch/minute is required. The tensile machine shall have an indicator for recording the shear strength in pounds of the adhesive at the moment of rupture. Shear Strength Fixture The fixture for holding the bonded test specimen during loading is shown in the attached sketch.

5、The fixture is equipped with an elec trically controlled heater for determining shear strength at elevated temperatures. Abrasive Paper or Sand Blast Alundum, 4/0 150 grit with cloth backing, is used for polishing the mating surfaces of the test specimens or sand blast (depending on surface desired)

6、. Sand or Grit Size on #20 Sieve - 12 % max on #50 Sieve - 1 % max Pressure used - 100 psi FORD LABORATORY TEST METHOD BU 003-02 Page 2 of 4 Copyright 2000, Ford Global Technologies, Inc. Exposure time - 30 seconds per square inch Nozzle distance to specimen - 3 inches Nozzle size - 3/8 inch Test Sp

7、ecimens Each test specimen assembly consists of one strip and one disc of 24ST aluminum. The strip is 1 1/8 by 4 3/8 x 1/4 inch and the disc is 1 1/8 inch diameter by 1/4 inch thick. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled a

8、tmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Polish the mating surfaces of an aluminum strip and disc to a sm ooth uniform surface with 4/0 150 grit alundum polishing c

9、loth. 2. Wipe clean with a cloth wetted with ESF - M5B99 - A Trichloroethylene. 3. Lay a number of the aluminum strips on a flat surface with their long edges touching and parallel. Lay three layers of 0.007 inch thick tape across each end of the test specimens as shown. This buildup of tape will as

10、sist in leveling a 0.021 inch thick layer of wet adhesive across the center of each test specimen. Spread and level the adhesive with a spatula. FORD LABORATORY TEST METHOD BU 003-02 Page 3 of 4 Copyright 2000, Ford Global Technologies, Inc. Note: This procedure should give approximately a 0.007 inc

11、h thick dry film thickness with a 40 % total solids adhesive. To obtain the 0.006 - 0.008 inch total dry film thickness desired with less total solids, more thickness of tape will be necessary. Four layers of 0.007 inch tape would be required with 26 % solids adhesive. 4. Remove the tape and air dry

12、 the specimens for 15 minutes followed by a bake in the oven for 20 minutes at 175 +/ - 5 F. 5. Cool to 23 +/ - 2 C and bond an aluminum disc to t he coated area of each aluminum strip with finger pressure. 6. Position the test specimen in the press, locating the hole in the disc over the pin in the

13、 press and apply the required load for the time and temperature as indicated by the material specifica tion or laboratory request. 7. Allow the bonded specimens to cool, position in the test fixture used for shear adhesion (see sketch) and apply a load at 0.050 inch per minute to failure of the bond

14、. The temperature at which the shear strength test is det ermined shall be as specified on the laboratory request. 8. Report the shear strength of the specimen in pounds, temperature of the test, type of adhesive, cure time and temperature. Chemicals, materials, parts, and equipment referenced in th

15、is document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BU 003-02 Page 4 of 4 Copyright 2000, Ford Global Technologies, Inc. BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES Block Shear Strength Test Fixture (Exploded View)

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1